image of a properly lit sailboat at night

What is a Properly Lit Sailboat at Night? (A Guide to Safety Regulations)

Have you ever been out on the open water and seen a sailboat with its lights on at night? It’s a beautiful sight to behold.

But did you know that there are specific safety regulations in place for properly lit sailboats? In this guide, we’ll be looking at the importance of having a properly lit sailboat, what types of lights are needed, how to install them, and how to test for proper operation.

Let’s get started and learn how to stay safe on the waters!

Table of Contents

Short Answer

A properly lit sailboat at night is a boat that is equipped with the correct navigation lights, which are required by law.

These lights must be visible for two miles and should include a green light on the starboard side, a red light on the port side, and a white light aft.

Additionally, the boat must also have a white masthead light that is visible for three miles.

The masthead light should be mounted at least two meters above the hull.

What Are the Safety Regulations for Properly Lit Sailboats?

When it comes to sailing at night, safety is of the utmost importance.

Properly lit sailboats ensure that they are visible to other boats, which reduces the risk of collisions and other accidents.

In order to ensure that a sailboat is properly lit at night , there are certain safety regulations that must be followed.

First and foremost, the sailboat must have the correct lighting equipment installed and in good working order.

This includes running lights (red and green lights found at the bow and stern of the vessel), an anchor light (a white light mounted on the masthead or the bow of the vessel), a stern light (a white light placed at the stern of the vessel), and a masthead light (a white light placed at the highest point on the vessel).

The running lights, anchor light, and stern light must be visible for at least 3 miles in clear conditions.

This allows other boats on the water to easily spot the sailboat, even in the dark.

The masthead light must be visible for at least 2 miles in clear conditions.

This ensures that the sailboat is easily seen from all directions.

In addition to having the correct lighting equipment, sailboats must also be equipped with a white all-round light.

This light must be visible for at least 2 miles in clear conditions and must be mounted on the mast at least 9 meters (or 30 feet) above the waterline.

The all-round light is an important part of a sailboats lighting system as it allows other boats to easily spot the sailboat from any direction.

These are just a few of the safety regulations that must be followed when it comes to properly lit sailboats.

Following these regulations will help to ensure that a sailboat is visible to other vessels on the water and will help to reduce the risk of accidents and collisions.

It is important that all sailors understand and adhere to these regulations in order to remain safe on the water.

Types of Lights Needed for Proper Lighting

When it comes to lighting a sailboat at night, there are a few key components that must be in place in order to ensure the safety of the vessel and the crew.

The most important of these components is the correct type of lighting equipment.

This includes various running lights, anchor lights, masthead lights, and stern lights.

Running lights are the red and green lights that are mounted on the bow and stern of the vessel, and are used to show the direction of travel of the boat.

They must be visible for 3 miles in clear conditions, making it easier to spot the boat in the dark.

Anchor lights are white lights that are mounted on the masthead or the bow of the vessel, and are used to show that the boat is anchored.

They must also be visible for 3 miles in clear conditions.

The stern light is a white light placed at the stern of the vessel.

This is used to show the direction of travel of the boat and should also be visible for 3 miles in clear conditions.

Finally, the masthead light is a white light placed at the highest point on the vessel.

This light is used to help identify the boat to other vessels on the water, and must also be visible for 3 miles in clear conditions.

Having all of these lights in good working order is essential for the safety of the boat and the crew.

It is important to make sure that all lights are visible from a distance of 3 miles in clear conditions, as this will make it easier to identify the boat in the dark.

It is also important to make sure that all lights are regularly inspected and maintained in order to ensure that they are in good working order.

How to Install the Lights

Installing the lights for a properly lit sailboat at night is an essential part of staying safe while sailing.

It is important to ensure that all of the lights are in good working order and that they meet the safety regulations for visibility.

The first step is to select the right lights for your vessel.

There are two main types of lights running lights and anchor lights.

Running lights are the green and red lights found at the bow and stern of the vessel, while anchor lights are white lights mounted on the masthead or bow of the vessel.

Once the lights are selected, the next step is to install them.

Start by attaching the anchor light to the masthead or bow of the vessel.

The anchor light should be securely mounted and wired in accordance with the manufacturers instructions.

Next, attach the stern light at the stern of the vessel.

This should also be securely mounted and wired in accordance with the manufacturers instructions.

Finally, attach the running lights.

These should be mounted at the bow and stern of the vessel.

It is important to test the lights after installation to make sure they are working properly.

Make sure that the lights meet the visibility requirements of 3 miles in clear conditions, as this is the minimum distance that the lights must be visible from.

Once the lights are installed and tested, youre ready to set sail in the dark!

Importance of Properly Lit Sailboats

When it comes to sailing, safety is of the utmost importance.

This is why it is essential for all sailboats to be properly lit at night.

Having the correct lighting equipment installed and in good working order is a critical component to ensure visibility and the safety of everyone on the water.

Not only does having properly lit sailboats maintain the safety of the sailors on the boat, but it also helps to prevent collisions with other vessels.

It is much easier to spot a sailboat on the water at night when it has the correct lighting equipment, such as running lights, anchor lights, stern lights and masthead lights.

All of these lights should be visible for at least 3 miles in clear conditions, making it much easier to spot a sailboat on the water.

Additionally, having properly lit sailboats at night is also important for law enforcement and marine patrol officers.

It makes it easier for them to identify and inspect boats, ensuring that all safety regulations are being followed.

This helps to keep the waterways safe for all boaters.

For these reasons, it is important for all sailboats to be properly lit at night.

By having the right lighting equipment installed and in good working order, it can help to maintain the safety of everyone on the water, as well as help to prevent collisions with other vessels.

It also makes it easier for law enforcement and marine patrol officers to identify and inspect boats, helping to keep the waterways safe for all boaters.

Different Types of Lights and Their Functions

When it comes to lighting a sailboat at night, there are several different types of lights that must be installed and in good working order in order to ensure the safety of the vessel and its occupants.

The most common types of lights used on sailboats are running lights, anchor lights, stern lights, and masthead lights.

Running lights are the green and red lights found at the bow and stern of the vessel.

These lights are typically used to signal the direction of the boats movement, and must be visible for 3 miles in clear conditions.

The green light is typically placed on the port side (left side) of the boat, and the red light is placed on the starboard side (right side).

Anchor lights are white lights mounted on the masthead or bow of the vessel.

They are used to indicate that the boat is at anchor, and must also be visible for 3 miles in clear conditions.

Stern lights are white lights placed at the stern of the vessel.

These lights indicate the boats direction of travel, and must be visible for 2 miles in clear conditions.

The masthead light is a white light placed at the highest point on the vessel.

This light is typically used in conjunction with the stern light to indicate the direction of travel, and must be visible for 2 miles in clear conditions.

In addition to these lights, boats may also be fitted with a variety of other lights such as tricolor lights, sidelights, all-round lights, and deck lights.

These lights are typically used to indicate the presence of the vessel in low-visibility conditions, and must be visible for 2 miles in clear conditions.

It is important to ensure that all lights on a sailboat are in good working order and visible from a distance in order to make the vessel visible to other boats and comply with safety regulations.

A properly lit sailboat at night is one that has the correct lighting equipment installed and in good working order.

Benefits of Properly Lit Sailboats

Having a properly lit sailboat at night is essential for staying safe on the water.

With the right lighting equipment installed and in good working order, you can be easily seen by other vessels and prevent possible collisions.

Additionally, having the right lights on your sailboat can help other boaters determine your vessels size, direction, speed, and even your intentions on the water.

Having the right lights can also give you a sense of security while youre out at night.

Knowing that youre visible to other vessels reassures you that youll be able to be seen and spotted if you need assistance or if theres an emergency.

When youre out on the water at night, having a properly lit sailboat can also make navigation easier.

By having the correct lighting equipment installed, youll be able to easily spot buoys, markers, and other vessels, making it easier for you to stay on course and reach your destination in a timely manner.

Having the proper lights also helps to keep your sailboat in compliance with safety regulations.

If youre stopped by the coast guard or other law enforcement, having the right lights can help to avoid any potential fines or penalties.

Overall, having a properly lit sailboat at night is essential for staying safe on the water.

Not only does it make it easier for other vessels to spot you, but it can also help with navigation and make sure that youre in compliance with safety regulations.

Properly lit sailboats can also give you a sense of security and peace of mind, knowing that youre visible to other vessels in the area.

How to Test Lights for Proper Operation

Testing lights on a sailboat at night is an important part of ensuring that the craft is properly lit and visible to other vessels.

It is essential for safety, as well as compliance with regulations set by the United States Coast Guard.

Before each voyage, it is important to inspect all of the lights and make sure that they are in proper working order.

The first step to testing lights is to turn them on and check that they are functioning correctly.

It is important to make sure that all of the required lights are present and that they are bright enough to be seen in clear conditions for up to 3 miles away.

The running lights should be a green light at the bow and a red light at the stern, while the anchor light should be a white light mounted on the masthead or the bow of the vessel.

The stern light should be a white light placed at the stern, and the masthead light should be a white light placed at the highest point on the vessel.

Another important step in testing lights is to make sure that they are not obstructed in any way.

This includes checking for any wires, cables, or other objects that could block the lights from being visible.

This is especially important for the masthead light, as it needs to be accessible in order to be seen from a distance.

It is also important to check the wiring of the lights to make sure that they are securely connected and not corroded or damaged.

Finally, it is important to check the bulbs of the lights to make sure that they are all functioning correctly.

It is important to check the wattage of the bulbs to make sure that they are bright enough to meet the standards set by the United States Coast Guard.

It is also important to make sure that the bulbs are not cracked or damaged in any way, as this could affect their visibility.

Following the steps outlined above will help to ensure that all of the lights are in proper working order and can be seen from a distance in clear conditions.

This is important for safety, as well as compliance with regulations set by the United States Coast Guard.

Final Thoughts

Having the correct lights installed and in proper working order on your sailboat is essential for safety and visibility on the water at night.

Knowing what type of lights you need, how to install them, and how to test them for proper operation is key.

While it may seem daunting to install and maintain all these lights, the benefits of having a properly lit sailboat at night far outweigh the effort.

So take the time to review safety regulations, and make sure you have the right lights installed and operating correctly to ensure a safe and enjoyable sailing experience.

James Frami

At the age of 15, he and four other friends from his neighborhood constructed their first boat. He has been sailing for almost 30 years and has a wealth of knowledge that he wants to share with others.

Recent Posts

When Was Banana Boat Song Released? (HISTORICAL INSIGHTS)

The "Banana Boat Song" was released in 1956 by Harry Belafonte. This calypso-style song, also known as "Day-O," became a huge hit and remains popular to this day for its catchy tune and upbeat...

How to Make Banana Boat Smoothie King? (DELICIOUS RECIPE REVEALED)

To make a Banana Boat Smoothie King smoothie at home, start by gathering the ingredients: a ripe banana, peanut butter, chocolate protein powder, almond milk, and ice. Blend the banana, a scoop of...

The Night Vision Techniques

Explore the techniques and tools for safely sailing under the stars with our comprehensive guide to night sailing, from preserving your night vision to navigating in the dark and following proper etiquette.

The Night Vision Techniques: A Comprehensive Guide to Night Sailing

Sailing under the stars can be a magical experience, but it also presents unique challenges and requires a different set of skills than daytime sailing. In this article, we’ll explore the essential techniques for maintaining your night vision, as well as tips for navigating and staying safe during your nocturnal adventures on the open sea.

Table of Contents

Understanding night vision, preserving your night vision, navigating at night, safety tips for night sailing, night sailing etiquette.

Before we dive into the techniques for maintaining your night vision, it’s important to understand how our eyes work in low-light conditions. Our eyes have two types of photoreceptor cells: rods and cones. Cones are responsible for color vision and function best in bright light, while rods are more sensitive to light and are responsible for our ability to see in low-light conditions.

In darkness, our eyes undergo a process called dark adaptation, which allows the rods to become more sensitive to light. This process can take anywhere from 20 to 45 minutes, depending on the individual and the level of darkness. Once our eyes have fully adapted, we can see much better in the dark, but it’s important to note that our night vision is still limited compared to our daytime vision.

Now that we understand the basics of night vision, let’s explore some techniques for preserving it while sailing at night:

1. Limit Exposure to Bright Light

The most important factor in maintaining your night vision is to limit your exposure to bright light. This includes both natural sources, such as the moon and stars, and artificial sources, such as cabin lights and electronic devices. To minimize exposure to bright light:

• Keep cabin lights dimmed or turned off when not in use.
• Use red or amber lights instead of white lights, as these colors are less disruptive to night vision.
• Avoid looking directly at bright light sources, such as the moon or other boats’ lights.
• Limit the use of electronic devices with bright screens, or adjust the brightness settings to minimize glare.

2. Allow Time for Dark Adaptation

As mentioned earlier, it takes time for our eyes to fully adapt to darkness. Before setting sail at night, spend some time in a dimly lit environment to allow your eyes to adjust. If you need to transition from a brightly lit area to a dark one, close your eyes for a few minutes to help speed up the adaptation process.

3. Use Peripheral Vision

Our peripheral vision is more sensitive to light than our central vision, making it more effective for detecting objects in low-light conditions. When scanning the horizon or searching for objects in the water, try looking slightly to the side of the object rather than directly at it. This will allow you to use your peripheral vision and increase your chances of spotting the object.

4. Keep One Eye Covered

If you need to briefly expose yourself to bright light, such as when checking a chart or using a flashlight, try covering one eye to preserve its night vision. This technique, known as the “pirate’s patch,” can help minimize the impact of bright light on your overall night vision.

Navigating at night presents its own set of challenges, but with the right techniques and tools, you can safely and confidently sail under the stars. Here are some tips for night navigation:

1. Familiarize Yourself with the Night Sky

Learning to recognize constellations and other celestial landmarks can be a valuable skill for night navigation. Familiarize yourself with the night sky and practice identifying key constellations, such as the North Star (Polaris), which can help you determine your latitude and direction.

2. Use Electronic Navigation Tools

While celestial navigation is a valuable skill, modern electronic navigation tools, such as GPS and chartplotters, can provide more accurate and reliable information. Make sure your navigation equipment is in good working order and that you’re familiar with its operation before setting sail at night.

3. Keep a Close Eye on the Weather

Weather conditions can change rapidly at sea, and poor visibility due to fog, rain, or clouds can make night navigation even more challenging. Keep a close eye on the weather forecast and be prepared to adjust your plans if necessary.

4. Maintain a Proper Lookout

Maintaining a proper lookout is essential for safe night sailing. In addition to scanning the horizon for other vessels and obstacles, pay close attention to the water’s surface for signs of changes in depth or the presence of debris. Remember to use your peripheral vision and avoid staring directly at bright light sources.

In addition to the navigation tips above, there are several safety precautions you should take when sailing at night:

1. Ensure Your Boat is Properly Lit

Make sure your boat’s navigation lights are functioning properly and are visible from all angles. This will help other vessels see you and avoid collisions.

2. Wear Reflective Clothing and Gear

Wearing reflective clothing and gear, such as life jackets and harnesses, can help make you more visible to other boaters and increase your safety on the water.

3. Keep a Sharp Ear

In addition to maintaining a proper lookout, use your sense of hearing to detect potential hazards. Listen for the sound of waves breaking on nearby shores, the hum of approaching engines, or the calls of other sailors.

4. Be Prepared for Emergencies

Before setting sail at night, make sure you have a well-stocked emergency kit on board, including flares, a VHF radio, and a flashlight with spare batteries. Familiarize yourself with emergency procedures and be prepared to act quickly in case of an emergency.

Finally, it’s important to be considerate of other sailors and follow proper etiquette when sailing at night:

• Keep noise levels to a minimum, as sound travels farther over water at night.
• Be mindful of your boat’s lights and avoid shining them directly at other vessels.
• Give other boats plenty of space and avoid crowding popular anchorages or mooring areas.

Night sailing can be a thrilling and rewarding experience, but it requires a different set of skills and precautions than daytime sailing. By understanding the principles of night vision, practicing proper navigation techniques, and following safety guidelines, you can confidently set sail under the stars and enjoy the unique beauty and freedom of the open sea at night.

Boat Navigation Lights Rules: Illustrated Beginners Guide

When navigating at night, the lights on other boats are your first clue about the moving dangers around you. And your navigation lights are your first line of safety in avoiding collisions in the dark, and they tell others vessels what you are and what you are doing. The rules sound complex, but with a little understanding you can get the basics for any situation.

So what are the basic navigation light rules? For most small vessels, motoring requires red and green (port and starboard) lights, and a white light visible in all directions around the boat. This is almost always a stern light and a masthead light on sailboats. Boats under sail require port and starboard lights, and a white stern light. Sailboats below sixty-five feet may show a tricolor light at the masthead instead of side and stern lights when sailing.

That's it, in a nutshell. There's a little more to it, as the rules change with different sizes and there are some specifics about angles of display for the colors. Identifying other ships at sea requires more study, but the basics are the same. And it's not much trouble to make sure you've always got the proper lights on your vessel.

On this page:

What are the official colregs rules for your sailboat, what about the uscg (united states coast guard) rules, lighting at anchor, identifying the boats around you.

The International Regulations for the Prevention of Collision at Sea , abbreviated "COLREGS" is very specific about the lights required, their shapes and sizes, and the distance they must be visible. For the smaller boat, the following definitions apply.

• Masthead Light - a white light placed centerline on the boat showing an arc of 225 degrees with 112.5 degrees either side of the front of the vessel.
• Sidelights - A red light on the port side and a green light on the starboard. They must show an arc of 112.5 degrees from centerline of the bow.
• Stern light - A white light on the stern of the boat showing an unbroken arc of 135 degrees from centerline of the vessel.
• All-round light - A light showing in an unbroken arc of 360 degrees.

The good news is you need not measure these angles. Any properly installed USCG or COLREGS approved light which will cover the correct arcs. If you have to replace the original light from your boat, make sure it's with an approved replacement.

Lights When Sailing

The specific rules for a sailboat under sail are in COLREGS Rule 25 and vary slightly with the size of the boat. A sailboat powering is considered a power boat and falls under in Rule 23.

• Under 23 feet (7 meters) - side lights and a stern light, possible. If these lights can not be displayed a light must be kept at hand to help avoid a collision. This can be a bright flashlight.
• Over 23 feet - Side lights visible to one nautical mile and stern light visible for two.
• Vessels under 65 feet may combine both sidelights into a single lantern on the bow.
• May show a tricolor light on the masthead instead of sidelights and a stern light. It's one or the other though, do not show these lights at the same time .
• Masthead light must be visible for three nautical miles, all other lights must have a two nautical mile visibility.
• Side lights must be separated.
• May not show a masthead tricolor light.
• Masthead light must have five nautical mile visibility, all other lights must be visible for two nautical miles.
• Optional masthead lights - any vessel under sail may display a red light over a green light at the masthead with sidelights and stern light. The red over green may NOT be displayed with a masthead tricolor light. It's one set or the other.

Lights When Motoring

For all navigational purposes a sailboat under power is considered a power boat. This includes motor sailing - if the engine is on and providing propulsion you are on a power boat, even if the sails are up . This applies to navigation lighting, sound signals in fog and limited visibility, and rights of way.

Sailboats under 50 meters under power need to show:

• A masthead light
• Stern light

A power-driven vessel under 23 feet (7 meters) that does not exceed seven knots of speed may display an all around white light, though sidelights should be used if available.

The USCG has published its own "Rules of the Road" that are based on the COLREGS. In addition, it has rules for the "Inland Waterways" for rivers, inland lakes and the Great Lakes.

The good news is this has no impact on what you have to do with your own boat.

They mostly relate to lighting changes on towed vessels like barges and tugs. For example, a vessel towing or pushing another vessel in the ocean under COLREGS shows two masthead lights, sidelights and a stern light, whereas in Inland Waterways the towing or pushing vessel displays two yellow towing lights instead of a white stern light.

If you sail on lakes, rivers or the Great Lakes where towed commercial traffic is common you should learn the inland lights, but coastal or ocean sailors will never see these.

When you anchor outside a designated mooring field, you should display an all around white light at the masthead or as high in the boat as practical.

If your boat is large and has a very tall mast, you may wish to display another light closer to the waterline. Boats approaching in the dark may not see a light on a mast sixty or seventy feet in the air when they are close to your boat.

We use a simple garden path light on our stern when we anchor, left in a rod holder or flag socket. It comes on automatically at dusk and is a cheap and easy way to be more visible. There is no specific rule stating you can not display more lights than required, or the nature of any lights beyond the required all around light.

The COLREGS also specify that a round black "daymark" should be displayed in the rigging of any vessel at anchor. Very few small vessels observe this, however it is the correct display for a vessel in an anchorage.

If you tie to a mooring in a marked mooring area you are not required to display anchor lights, but there is no harm in doing so.

The other important reason to know your lights is to figure out what's going on around you at night. The water may be ablaze with white, red, green and other lights at night and they are your first key to avoiding collisions and problems.

All combinations of lights for fishing boats, commercial vessels, and so on are outside this post‘s scope. The odds are small you will encounter a submarine, seaplane or hovercraft at night, but there are regulations regarding specific lighting for each of those vessels!

There are a few fundamentals to help you figure out what that is you see on the horizon, which way it is going, and whether it is a danger to you.

Port Wine is Red

The fundamental rule is that red sidelights will ALWAYS be on the port side of a vessel, and green lights will always be on starboard. However, some vessels can use all around red and green lights for other purposes, though those will be higher than sidelights.

The light‘s on a ship is not important, some large tankers and freighters will have their sidelights far aft and put them on the superstructure for better visibility. It is not safe to assume that sidelights you can see are on the bow of large vessels .

When you can see the color, you know which way the bow is pointing. If it's red, it's pointing more or less to the left and will travel in that direction. A green light shows it is heading more or less to your right.

If you can see the red and green lights at the same time, you are looking directly at the bow of the vessel. When you are far away, this isn‘t as alarming as if you are close crossing. Seeing red and green lights together on a vessel is something you never want to see for long.

Be aware of red and green lights used in combination with other red, green and white lights. These may not be running lights and could have other significance.

Tankers, Freighters and Large Ships

Tankers, freighters and large ships will have side lights, a stern light and a masthead light. In addition, on vessels over 50 meters there will be a second masthead light further aft and higher than the forward light. The masthead light positions are a better tipoff to the bow direction and how far from the bow the sidelights might be. Remember - on a large vessel the sidelights may not be at the bow or even close to it.

USCG Inland Rules allow for a second all-around white light on large vessels on the Great Lakes instead of a second masthead light.

Fishing Boats

Fishing boats engaged in fishing will have more complex light displays. When they aren't fishing, they will show lights like any power vessel, but Rule 26 spells out light combinations that vary by the fishing activity being done. In general:

• Boats which are Trawling but not making headway will display a green all-around light over a white all-around light , and a masthead light aft of these lights. Boats making headway while trawling will show these lights, plus sidelights and a stern light.
• A vessel fishing other than trawling will show a red all-around light over a white all-around light . When making way they will also show sidelights and a stern light.
• If a vessel has gear more than 150 meters away from the boat, it will show a second all around light in the direction of the gear. The best rule is to give fishing boats as wide a berth as you can at night. They're easy to pick out if you check the top light configurations but their course may be difficult to predict.

Towing and Pushing

Towed vessels can be the most dangerous to cross, but they have the most lights to tell you what is happening. Refer to COLREGS or the USCG Rules of the Road Rule 24 for all combinations You can pick a tow/push vessel out with the following lights:

• Two or three masthead lights in a vertical line. Three masthead lights shows a tow over 200 meters. Additional masthead lights may show for larger tow vessels.
• A towing light (yellow light with the same characteristics as a stern light) directly above the stern light.
• The will also have side lights and a stern light.
• The towed vessel will show sidelights and a stern light. Lighting may vary under USCG inland rules, where towing lights may replace stern lights. Learn these differences if this is your regular cruising ground. If you think there is a tow ahead of you, always go well behind the aft most set of lights. Never go between a tow and avoid crossing ahead if possible as it may restrict their maneuverability.

Special Situations

There are several rare situations you may encounter. As a general rule, if there are a lot of lights and you don't understand them look for the sidelights on a moving vessel. If you can find them and figure out the direction it is moving, it makes the vessel easier to avoid. Stay well clear of lights you do not understand if you can avoid them without risk.

Most of these signals are used by larger, commercial vessels and you will not need them.

They use these light combinations with other light combinations. For example a towing vessel may also be restricted in maneuverability, and a vessel constrained by draft will show running lights if moving.

• Not Under Command - two all around red lights in a single line
• Restricted in Ability to Maneuver - red, white then red in a single line
• Constrained by draft - three all around red lights

Leave a comment

You may also like, 17 sailboat types explained: how to recognize them.

Ever wondered what type of sailboat you're looking at? Identifying sailboats isn't hard, you just have to know what to look for. In this article, I'll help you.

The Ultimate Guide to Sail Types and Rigs (with Pictures)

• Multihull Sailor
• Real Estate
• Maintenance & Hardware
• Water Sports

Boat Lights at Night: A Guide to Safe Sailing in the Dark

• 1 Safety Considerations
• 2 Necessary Lights for Boating at Night
• 3 Understanding the Importance of Visibility
• 4 Maintenance and Troubleshooting
• 5 Conclusion

The summer months of the year bring hours of sunshine, giving boaters plenty of time to explore during the day. When the sun sets, safety becomes a priority for anyone operating a boat in the dark. It’s crucial to know which boat lights must be on and how to stay visible and safe while sailing at night.

We’ll provide all the essential information you need to make sailing at night a safer and more enjoyable experience. You’ll get an overview of the different types of boat lights available and tips for staying safe and visible while sailing in the dark.

Safety Considerations

Safety should always be the top priority of any sailor, regardless of the time of day. When boating at night, you must know the rules and regulations in your designated area and familiarize yourself with the navigation equipment on most vessels. Understanding these regulations and investing in additional equipment can make a big difference in ensuring a safe voyage.

It is essential to understand the local laws and regulations regarding boating at night and what lighting you need for each vessel. Boat operators should also be aware of their speed limits, acceptable waterway passage areas, and any potentially hazardous areas they should avoid.

In addition to staying knowledgeable about local regulations, your navigation equipment should be up-to-date and functioning appropriately. Marine vessels typically come equipped with depth sounders and radar systems, but investing in additional accessories can further increase visibility during nighttime sailing. This equipment can include GPS chart plotters or portable AIS receivers, which can help navigate safer routes and alert boat operators of nearby vessels.

Necessary Lights for Boating at Night

Depending on illuminated waters after dark, boat light illumination is necessary for all recreational vessels. Boats must display three main types of lights, including bow, stern, and riding lights.

The bow light indicates to other boats where your vessel’s direction is facing, appearing as a green light on the starboard side and red on the port side when looking forward from the rear. It is important to note that this light should only be visible from directly ahead or nearly directly ahead of the vessel itself. It must have a wide enough angle range for optimal visibility while ensuring it is not too bright or blinding for other boats passing by.

The stern light works similarly to a bow light, except it shines from the back end of a vessel, making it easier for oncoming boats to identify your direction. Per maritime law, this light should also appear white but visible from behind only, ensuring no unnecessary glare toward other boats or obstructions ahead.

Riding lights, or masthead lights, provide additional visibility for your vessel. These lights indicate the vessel’s length according to measurements determined by maritime law enforcement officers. This type of light usually appears as white but occasionally has a blue tint depending on individual regulation standards in your area.

Understanding the Importance of Visibility

When selecting boat lights, it’s crucial to consider their wattage output or bulb type to ensure optimal visibility in dark environments.

Colored boat lights are often found on vessels and can come in white, blue, or red colors, each serving a specific purpose based on the laws at sea. White lights generally have a stronger output compared to other colors. Blue lights are more effective underwater, and red lights can mark specific areas within narrow channels, among other uses.

In addition to colored boat lights, reflective materials like tape can upgrade the common areas on ships, such as rails or posts. These materials help draw attention to the vessel’s proximity to other nearby ships and enhance safety.

Maintenance and Troubleshooting

Proper maintenance of boat light systems is crucial to keep operating costs low, especially when dealing with high-wattage fixtures commonly found in the marine environment. Regularly maintaining these systems throughout their lifespan is essential.

One critical maintenance aspect is storing boat lights properly during off-season storage periods. It is crucial to ensure that each unit remains dry. This storage is necessary to preserve their longevity and ensure their functionality when powered back on. Moisture buildup can lead to short circuits, malfunctions, and damage to the light’s components.

You should follow basic troubleshooting methods as part of routine maintenance. This maintenance includes cleaning off any corrosion and regularly checking bulb connections. These steps should become a natural course for anyone embarking on nighttime sailings or exploring uncharted territories.

Proper illumination is crucial for safe and legal boating at night. All boats need to have adequate lighting regardless of their size and capabilities. Following maritime laws and regulations related to navigational requirements and using the correct boat light format enhances safety for everyone on maritime travels. The mastery of navigation skills and adherence to these standards will continue to uphold the honor and legacy of future generations.

Article Contributors

Sail magazine review team.

SAIL Magazine Review Team reports on best-selling products in sailing and boating. SAIL Magazine is reader-supported: When you buy through links on our site, we may earn an affiliate commission. Artificial Intelligence (large language models) may have been used in the research and creation of the content.

To ensure questions about product testing or a specific article are addressed, please contact [email protected]

Sailboat Navigation Lights: A Guide to Safe Nighttime Sailing

by Emma Sullivan | Jul 26, 2023 | Sailboat Maintenance

==Short answer sailboat navigation lights:== Sailboat navigation lights are essential safety features that help vessels communicate and avoid collisions at night. These lights, such as the red and green sidelights and white stern light, allow sailors to determine the direction and status of approaching boats.

Understanding the Importance of Sailboat Navigation Lights

Sailing, with its air of romance and adventure, is a timeless pursuit that has captured the hearts of seafarers for centuries. While sailing enthusiasts revel in the sense of freedom and connection with nature that this activity provides, it is crucial to recognize that safety should always be a top priority when out on the open water. Among the many precautions taken to ensure safe navigation, sailboat navigation lights play an essential role.

These lights serve as beacons in the darkness, guiding both sailors and other vessels on their watery voyages. They are particularly vital during low visibility conditions such as fog, twilight, or nightfall when discerning a sailboat’s presence can be challenging. By understanding the importance of sailboat navigation lights, sailors can take proactive steps towards avoiding collisions and mishaps while enjoying their time at sea.

First and foremost, these lights serve as a communication tool between vessels. Just as traffic signals guide drivers on roads, sailboat navigation lights communicate a vessel’s navigational status to others nearby. These lights convey critical information about a boat’s direction of travel and whether it is under power or relying solely on wind propulsion. This enables other boats to predict potential collision courses and adjust their own paths accordingly.

In terms of regulatory compliance, having properly functioning navigation lights is not just recommended; it is required by international maritime laws like The International Regulations for Preventing Collisions at Sea (COLREGS). These regulations provide clear guidelines for different types of watercraft around the world to standardize safety measures. Following these rules ensures that every sailor speaks the same language when at sea, diminishing misunderstandings and encouraging mutual respect among mariners.

Furthermore, sailboat navigation lights contribute significantly to situational awareness – an invaluable asset in any seafaring endeavor. By displaying specific colors and configurations such as red/green sidelights and a white stern light visible from 135 degrees, sailors can discern the orientation of approaching vessels even in complete darkness. This knowledge empowers sailors to make informed decisions about altering their course or speed to avoid potential dangers.

In addition to enhancing navigation safety, sailboat navigation lights also add a touch of elegance and charm to nighttime voyages. Picture yourself sailing under a summer moonlit sky, with the soft glow of your vessel’s navigation lights casting mesmerizing reflections on the water’s surface. These lights not only provide reassurance but also create an enchanting ambiance for both sailors and onlookers.

While it may be tempting to dismiss the importance of sailboat navigation lights as just another cumbersome boat regulation, understanding their indispensable role is crucial for every sailor’s peace of mind and for ensuring uninterrupted enjoyment of our beloved pastime. So next time you set sail, remember that these little beacons serve as more than mere accessories – they are your allies in darkness, silently guiding you towards safe passages and unforgettable adventures on the open sea.

How to Properly Install and Operate Sailboat Navigation Lights

When it comes to sailing, safety should always be a top priority. And one of the essential safety measures on a sailboat is proper navigation lighting. Sailboat navigation lights help other vessels identify your boat’s position and course, especially during low visibility conditions or at night. In this blog post, we will guide you through the correct installation and operation of sailboat navigation lights to make your sailing adventures safe and enjoyable.

Installing sailboat navigation lights may seem like a simple task, but there are several key factors to consider for optimal functionality. First and foremost, familiarize yourself with international regulations regarding navigation lights. These regulations ensure consistency across different countries and improve communication between vessels on the water.

Before starting the installation process, carefully choose high-quality LED lights specifically designed for sailboats. LEDs offer numerous advantages over traditional incandescent bulbs, including energy efficiency, higher light output, longer lifespan, and reduced heat emission. Additionally, LEDs are more durable and resistant to vibrations commonly experienced while sailing.

To begin installing your sailboat navigation lights:

1. Determine the appropriate locations: Positioning your navigation lights correctly is crucial to maximize their visibility and effectiveness. Refer to your boat’s owner’s manual or consult with a marine electrician to identify the ideal mounting points for each light.

2. Prepare wiring routes: Plan out the wiring routes before drilling any holes or mounting fixtures. Concealing wires within the boat’s structure not only enhances aesthetics but also minimizes potential damage caused by exposure to external elements.

3. Drill strategically: Using an appropriately sized drill bit, carefully create mounting holes following the instructions provided by the manufacturer of your chosen navigation lights.

4. Connect electrical components: Install a waterproof junction box near each light fixture to protect wires from moisture and corrosion. Make connections following color-coded standards (red wire – positive; black wire – negative), ensuring proper polarity is maintained throughout the circuit.

5. Securely attach fixtures: Once all wiring connections are made, attach the navigation light fixtures to their designated mounting positions. Double-check that they are secure and properly aligned to maintain optimal visibility.

With your sailboat navigation lights installed, it’s time to understand their operation. Different situations call for specific combinations of lighting:

1. Underway with power: When sailing under engine power, display both a red (port side) and a green (starboard side) light visible from dead ahead to 22.5 degrees abaft each beam. A white stern light should also be shown.

2. Sailing without power: When solely relying on wind propulsion, display just the red and green sidelights in the same manner as during powered navigation.

3. At anchor: If you’re moored or anchored, only exhibit an all-around white light at a location high enough to illuminate unobstructed from every angle.

4. Restricted maneuverability: In situations where your sailboat’s maneuverability is impaired (e.g., towing another vessel), use three shapes—two balls vertically aligned above one diamond—to indicate restricted movement.

Lastly, always ensure proper maintenance of your sailboat navigation lights:

1. Regularly inspect for damage: Routinely check for signs of wear and tear on the electrical connections, housing seals, lenses, and reflectors. Replace any damaged components promptly.

2. Clean for maximum visibility: Keep lenses clean from dirt, grime, salt residue, or any other obstructions that could limit the effectiveness of your navigation lights.

3. Carry spare bulbs/batteries: Be prepared by carrying backup LED bulbs or batteries in case of failure during extended voyages.

By following these installation steps, understanding proper operation techniques according to maritime regulations, and maintaining your navigation lights diligently; you can cruise confidently knowing your sailboat is equipped with highly visible and functional navigation lighting system—an important feature enhancing safety while enjoying the open water at any time of day or night. So, set sail with peace of mind and navigate the seas safely while embracing the thrilling adventures that await you!

Step-by-Step Guide: Setting Up Sailboat Navigation Lights for Safe Sailing

Welcome aboard, fellow sailors! Today, we are going to dive into the nitty-gritty of setting up sailboat navigation lights for safe sailing. As you know, proper navigation lights are an essential part of ensuring your safety on the water, especially during low-light conditions and at night. So grab your cup of coffee, sit back, and prepare to learn how to illuminate the seas like a professional.

Step 1: Know Your Lights Before we jump into the technicalities, let’s familiarize ourselves with the different navigation lights required on a sailboat. These include the red port light on the left side, green starboard light on the right side, white stern light at the rear, and if our boat is longer than 20 meters (or 65 feet), a white masthead light at its highest point. Having this knowledge sets you up for success in navigating effectively while abiding by maritime regulations.

Step 2: Choose Your Lighting System Now that we’ve covered the basics, it’s time to decide which lighting system is most appropriate for your sailboat. You have two options: traditional incandescent bulbs or modern LED lights. While both serve their purpose well, LED lights are more energy-efficient and tend to last longer – a win-win situation!

Step 3: Gathering Materials To ensure smooth sailing throughout this process (pun intended), gather all necessary materials beforehand. This includes navigation lights (either incandescent bulbs or LED lights depending on your preference), wiring connectors, heat shrink tubing (to protect connections from moisture), electrical tape, wires (preferably color-coded for easy identification), wire strippers/cutters, and mounting hardware suitable for your boat.

Step 4: Planning Placement Consideration of placement plays a crucial role in setting up navigation lights effectively. Ensure visibility from all angles without obstructing other boat equipment or compromising aesthetics onboard. Take note of any manufacturer guidelines provided with your purchased lights for optimal placement. Remember, safety doesn’t mean sacrificing style!

Step 5: Wiring Your Lights Now we’re getting hands-on! Let’s start with the stern light. Attach the wires of your chosen light to the existing electrical system using appropriate connectors and ensure a secure connection. Utilize heat shrink tubing and electrical tape to safeguard against any moisture-induced malfunctions. Repeat this process for both port and starboard lights.

Step 6: Don’t Forget the Masthead Light If your sailboat exceeds 20 meters in length, you’ll need a masthead light too. Carefully mount this light on top of your mast using suitable hardware. Then, run additional wires through the mast to connect it securely with your electrical system.

Step 7: The Proof is in Testing After successfully wiring all navigation lights, it’s time for a crucial step – testing! Double-check that all connections are secure and operational before venturing out onto the open water. Be meticulous; don’t let a faulty bulb ruin your sunset cruise or impede your journey under a moonlit sky.

Congrats, sailors! You’ve now mastered the art of setting up sailboat navigation lights for safe sailing. Remember, maintaining these lights should be an essential part of regular boat maintenance as well. With proper illumination, maritime rules adhered to diligently, and cautious seamanship skills mastered, you can enjoy many breathtaking nights on tranquil waters without compromising safety. So go forth into the starry night with confidence and raise anchor towards new horizons! Bon voyage!

Frequently Asked Questions About Sailboat Navigation Lights, Answered!

Title: Frequently Asked Questions About Sailboat Navigation Lights, Answered!

Introduction: Navigating a sailboat safely and responsibly requires understanding and adhering to various rules and regulations. One vital aspect of sailing is ensuring proper use of navigation lights. These lights not only aid in visibility but also help communicate with other vessels on the water. In this blog post, we will delve into frequently asked questions about sailboat navigation lights, offering detailed professional answers infused with wit and clever insights.

1. Why are navigation lights necessary for sailboats? Navigation lights serve as visual signals that enable sailors to identify vessel types, positions, and movements at night or in low visibility conditions. They are crucial for promoting safety on the water by helping prevent collisions and aiding in the communication between boats.

2. What are the different types of navigation lights found on a sailboat? Sailboats typically feature three main navigation lights: red (portside), green (starboard side), and white (stern light). The red light tells other sailors that your boat’s portside is facing them, while the green light indicates that your starboard side is visible. The white stern light illuminates the rear of your vessel, making it easier for others to determine your direction of travel.

3. When should I turn on my sailboat’s navigation lights? According to international rules of collision avoidance at sea, all vessels must show proper navigation lighting between sunset and sunrise or during periods of restricted visibility such as fog or heavy rain showers. It’s essential to remember that even during daylight hours if visibility drops due to poor weather conditions, switching on navigational lights can greatly enhance safety.

4. Are there any additional requirements regarding sailboat navigation lighting? Yes! Aside from displaying the three main distinct navigation lights mentioned above, it is crucial for sailboats under power or motorsailing – using engine power alongside sails – to display an additional white forward-facing masthead light apart from the stern light. This masthead light helps identify the sailboat as a power-driven vessel, providing further clarity to nearby boaters.

5. Can I use LED lights for navigation purposes on my sailboat? Absolutely! In fact, LED lights are highly recommended for their energy efficiency and prolonged lifespan compared to traditional incandescent bulbs. However, it is essential to ensure that any LED navigation lights you use adhere to relevant maritime regulations concerning color, visibility range, and intensity.

6. How can I check if my sailboat’s navigation lights are working correctly? Regular maintenance and testing of your navigation lights are vital to guarantee their functionality when needed the most. Before every outing, visually inspect each light for signs of damage or corrosion. Additionally, switch on all navigational lights while docked or at anchor to verify they illuminate brightly according to the appropriate standards laid out in navigational lighting regulations.

Conclusion: Understanding sailboat navigation lighting not only ensures your safety but also promotes effective communication with other vessels on the water. By knowing when and how to properly utilize these lights, you contribute to maintaining a harmonious sailing environment. Remember, navigating with wit means being informed and cleverly enhancing your skills as a sailor while keeping safety at the forefront of your adventures!

Top Tips and Best Practices for Maintaining Sailboat Navigation Lights

Maintaining Sailboat Navigation Lights: Expert Tips and Best Practices

Picture this – you’re out on the open water, gliding along with the wind in your sails. As the sun dips below the horizon, darkness begins to envelop your sailboat. This is when maintaining proper navigation lights becomes paramount for both safety and legal compliance. In this blog post, we will dive deep into top tips and best practices for ensuring that your sailboat’s navigation lights are not only functioning but also showcasing their brilliance.

1. Regular Inspections are Key: To ensure your sailboat navigation lights are in prime condition, regular inspections should be conducted. Make it a habit before every trip to thoroughly examine all lights, from bow to stern. Look out for any loose connections, cracked lenses, or water intrusion that could hamper their effectiveness.

2. Ensure Proper Power Supply: One common issue faced by sailors is inadequate power supply to navigation lights, leading to dimness or complete failure at crucial times. Check that the wiring system is correctly connected and working optimally. Additionally, consider installing a voltage monitor or battery analyzer to keep tabs on power levels during extended journeys.

3. Choose LED Lights: When it comes to choosing sailboat navigation lights, opt for LED technology without hesitation. LEDs offer brilliant luminosity while consuming minimal power compared to traditional incandescent bulbs. Their longevity and durability make them ideal for equipping your vessel’s masthead light, sidelights, stern light, and anchor light.

4. Cleaning is Essential: Navigation lights on a sailboat accumulate dirt and grime over time due to exposure to various elements like saltwater spray or bird droppings (we all know how seagulls love making our boats their restroom). Regularly clean the lenses with a soft cloth and mild soap solution followed by drying with a lint-free towel. Keeping them crystal clear will maximize their output and visibility range.

5. Protect Against Moisture: Water ingress can be a persistent menace, harming the functionality of your sailboat’s navigation lights. To combat this, ensure watertight seals around light fixtures and wiring connections. Applying silicone lubricant or dielectric grease to connectors further enhances protection against moisture.

6. Carry Spare Bulbs and Fuses: Murphy’s Law states that anything that can go wrong, will go wrong – especially in the middle of nowhere. Imagine how disheartening it would be if one of your navigation lights suddenly fizzles out on a moonless night! Always carry spare bulbs and fuses suited for your specific lighting system to avoid such predicaments and keep your journey uninterrupted.

7. Stay Familiar with Navigation Regulations: Being updated on marine regulations regarding navigation lights is not only essential for your safety but also ensures compliance with local laws. These regulations dictate the placement, colors, and timings for displaying navigational lights based on different conditions such as underway, anchored, or sailing near other vessels at night.

In conclusion, maintaining sailboat navigation lights might seem like a mundane task; however, its significance cannot be undermined when it comes to safety during nighttime voyages. Regular inspections, adequate power supply, LED technology adoption, cleanliness, moisture protection, carrying spare bulbs/fuses, and adhering to maritime regulations should become second nature for any seasoned sailor. By following these top tips and best practices meticulously, you’ll be able to navigate the vast expanse of dark waters with confidence while ensuring a safe voyage each time.

Exploring Different Types and Designs of Sailboat Navigation Lights

When it comes to sailing at night, having the right navigation lights on your sailboat is absolutely crucial. Not only do they help you stay safe and avoid collisions with other vessels, but they also ensure that you are compliant with maritime regulations. In this blog post, we will be exploring different types and designs of sailboat navigation lights, so you can make an informed decision for your own vessel.

One of the most common types of sailboat navigation lights is the sidelight. These lights are usually mounted on either side of the boat and emit a green light on the starboard (right) side and a red light on the port (left) side. The purpose of these lights is to signal the direction in which your boat is moving to other vessels in the vicinity. Additionally, sidelights should be visible at a distance of at least two nautical miles, ensuring that other boats have ample time to react accordingly.

Another important type of navigation light for sailboats is the sternlight. As its name suggests, this light is mounted at the back or stern of the boat and emits a white light. The sternlight helps other vessels determine if you are moving away from them or approaching them from behind. It should be visible from a distance of at least two nautical miles as well.

In addition to sidelights and sternlights, sailboats also require an all-round white light, commonly known as an anchor light. This light serves as both an anchoring indicator and a warning signal to other boats that your vessel isn’t under power and may be stationary. Typically mounted atop the mast or another elevated point on the sailboat, this white light must be visible from all directions within two nautical miles.

Now that we’ve covered the main types of sailboat navigation lights, let’s delve into their designs. While traditional incandescent bulbs were once widely used for their simplicity and affordability, LED technology has revolutionized marine lighting. LED navigation lights are highly energy-efficient and have a considerably longer lifespan compared to incandescent bulbs. Additionally, LEDs emit a bright and focused light, making your sailboat more visible to others even in adverse weather conditions.

Furthermore, many LED navigation lights come with built-in features that enhance safety and convenience. Some models have automatic sensors that adjust the brightness of the lights depending on the ambient lighting conditions. This means that if you’re sailing during twilight or dawn, when visibility is reduced, these lights will automatically become brighter for better detection by other vessels.

Moreover, some innovative designs include combination lights that incorporate both sidelights and sternlights in one compact unit. These multifunctional lights save space on your boat while still ensuring compliance with regulations. Additionally, there are folding or telescopic navigation lights available that can be easily stowed away when not in use, further optimizing your deck space.

In conclusion, choosing the right types and designs of sailboat navigation lights is crucial for safe night sailing and regulatory compliance. Sidelights, sternlights, and anchor lights are essential components of any sailboat’s lighting system. Consider opting for energy-efficient LED technology that offers enhanced visibility and longevity compared to traditional incandescent bulbs. Moreover, explore innovative designs such as combination lights or folding options to optimize space onboard your vessel. By equipping your sailboat with the right navigation lights, you can navigate confidently through the darkness while captivating other sailors with your illuminated elegance on the open sea!

Recent Posts

• Sailboat Gear and Equipment
• Sailboat Lifestyle
• Sailboat Maintenance
• Sailboat Racing
• Sailboat Tips and Tricks
• Sailboat Types
• Sailing Adventures
• Sailing Destinations
• Sailing Safety
• Sailing Techniques

Navigation Lights

• You are required to display the appropriate lights at night or during times of reduced visibility.

Navigation lights are used to prevent collisions at night or in times of reduced visibility, and are an essential tool in keeping you and your vessel safe. Nav lights allow you to see other nearby vessels, and allow other vessels to see you.

Nav lights also provide information about the size, activity, and direction of travel. By understanding the characteristics of Nav lights, you can determine an appropriate course of action as you approach another vessel.

On any vessel, navigation lights have a specific color, (white, red, green, yellow, blue), arc of illumination, range of visibility, and location, as required by law and regulations. For the purposes of this course, we will concentrate on pleasure boats under 65 feet in length. Knowledge of navigation lights is important to a small-boat skipper for separate, but important, reasons.

• You are legally responsible for displaying lights of the proper color, intensity, location and visibility on your boat.
• Knowing the type and heading of another boat.

Legal Requirements

Vessels are required to show the proper navigation lights from sunset to sunrise in all weather conditions, good and bad. During these times, no other lights that could be mistaken for lights specified in the Rules of the Road can be displayed, nor any lights that impair the visibility or distinctive character of navigation lights, or interfere with the keeping of a proper lookout. The Rules also state that navigation lights must be shown in conditions of reduced visibility, and may be shown at other times considered necessary.

It's Your Responsibility

It is the responsibility of the owner/operator of a vessel that she show the proper navigation lights for her size and the waters in which she is operating. It is not the responsibility of the manufacturer, importer, or selling dealer. Many boats are delivered with lights that do not meet legal requirements with respect to technical characteristics or placement on the vessel. Remember also, that the angles of visibility must be met when the boat is underway-if your boat rides at a significant bow-up angle, take that into consideration when installing and/or checking your lights.

Navigation Lights for Powerboats

Power driven vessels underway shall exhibit a masthead light forward, sidelights and a stern light. Vessels less than 12 meters in length may exhibit an all around white light and side lights. Power driven boats on the Great Lakes may carry an all around white light in stead of a second masthead light and stern light combination.

Sidelights - Colored lights - red on port and green on starboard - showing an unbroken arc of the horizon of 112.5 degrees, from dead ahead to 22.5 degrees abaft the beam on each side.

Combination lights - Sidelights may be combined in a single fixture carried at the centerline of the vessel.

Stern light - A white light showing over an unbroken arc of the horizon of 135 degrees, centered on dead astern.

Navigation Lights for Sailing

A sailing vessel of less than 7 meters in length shall, if practicable, exhibit regular navigation lights, but if not practical, she shall have ready at hand an electric torch or lantern showing a white light which shall be exhibited in sufficient time to prevent collision.

Diving Lights

Another light display that you may see in resort areas, or waters that have wrecks or reefs, is the night diving configuration. This has three vertical masthead lights, that have a red-white-red sequence. You must maintain a good distance from these vessels, and you should also be aware that there may be divers near you.

Interpreting what you see

It's great that you're learning the basics of lights - what is required and when they're required. But, this in only the beginning. You must also learn how to interpret the navigation lights that you see when you are underway at night- and for your safety-learn it well.

For instance, if you see a vessel approaching that shows a light pattern such as the ones to the right, you immediately know that you are in a crossing situation, and that you must yield to the other vessel - that's why it is red.

Seeing a green light over a white light indicates a fishing vessel actively trawling. You not only need to avoid the vessel, but you also need to remember that it could potentially have a very large net deployed that you will also need to avoid.

And there are numerous other lights and combinations of lights that you must be able to instantly recognize - the lights for a sailboat that is privileged over a motorboat, the special lights of various fishing vessels, a dredge or a vessel not under command. Study the requirements for navigation from the viewpoint of a "looker" as well as a boat owner.

Yachting World

• Digital Edition

Night sailing: top tips and expert advice to see you safely through until dawn

• Helen Fretter
• October 6, 2016

A Yachting World special report on how to prepare and enjoy sailing at night. Photos by Tor Johnson.

Sailing through the night brings its own rewards: a contemplative stillness, phosphorescent trails through a star-lit sea, the soul-warming sunrises. But it also raises challenges – if you cannot see gusts and squalls approaching, how quickly can you react? How well do you – and the rest of your crew – know your yacht’s layout in the dark?

We asked some experienced long-distance cruisers, many of whom have sailed extensively in the tropics – experiencing much longer hours of darkness than northern hemisphere sailors who only venture offshore in summer months – for their night sailing advice.

Sundowner readiness

Romantic though sailing into the sunset may be, heading into darkness requires careful preparation. ‘Bones’ Black, who owns and skippers Emily Morgan , a Bowman 57 charter cruiser, says: “We do a great deal of night sailing, be it from island to island in the Caribbean or transatlantic passages. When doing overnight island-hopping we plan to arrive at the next destination in daylight, especially if we have not been there before.

“We prep the boat, all sail covers off, halyards attached, engine checks and of course we recheck the weather – if we are in tidal waters we would double check the tides too. We also prepare the cockpit by putting a good torch, hand-bearing compass, binoculars, bottle of water and spare safety tether to hand.

“Then we sit and have a decent meal to relax before we set sail. We also prepare a meal for later as it’s common to feel a little queasy at the start of a passage if it’s a bit lumpy and the last thing you want is to go below to start cooking.”

Erik Lindgren, currently cruising his Baltic 56 in Fiji, says: “ Spirit V is by design a very fast boat. This means that we cover good distances without pushing and without using too much sail at night. Our night set-up includes bimini down, sprayhood up, one or two reefs in the main depending on the risk of squalls, lifejackets are worn and we are always clipped on, AIS transmitters in lifejackets and PLB in foulweather jackets.”

Paul Frew, who is sailing his Oyster 575 Juno around Europe with his wife Caroline, says: “We are very cautious offshore. We have a golden rule never to leave the cockpit at night, so we will delay a pole gybe until daylight even it means heading a few miles off course. If for any reason we do need to leave the cockpit the on-watch crew have to call me and we all clip on. “I have an offshore checklist that we always review before any night passages. I keep a high-powered 24V torch in the cockpit and an anti-collision flare in the companionway. Radar is always on at night and AIS alarms are checked before dark.”

Take extra precautions if heading out of the cockpit on to the foredeck when sailing at night.

Golden rules

Once underway every skipper applies the same golden rules, summed up by Will Downing, skipper of the Hanse 575 Ximera : “Lifejackets obligatory; lifelines attached even if you are sleeping in the cockpit; don’t go forward without someone else awake in the cockpit and clipped on.”

Erik Lindgren adds: “We never, ever leave the cockpit while on a single watch. Sail area is reduced during the night – if hit by a big squall – by furling the jib. The off-watch sleeps on the saloon sofa.”

John Dyer, who sailed his First 47.7 Exocet Strike on the World ARC, says: “While on night watches we always take a view on likely weather conditions and reef accordingly before it’s dark – always easier to shake reefs out than put them in. “We also use head torches and use the red LED to preserve night vision.”

Top tip: Night vision relies on rod cells in the eyes, which take 20-40 minutes to adapt to a change of light

Bones Black says it’s also important to brief new crew joining the yacht on what to do if they have concerns. “We tell our crew always to wake Anna as skipper or me as first mate at any time. I would rather get up and check something out, be it a strange noise or a light on the horizon in good time, rather than at the last minute when it could be a problem.”

Conversely, when all is going well, being considerate of your off-watch crew is important – tether hooks dragging on deck and rattling pans in the galley sound incredibly loud at night. If you need to run a generator, consider timing it so it so the noise is split over two watches.

Sailing at night can be a truly uplifting experience.

Watch patterns

Your choice of watch system depends on several factors – how many people there are on board, how mentally and physically draining the conditions are, and personal preferences – some people find it hard to sleep down below during the day, for instance, while others prefer a short night watch and a longer day off-watch.

Fact: NASA studied the sleep patterns of solo ocean racing sailors to see how extreme sleep deprivation affects decision making and performance.

Will Downing comments: “I am a firm believer in the four-hour sleep rule of REM. Most people sleep for four hours, then two hours, then one hour, with waking moments (or close to) in between. If there are only three people on board, a three-hours-on six-off watch system means you will definitely get that four hours of sleep. Two hours on and four off is not four hours of sleep. Once you’ve brushed your teeth, had a snack, gone to the heads and maybe read for a few minutes, you’re lucky if you end up with just three hours.

“Even better is a four-person shift pattern with two hours on and six off. It’s not long on duty, but long on the old shut-eye. I have always found that the crew are better humoured, easier going and just plain happier!”

Black agrees: “There are so many different watch systems you could run, but they depend on how many crew you have. If it’s just Anna and me we do three on and three off during the night, and four on four off during the day to catch up. If alone on watch we steer for about 20 minutes, looking around the horizon all the time, then have a look at the AIS and radar.

“If there are three people we do three on, six off and steer as much as we can to keep busy. When concentration starts to lapse the autopilot goes on for a while and a drink and a few nibbles help.

“If we have a full complement of six crew we run three on, six off with two crew on each watch, this means the crew on watch can steer for half an hour then swap.”

For an even more in-depth look at this topic and plenty of others, see our Bluewater Sailing Techniques feature and video on night watches and routines offshore

Handover period

Equally important is how you hand over between watches. Downing says it’s worth taking your time over the watch change. “When you finish a shift in the middle of the night and are yearning for your pillow and some well-earned rest, remember that the person coming on watch has only just recently woken up so take time to chat with them, offer them a hot drink, talk about the weather and the shipping.

“I always finish with asking: ‘Are you awake enough to do this?’ Remember that your life is now in their hands!”

For the person coming on deck Downing suggests: “Read the log. It’s nice to know they saw dolphins and a mermaid, but more important that they heard a rattle from the engine or that the temperature felt like it dropped several degrees very quickly.”

Preserve your night vision but keep on top of the logbook, radar and navigation

Getting through it: Creature comforts to get through the night

“As we normally have three or four crewmembers on long passages we adopt a mother watch. Desert Island Discs downloaded from the BBC is our favourite distraction!” Paul and Caroline Frew, Juno

“Listening to music helps pass the time – but I am always being told off by Anna for singing along while she is trying to sleep. We also have what we call the ‘excessive calories box’ stuffed full of sweets, breakfast bars, chocolate bars and anything else we can find. There is nothing like the sight of your watch mate appearing at 0300 with the box to raise morale.” Bones Black, Emily Morgan

• Articles and Guides

Sailing at Night: Top Tips

30th jan 2018 by samantha wilson.

If you’ve never sailed at night then you’re really missing out on one of the most magical and soulful sailing boat experiences possible . The stillness of a star-lit sea on a cloudless night can be a contemplative adventure that distills the very essence of pure sailing.

However, it does raise challenges. How well do you know your yacht’s layout in the dark? How do you anticipate the squalls and gusts if you can’t see them?

In this guide, we’ll look at a few hints and tips to help make your night sailing experience safe and secure .

Night Vision  while Sailing

• If you’ve been wearing sunglasses all day, allow up to 40 minutes for your eyes to adjust to the dark . Night vision relies on rod cells in the eyes. They can take 20-40 minutes to adapt to darkness.
• Ensure your navigation screens are dimmed and turn off any unnecessary light-emitting electronics .
• Use a red bulb in your flashlight if possible. If you’re using a white bulb then avoid shining the light directly at the rig, as the reflected light will destroy your night vision.

Food and Clothing while Sailing at Night

• Don’t forget that no matter where you are sailing, it always gets cooler at night to ensure that you wear adequate warm and dry clothing.
• Store hot drinks and food within easy reach of the cockpit.

Safety Equipment while Sailing at Night

• Ensure all crew members wear a lifejacket and harness whenever they are on deck at night. Make sure everyone is aware of the clip-on points and jackstays. Even if you are sleeping in the cockpit, don’t go forward without someone else clipped on and awake in the cockpit.
• Review your man overboard procedures and ensure the light is attached to the horseshoe/DAN buoy. Check before you commence the voyage.
• Any crew member on watch should be equipped with a red bulb flashlight, a knife, and a personal EPIRB/AIS locator.
• Ensure that all gear is carefully stowed away. Set up lee cloths and check that all seacocks that need to be closed are closed.
• Test any communication equipment before leaving.

Night Watch while Sailing at Night

• Set up a clear watch schedule to ensure all crew members have adequate rest and breaks. If there are only three people on board, a three hours on-six off watch system will ensure all crew has adequate rest time whereas a four-man crew could operate on two hours on four hours off system. Brief your crew thoroughly to ensure that everyone knows and understands the watch system and what your expectations are.
• Make all crew members aware that they could be called onto the deck at anytime.
• Never post an inexperienced crew member on watch alone. Pair them up with a more experienced member of the crew.
• The retiring crew should give the new watch a briefing on sea and weather conditions, hazards or traffic in the area, and any relevant information as to the state of the boat. Remember the crew member taking over the watch may have only just woken up. Ensure they are awake enough to carry out the watch- your life is in their hands!
• Rest. Don’t be tempted to stay up all night star-gazing on deck. Even if you don’t sleep, rest in your berth to ensure you are fresh and awake for when it’s your turn on watch. Set an alarm for about 15 minutes before your watch period is due to begin and get some food and drink.
• Be considerate to your off-watch crew. Tether deck hooks and rattling pans in the galley; sound travels farther on a still night. If you’re running a generator, consider timing it to be split over two shorter watches rather than over one long watch. Alternatively, charge batteries in the afternoon and watch your power consumption so you don’t need to use the generator at night.
• Don’t get lost in a book whilst on watch. Keep your head on a swivel and simply enjoy the experience of steering the boat and the sights and sounds of the night. Scan the horizon every 10 to 20 minutes. Check the radar and AIS and make proper log entries.

Seamanship at Night

• It’s a good idea to make your first night sail in familiar waters with a full moon to aid visibility.
• Under Rule 25 of the International Regulations for Preventing Collisions at Sea , a sailing vessel must exhibit both red and green sidelights and a white sternlight. The craft under 20 metres can combine the prescribed lights with a tricolour lantern near the top of the mast.
• Rule 23 states that a sailing vessel under power must exhibit sidelights, a sternlight, and a white masthead/steaming light forward. Make sure your ensign isn’t draped over the stern light. Test all lights before leaving and make sure you carry spares for all lights.
• Identify any navigation marks that have light characteristics using your charts. For quick reference, make a note on your passage plan the sequence of expected lights. Work out a clear bearing from the navigation lights and make a note on your passage plan to avoid hazards. Plot a series of GPS waypoints and use the “navigate” function to follow a reference guideline.
• Although it is easier to see other vessels at night, it is also easy to confuse the distances involved. Assess a vessel’s intentions by keeping a good watch and adjust your path accordingly. Keep a close eye on your radar and AIS but don’t rely on them solely. Fishing boats tend to have unpredictable movements and lights so be vigilant when on watch.
• Don’t run at 100% . Most skippers operate at 80% capability at night. This will help minimise any disruptions and will ensure a comfortable ride.
• Base any sail adjustments to be made by each watch on your crew’s experience.

Written By: Samantha Wilson

Samantha Wilson has spent her entire life on and around boats, from tiny sailing dinghies all the way up to superyachts. She writes for many boating and yachting publications, top charter agencies, and some of the largest travel businesses in the industry, combining her knowledge and passion of boating, travel and writing to create topical, useful and engaging content.

More from: Samantha Wilson

Related Articles and Guides

5th Sep 2024

Hurricane Preparation: Plan to Keep Your Boat Safe

30th Aug 2024

10 Steps to Launch Your Boat Safely from a Trailer

18th Jun 2024

How to Dock a Boat with Joysticks, Single Engines, and Twins: Tips and Technique...

20th May 2024

Essential Boat Safety Tips for Every Type of Watercraft

• Explore Rightboat
• Boats for Sale
• Boating Articles
• Buyers Guide
• About RightBoat
• Sell Your Boat
• Boat Selling Advice
• All manufacturers
• All categories
• Are you a broker/dealer?
• Learn more about the Rightboat:HUB

Enter your email to keep up to date with the latest news

Join for free

Sign up now for free and discover how easy it is to keep up to date with THE latest boats for sale. Find your right boat, and tailor your voyage to finding your next boat.

Benefits of becoming a member:

• Set up tailored alerts
• Personalise your experience
• Download full specifications and broker details
• Keep tabs on your favourite boats

Are you a broker? Join as a Broker

Rightboat - join for free.

Do you have an account already? Login

Save this search

Save your search and receive new boats in your email..

You can unsubscribe from your alerts whenever you like. By pressing the button you accept the Legal Terms and conditions

• How to sail at night

Captains are often asked if it's possible to sail at night. In the vast majority of cases, the answer is yes, unless you are just starting out. You just need to know the specifics of night sailing — the rules of boat lighting, beacon signals, have navigation and nautical charts handy, and most importantly, follow basic safety rules on board. So, do you know what night sailing entails?

You can't do it without the correct lights

While on land, lights are primarily there to help us see, at sea it's the other way around. All boats must be properly lit for other vessels to see. And, a boat doesn't work like a car either, where we shine our headlights on the road ahead to see what's in front of us. At sea we rely on navigation, nautical charts, lighthouses and the captain's knowledge.

Basic boat lights include running lights, steaming lights and anchor lights. There are clearly defined and standardized rules for lighting a ship  under sail at night . So the question of how to light a yacht at night has a very simple answer. Running lights, or side lights, show other vessels where your port and starboard sides are, with red indicating port and green starboard, and you must also have a white stern light on.

Lighting the yacht at night is very important because, unlike during the day, the helmsman cannot judge the distance and direction  of other boats by sight. Running lights make the position and direction of the surrounding vessels visible, as well as their approximate distance, and helps to avoid possible collisions. Radar is also highly practical in this respect, as it shows the size and distance of the vessel.

However, when sailing there can be situations where the sails need to be lowered, and with that, the lighting also needs to be changed. If travelling under motor power , a steaming light  (masthead light)  must be turned on , which shines at the same angle as the side lights. When a sailboat is not under sail, it has to abide by the rules set out for power boats by COLREG (The International Rules for Preventing Collisions at Sea).

Lighting regulations when at anchor are again different. When at anchor at sea , only the anchor light should be on . According to the regulations this could be either a 360-degree white light atop the mast, or a light suspended from the boom, above the foredeck or on a furled genoa. If the boat is moored in port, the light is not normally used.

Navigation, GPS and maps

Nowadays, GPS and navigation aids integrated into the boat or that work as mobile apps are commonly used to determine the position of the boat. Modern technology is very accurate and reliable, but it is still worth understanding, reading and checking your position on  paper nautical charts . After all, almost any skipper will tell you that their GPS or navigation system has at some point told them they were on land, even when tens or hundreds of metres from shore.

Thanks to nautical charts, you will not only know of possible danger spots, but also lighthouses , enabling you to easily and accurately determine your position with the help of a compass. Each lighthouse is different, being lit and flashing in a unique way. A nautical chart will tell you how to identify a lighthouse by the number of flashes, their frequency and the colour of the light. To determine your exact position, you’ll then need two lighthouses in sight that serve as reference points for each other.

YACHTING.COM TIP: Lighthouses are not only practical, but they are often buildings with impressive architecture that are well worth stopping off at. Take a look at  15 lighthouses you must visit .

Safety is paramount when sailing at night

Even during the day, there are clear rules regarding the movement of the crew on board. Basically, the crew should not stand unless they are engaged in manoeuvres. In all other cases, they should be sitting on benches, at the side of the boat when heeling, or in the cabin. Apart from the fact that a standing crew member could obstruct the helmsman's view, it also poses a greater risk of falling overboard . If you're interested in getting to know this subject in more detail, check out our article Sailing Etiquette A to Z .

At night, the rules are even stricter to ensure the crew remain as safe as possible and avoid damaging the yacht. If a crew member is on deck at night while sailing, they should wear a lifejacket  and ideally be attached to the boat with a lifebelt or harness.

Except for really experienced seafarers, the rule of thumb is that there should be at least  two people on board when sailing at night. And the captain should schedule shifts so that there are always two  rested crew members on board. After all, you need to be doubly vigilant when sailing at night, and staying awake all night is certainly not conducive to alertness — especially when manoeuvring  or entering port. For the same reasons alcohol is prohibited when night sailing. While during the day, crew members other than the helmsman can toast Neptune or have one glass of wine or beer, drinking alcohol is not permitted during a voyage at night. By all means celebrate a successful journey upon arrival in port at a local tavern, but it definitely pays to keep a clear head at sea.

Specifics of night sailing and boat handling

Steering and controlling the boat  is not particularly different during the day and at night. There are just a few nuances to make sailing that bit smoother. If you're on a vessel you know well, that’s one thing, but if you're on a charter boat , it's worth marking the sheets and other lines so that you know your way around in the dark.

Sailing at night, it is also important to assess  the weather conditions well. What you would normally do during the day can be significantly more challenging at night and requires a more careful assessment of weather conditions and weather patterns. It is always better to choose smaller sails and if you have even the slightest doubt about anything, postpone the trip. 

When  entering a harbour  or sailing close to shore, be doubly cautious. There are several risk factors. During the day, the surrounding boats, the rocks and the potential hazards on the surface and below are visible. At night you have to rely on navigation, charts and lighting. When entering the harbour, charts and GPS can provide you many clues but lights can cause issues. For example, you might get dazzled by the light from the shore, the anchor lights of other boats are easily confused with the lights on land, and, last but not least, you may encounter poorly lit fishing boats. However, if you keep in mind all of these potential risks, you will arrive safely in the harbour.

The magic of night sailing

When compared to sailing during the day, night sailing places more demands on the captain's experience and knowledge of sailing regulations. But it is also a truly romantic experience. Millions of stars glistening in the night sky and the waves sparkling in the moonlight. If you're lucky, sailing out of the mist from land on a clear night with a near full moon, it will seem almost like daylight.

If you're serious about sailing and steering your boat, there are other benefits to night sailing. Navigating at night sharpens the senses and enhances the sailing experience as well as your experience of the sea itself. It truly gives a whole new meaning to sailing. But if all you want is to just enjoy yourself, night sailing is one of the most romantic experiences you can have. Check out our article on how to enjoy romance on board a yacht charter .   

Are you new to the sea? We will recommend experienced captains who will take care of you on the ship. Give us a call.

Denisa Kliner Nguyenová

Faq how to manage a night sailing.

Boat Lights At Night (The Rules For Safety)

Boat navigation lights at night are used for safety. They are designed so they can be seen easily. Boat lights vary according to boat type and size, boat use, navigation area, and geographic location. Boaters should learn boat light meanings and keep up-to-date on boat light requirements.

Boat navigation lights indicate a boat’s heading (Aspect) and what it’s doing. The boat’s red and green lights show the boat’s port and starboard sides. Let’s explain boat light type, actions, and requirements in detail.

Types of Boat Lights

Boating safety starts with proper boat navigation lights. If you are a boater, it’s important to understand the 4 types of common navigational lights on your vessel so that you can be seen by other boats in the water and avoid accidents or running aground.

Boat navigation lights are split into four groups. There are Sidelights, Stern light, Masthead light, and All-Round light.

Sidelights show Red or Green to other vessels approaching from the side or head-on, while stern light only points out white light when you’re coming up behind someone else’s boat.

Masthead light should be mounted high on a vessel’s aft-most part of the structure that extends above deck level. The masthead light is a requirement on all power-driven vessels. It shines forward and to both sides and the color of this light is white.

The boat’s all-around white light is on the mast, stern, or somewhere else on the boat. This light can act as an anchor light when a boat is anchored.

Boat Navigation Light Color

• Masthead light color – White
• Port sidelight color – Red
• Starboard sidelight color – Green
• Stern light color – White
• All-Round light color – white

Boat Light Visibility Range (Minimum)

• Side lights; Boat < 12m (39.4 feet) – At least 1 NM
• Masthead light; Boat < 12m (39.4 feet) – At least 2 NM
• Stern light; Boat < 12m (39.4 feet) – At least 2 NM
• All-Round light; Boat < 12m (39.4 feet) – At least 2 NM
• Boat < 20m (65.7 feet) – Masthead light at least 3 NM; Other light at least 2 Nm
• Boat > 20m (65.7 feet) – Masthead light at least 5 NM; Other light at least 2 Nm

Boat Navigation Lights Indicate W hich Side ?

Your boat’s navigation lights will basically tell you what side of the vessel is a port and which side is starboard. The red light indicates a vessel’s port (left) side; the green indicates a vessel’s starboard (right) side. Stern light is seen only from behind or nearly behind the vessel. Masthead Light shines forward and to both sides.

What Are Boat Lights Used For ?

Boat lights are typically used to guide boaters at night, but they can also be used for a number of other purposes. They can help you and other boaters determine which is the give-way vessel when encountering each other on the water during periods of restricted visibility such as fog or rain. So never forget boat lights at night — boat lights make you and others visible at night on the water. They are used only for boat safety purposes.

Boat Lights and The Law

To navigate safely in the water, vessels are required to show proper navigation lights. There’s no need to worry about boat lights being an inconvenience because they must be displayed from sunset to sunrise and during periods of limited visibility.

You must turn on boat lights when underway between sunset and sunrise, as well as during any period of restricted visibility such as fog, rain, or heavy snowfall. And when it is deemed necessary by any boat skipper, boat lights must be turned on during the day.

Why Do Boats Have Blue Lights?

The reason boats have blue lights is to signify that they are law enforcement vessels. They may display a flashing blue light when engaged in direct law enforcement or safety activities, so as not to interfere with the visibility of their navigation lights.

What Does a Single White Light on a Boat Tell You?

When you see a single white light on the horizon, it may mean that you are overtaking another vessel. In order to avoid collisions and other mishaps, give way to either side of the boat. Also, one single white light could mean that the other boat is at anchor.

What Does a Red Flashing Light Mean on a Boat?

A red flashing light means that it’s a WIG boat.

What Size Boat Requires a Stern Light?

If your boat is 39.4 feet or longer, make sure to get a separate masthead light and stern light. However, If you’re on a power-driven boat less than 39.4 feet in length, then the masthead and stern light may be combined into a single all-round (360 degrees) white light. 

Where to Put Navigation Lights on a Boat?

• Masthead – over the centerline of a boat (seen ahead from 225 degrees)
• Stern – near the stern, lowest height on a boat (seen 135 degrees from behind)
• Side – port/left side and starboard/right side (112.5 degrees sides arc)
• All-round – over the centerline of a boat (360 degrees arc)

Safety Tips When Using Boat Lights

– Must be turned on when underway between sunset and sunrise

– Should be turned on when in poor visibility

– Must be turned on when deemed necessary

– Must be mounted in such a way that boat lights are not obscured by any other obstructions

– Used for boat safety only

– Can never be used as floodlights

– Must be mounted in such a way that the other boat operator can see them clearly

– Should be properly illuminated at all times

– Must be mounted securely

– Must never be covered by boat covers or other obstructions

– Should be turned off when a boat is at anchor (Turn on anchor light)

Boat lights are more than just a way to see where you’re going at night. They can be used to communicate with other boats, and they can help you avoid collisions.

Boat lights are essential for safe night boating. They help other boats and vessels see your boat, and they also help you see where you’re going. There are different types of boat lights available, and it’s important to choose the right ones for your vessel.

What Are the Most Popular Boat Lights?

Here’s a look at some of the most popular boat lights and what they offer.

LED Boat Lights: LED boat lights are becoming increasingly popular due to their energy efficiency and long lifespan. They’re also much brighter than traditional incandescent bulbs, making them ideal for night boating. Many LED boat lights come in waterproof versions, so you don’t have to worry about them getting wet if you encounter rough waters.

Solar Boat Lights: Solar boat lights are a great eco-friendly option since they’re powered by the sun. They typically have built-in batteries that store solar energy during the day so that the light can shine at night.

Battery-Powered Boat Lights: Battery-powered boat lights are another popular option, especially for smaller boats. These lights typically use either disposable or rechargeable batteries, depending on your preference. Some battery-powered models even come with solar charging capabilities, so you can keep them charged even when there’s no sun available.

What Lights Should Be on When Boating at Night?

There are many different types of lights (including navigational lights) that are required or recommended to be used when boating at night. The type of vessel, the size of the vessel, and the area in which the vessel is operating will all play a great role in what specific lights need to be used. In general, however, there are a few basic rules that apply to all kind of vessels.

All these requirements exist so that other boats can easily identify your vessel and know its intentions (whether it is stopped, coming towards them, or moving away). By following these simple guidelines you can help keep everyone safe on the waterway.

Which Side of a Boat Has a Red Light at Night?

The side of a boat with a red navigation light at night is the port side. The port side is the left side of the boat when you are facing forward.

When Boating at Night What Does a Single Green Light Mean?

When you see a single green light, be sure that you are approaching a sailing vessel. In this case, you have to take action and you must give way. Remember, A sailing boat is always the stand-on mode except when it is going to overtake you.

What Lights are Required on a Boat at Night in Florida?

In Florida, boaters are required to display a white light visible in all directions from sunset to sunrise. Boats must have a white light visible from 360 degrees whenever they are safely moored or anchored away from jetty.

Leave a Comment Cancel reply

Save my name, email, and website in this browser for the next time I comment.

• BOAT OF THE YEAR
• Newsletters
• Sailboat Reviews
• Boating Safety
• Sails and Rigging
• Maintenance
• Sailing Totem
• Sailor & Galley
• Living Aboard
• Destinations
• Gear & Electronics
• Charter Resources
• Ultimate Boating Giveaway

Sailing at Night: Can You See in the Dark?

• By Teresa Carey
• Updated: October 16, 2014

The sun is just about to touch the horizon and you’ve spent the last hour setting up extra safety precautions for night sailing. You’ve connected a strobe light to your MOB ring. Every crew member on deck is wearing a harness and PFD with a light and whistle. And you’re showing the proper navigation lights to comply with the rules of the road. Every chart you’ll need this evening has been pulled from the locker, your course is plotted and lights you’ll see along the way have been listed. With your hand bearing compass and parallel rules, now you’re prepared to navigate — but under the dark cloak of night, how will you see?

At night, when visibility is compromised, sailors rely on all their senses to understand where they are and how the boat is moving. While we tune in our ears to listen for bells, breaking waves and horns, we sometimes forget that with an understanding of our vision and how it works at night, we can use techniques to help us adapt to the dark and see more than we thought possible.

Developing Night Vision When we step outside our door at night and gaze up at the sky, we first notice the brightest stars, but as our eyes adjust, we can see more of them. The typical person needs 12 to 40 minutes for their eyes to adapt and fully employ night vision. There are a few things you can do to decrease that time and maintain good vision throughout the night.

Preparing your eyes for night begins hours before the sun even touches the horizon. During the brightest part of the day, your eyes are overwhelmed with light. Start preparing early by wearing sunglasses and a sun hat all day. This will ease the transition into night and also protect your eyes from getting sunburned.

Exposure to light at night will interrupt your vision and require more time to readapt. Bright navigation instruments can be more than a nuisance for anyone serious about maintaining night vision. Be aware that frequent use of a chart plotter with a lit screen at night will impair your night vision, even on the dimmest setting. To best maintain night vision, first dim the lights on navigation instruments. Then turn off all the nonessential instruments. You can turn them on again in an urgent situation and they will already be programmed to a dim-light setting.

Your eyes adopt their night vision more quickly after exposure to red light instead of yellow or white. Use flashlights that have red bulbs in them. When you are using a spotlight to see shapes on the water, extend your arm outboard to prevent light shining on the boat or rig from reflecting back into your eyes.

Using Your Peripheral Vision Knowledge of ships’ light patterns is essential during night travel. Still, a lot remains unlit and hard to find and identify. Take this scenario as an example: Off the starboard quarter, you notice a dark form. But when you stop scanning and look back in its general direction, you can no longer see it. It’s as if it was there and disappeared, and your eyes are playing tricks on you. This is a common mistake resulting from being unfamiliar with scanning techniques that utilize the features of your eyes.

When light enters the eye it passes through the cornea to the retina. The retina has cone cells at the center, surrounded by rod cells. Rods function in low light because they are much more sensitive to light than cones. Because of the rods’ location, they are also used for peripheral vision. Therefore, oddly enough, your peripheral vision is better suited for finding forms on the horizon at night. Train yourself to mentally focus a few degrees on the periphery while still looking ahead. It seems odd not to look directly at what you want to see, but with practice this technique becomes second nature.

Scanning the Horizon at Night Without full understanding of the limitations of our eyes, scanning the horizon effectively can be impeded. Eyes have a difficult time focusing on objects when you’re in motion. Even though we often scan the horizon in a sweeping motion, it’s better to scan slower and stop at regular intervals along the way. Your eyes must move from point to point, stopping each time to focus.

Central vision is what we use to focus on reading, driving a car or seeing things directly in front of us. It only encompasses 3 to 15 degrees of the field of view, and is surrounded by the peripheral vision. For a thorough scan of the horizon, pause every 5 to 10 degrees so you don’t miss anything due to your narrow field of view.

One way to measure degrees is to use your body as a measuring tool. Raise your fist in front of you with an outstretched arm. The width of your fist is about 10 degrees. You can verify this by resting your vertical fist on the horizon and stacking one fist over another, hand over hand, counting each time. When you reach nine fists tall, theoretically it is 90 degrees, and you should be looking at a 90-degree angle from the horizon, or at your zenith.

Recognizing and Reducing Eye Fatigue Standing night watches is a tiring job, and fatigue will affect your ability to spot objects in the dark. Your eyes work best when looking straight ahead. While scanning, keep your eyes fixed ahead and rotate your head instead. This will reduce fatigue. It will also provide the clearest view. Even if you don’t notice it, your nose blocks some of your vision when you look to the sides by turning your eyes instead of your head.

Have you ever noticed colorful blobs that start to dance through your vision if you stare at one place long enough? This is a sign of tired eyes. Keep moving your eyes regularly through your scanning pattern. Your eyes are working much harder when they’re stationary for long periods. They also strain when they’re trying to see things that are far away. One way to rest your eyes as you systematically scan the horizon is to stop occasionally and focus on a close object in the boat.

When you’re standing watch at night, the things you’re looking for are small and hard to see. A dim blinking light, a dark spot in the sky or a gray form in the distance could inform you of shoals, approaching storms or even land. As prudent sailors, we do everything we can to ensure we are prepared for any situation. All too often, eye care, scanning techniques and maintaining night vision are subjects that get pushed to the bottom of our list and designated as low priority. However, because of the inherent challenges that nightfall brings, it becomes even more important to prepare properly. Understanding the abilities and limitations of your eyes at night, and developing techniques that will help maximize what you can see, could be the difference between avoiding a dangerous situation or sailing straight into it.

Quick Guide to Night Vision

• Wear sunglasses and sun hat during the day.
• Use red light bulbs in flashlights and cabin lights at night.
• Dim screens on navigation instruments and turn off unnecessary electronics.
• Allow up to 40 minutes for your eyes to adapt to night vision before setting sail in the dark.
• Practice making conscious use of your peripheral vision.
• Allow a moment for your eyes to focus by scanning slowly and stopping every 5 to 10 degrees along the way.
• While scanning, keep your eyes facing forward and rotate your head instead.
• Keep moving your eyes regularly through your scanning pattern.
• Stop scanning occasionally to rest your eyes by focusing on a close object in the boat.
• Practice using techniques for scanning and maintain night vision every time you go outside at night.

This article first appeared in the July 2014 issue of Cruising World. Teresa Carey and her husband, Ben Eriksen, offer sail-training expeditions aboard their Norseman 447. For more information or to read other articles by Teresa, visit her website .

instruments are set to dim or red lighting

• More: How To , safe boating , safety at sea , seamanship
• More How To

Surviving the Storm: A Sailor’s Tale of Hurricane Lee

Best Practices for Boat-Show Shopping

Grease the Wheels of Your Boat: A Guide to Proper Lubrication

A Bowsprit Reborn: A DIY Renovation Story

Savoring Superior: A Great Lakes Cruise To Remember

Point Your Compass Due South, Bitter End Yacht Club Reopens October 23rd.

Pre-Owned: 1988 Hylas 47

Understanding Wind in the West Indies

• Digital Edition
• Customer Service
• Privacy Policy
• Terms of Use
• Email Newsletters
• Cruising World
• Sailing World
• Salt Water Sportsman
• Sport Fishing
• Wakeboarding

Navigation Lights for Sailboats (And How To Read Them)

Navigation lights on a sailboat can be confusing. If you understand the reason behind why they are the way they are however, they can make a lot more sense.

At their heart, sailboats are really just a power boat and as such must adhere to all power boat rules such as navigation lights. Other times however, a sailboat is classified in a special category. They have a set of additional lights they CAN show as an option, but are not always required to do so.

That’s about as clear as mud if you ask me and I contend that that is where the confusion about lighting a sailboat begins.

Just because you can show a light to identify yourself in times of low visibility, does not mean you have to and then we add in a little sibling rivalry between power and sail and things get downright adversarial when it comes to navigation and the night.

Table of contents

The USCG says You’re a Power Boat Whether You Like It or Not

Much to the consternation of many a sailor who has earned a commercial license to drive their sailboat, when you received your credential from the USCG it says you are a master of steam and power across the top with no mention of wind as a source of propulsion.

It is not until you read the back pages of your little red book that feels like a passport and looks like a US Sailing credential, that you will see the term “sail auxiliary”. That is because most of the time the U.S. Coast Guard knows that you are primarily reliant on your mechanical power to propel your vessel.

It's a sad thing, but the days of commercially viable sail boats are done and all but the most select few even have sails let alone use them as their primary power source. All sail boats by law are powerboats, but not all powerboats are sailboats.

Navigation Lights for a Power Boat

As a power boat, you are required to show certain lights and have been required to do so before power was even invented. 

In the days of man powered vessels like the viking ships who relied on oars while in close quarters to power their vessels, they needed to show other boats, friend or foe, where they were by showing lanterns in the dark to identify themselves. As you know, it is a time honored rule among all the nations of the world both past and present, that you must avoid a collision at all costs while at sea and even the viking knew that you should not run into things.

By lighting the front and back of your boat, you could warn other boats of your presence as well as identify which way you were heading. As such there is a very specific rule in the Code of Federal Regulations Number 46 (CFR46 by common name) that spells out with detail how many, the color, the luminosity or brightness, the angle of visibility and the location of all of the lights required for navigation on every single boat, seaplane, submarine and other nondescript vessel conceived by man to date that they must show while underway in reduced visibility.

And there is no flexibility in the rules.

As such a power boat, and by extension all sailboats, MUST, without question show one green light on the starboard bow and one red light on the port bow and one all around white light or lights while operating in reduced visibility. These lights should shine at all 360 degrees of visibility with the bow lights shining at an angle of dead ahead to 22.5 degrees abaft the beam and the stern lights shining 225 degrees dead aft. A forward facing masthead light that is white in color shall shine forward to comply with the directive that all vessels must carry an all around white light. For more read here .

As you can see, there isn’t much wiggle room when it comes to lights that must be shown.

Sailboats get a little flexibility with lights

Sailboats however, are a little different when they are in fact sailboats, which is only when you are entirely reliant on the wind for power and in no way reliant on any mechanical or manual means of propulsion. And for good reason.

Back in the day when men were men and sailboats were wooden, fire was a major concern. Sails were coated with wax and other flammable substances and the wood on boats was saturated with oils and grease. Even the ropes were plant materials saturated with oils to keep them pliable and strong.

Add those highly flammable substances to a parching environment like the sea and you had what was essentially a giant floating tinderbox.

Then tell that giant floating tinderbox that they need to identify themselves to the world at large at night using oil lamps with flames because batteries and lights were not invented yet. It didn't take very long or very many ships burning to the water line for the Governments to say to the sailboats, you get to do things a little different.

As such, sailboats are given special dispensation when it comes to lights aloft. They don't have to show an all around white light in their rigging because no one wanted to set their rig on fire with oil lamps 60 feet up in their rig.

However, when a sailboat takes their sails down such as when they are powered or at anchor, they must resume the display of an all around white light or lights aloft. That became a real challenge with aluminum masts and the disappearance of rat lines on the shrouds because there was no easy way to climb the rig and check the bulbs up the mast on a regular basis. 

Red over Green Sailing Machine

I have no idea where the history of this particular light comes from, but if you ever take a deck exam with the USCG, you better remember this mnemonic. An all around red light over an all around green may be displayed on a vessel during times of reduced visibility to indicate that a vessel is operating under sail power alone. 

I won’t even speculate on how or why they came up with this particular light configuration, but if you want to use these lights as a sailing vessel, you can do so, but that means that you will need three all round lights at the top of your mast, an all around white, an all around red and an all around green, just in that order.

The red over green is to be displayed in addition to the running lights or the red and green bow lights with the 225 degree stern light. As always, when the motor comes on, so does the steaming light or the forward facing white light that is also usually about ¾ of the way up on your mast to complete the requirement of an all around white light that indicates a power vessel.

What is a “steaming light” and why are you mentioning it now?

Most sailboat electrical panels will have a switch that is labelled “steaming light” and it will only come on when your anchor light is off. This is probably the most confusing part of sailboat navigation lights so if you are confused about this, you're in good company as most people are. 

A “steaming” light is named thusly, going back to the days of steam powered sailboats where when they fired up their boilers and doused the sails, they became a power boat once again. There aren’t too many steam powered boats, let alone steam powered sailboats, but the name stuck and it is a vestige of a bygone era.

Either way, when you fire up your motor, you turn on your “steaming light” and that locks out the all around white light which is used for anchoring to minimize the number of switches on your panel and reduce the number of wires in your mast. The fewer wires, the less chance of something not working or becoming disconnected.

The steaming light and the anchor light both go up the mast, but you can’t use an all around white light while using the 225 degree stern light at the deck level because to other boaters you would look like you have two white lights from the stern and that would be confusing.

The anchor light is used exclusively for anchoring while the steaming light is used to indicate you are a power vessel while underway.

As to why I am mentioning it now in the article, is because this would have blown your mind if I started with this subject cause it can be really confusing stuff.

Aspect Recognition with Lights

Remember when I said earlier that lights can help you tell others which way you are heading as well as tell you which way other boats are heading? That is called the aspect of the vessel and the USCG tests you on this for your deck exam as well. 

Knowing that the bow lights go 22.5 degrees abaft the beam on both sides or 112.5 degrees on each side, and the stern light faces 225 degrees aft for a total of 360 degrees of visibility, you can tell a lot about where a boat is heading and who has the right of way.

One thing that's easy to remember is red means stop and if you see a vessel's red light, it means stop as you are the give way vessel and approaching the other vessel from his port side. Conversely it works with green as well as that means you are approaching from the other vessel's starboard side and you are the standon vessel.

If you see a red and green light equally low on the horizon, that means your heading dead on into another vessel's path and conversely if all you see is a white light low on the horizon, it means you are overtaking another vessel power or sail, we don’t care because it is an overtaking situation. However, any time you do see a white light aloft in addition to the red and green bow lights, you know you are encountering a power boat.

Then there are angular approaches as well, where you see white and red or white and green light low on the horizon. You know in that case you are seeing a portion of the bow lights and stern lights from the side approaches of a vessel. Based on which direction those lights are heading, you can deduce which way that boat is going in relation to your boat.

So put it all together and you see a green light and a white light low on the horizon with a red over green light aloft, you know that you are approaching a sailboat that is traveling to your port and that might make you the standon vessel. That is of course, if we didn’t concern ourselves with windward and leeward and port tacks and starboard tacks, but that is a discussion for another article. So stay tuned when we talk about sailing rules and the right of way. But for now, do good, have fun and sail far.

Related Articles

Capt Chris German

Capt Chris German is a life long sailor and licensed captain who has taught thousands to sail over the last 20 years. In 2007, he founded a US Sailing-based community sailing school in Bridgeport, CT for inner city youth and families. When Hurricane Sandy forced him to abandon those efforts, he moved to North Carolina where he set out to share this love for broadcasting and sailing with a growing web-based television audience through The Charted Life Television Network.

by this author

Most Recent

What Does "Sailing By The Lee" Mean?

Daniel Wade

October 3, 2023

The Best Sailing Schools And Programs: Reviews & Ratings

September 26, 2023

Important Legal Info

Lifeofsailing.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon. This site also participates in other affiliate programs and is compensated for referring traffic and business to these companies.

Similar Posts

How To Choose The Right Sailing Instructor

August 16, 2023

Cost To Sail Around The World

May 16, 2023

How To Drive A Pontoon Boat

Jacob Collier

December 19, 2022

Popular Posts

Best Liveaboard Catamaran Sailboats

December 28, 2023

Can a Novice Sail Around the World?

Elizabeth O'Malley

June 15, 2022

4 Best Electric Outboard Motors

How Long Did It Take The Vikings To Sail To England?

10 Best Sailboat Brands (And Why)

December 20, 2023

7 Best Places To Liveaboard A Sailboat

Get the best sailing content.

Top Rated Posts

© 2024 Life of Sailing Email: [email protected] Address: 11816 Inwood Rd #3024 Dallas, TX 75244 Disclaimer Privacy Policy

Astrolabe Sailing

Sailing, yachts, adventure and sailing around the world, colregs, lights & sailing at night.

Despite learning all my lights and being a nerd with the Coastguard Boating Education flash cards, when you are at sea at night it is really hard to decipher navigation lights on other boats.

I think the main difficulty I have is knowing how close you are to the other boat. We don’t have radar on board, so only have our eyes to judge. Is it a huge ship far away or is it a small ship really close? Who knows! Either way, I have no idea how close we got to the fishing boat we passed on the way back from the Sounds in January.

Here is everything I need to refresh for the Ocean Yachtmaster course I am currently doing:

I can highly recommend this online course if you are wanting to brush up on your knowledge: https://sistershiptraining.com

COLREGS – are the international collision regulations at sea and they are designed to ensure that boats know who gives way to who.

These rules apply to everyone on the water – boats and even sea planes!

One of the most important rules in the COLREGs is that all vessels shall maintain a proper lookout at all times. This means that you need to use not just your eyes but your ears as well – and if you have other means such as AIS and Radar – then great use those as well. If boats don’t obey this rule then all the other rules are pretty much useless. You wouldn’t drive your car along the street without looking right?!

Another important rule is that boats need to operate at a safe speed so that you can take proper action to avoid a collision – this means you have to take in to account the visibility, traffic density, your vessels manoeuvrability and distance required to stop, the state of the weather and sea conditions, and the depth of the water.

So if you are keeping a good lookout and notice another boat heading in your direction, you need to next determine if a risk of collision exists. A good way of doing this is lining up the other boat with a fixture on your own vessel – like a stanchion for example. If the boat stays in line with that (the bearing remains the same) then there is a risk of a collision.

So the next step is to figure out what the other vessel is up to and then make a decision on who is going to give way to whom.

There are a few different ways of doing this – some will be obvious, and others require a bit more consideration. But you will need to take some action and it should be made in ample time and with consideration of good seamanship.

The give way boat can take action by slowing down, stopping or changing course and doing so in a manner that the other boat can see that you have done this and they can stand on.

So how do you identify what the other boat is up to and decide if you are going to give way or not? Lets start with some easy ones:

In Narrow Channels

Boats should keep to the right hand side of the channel – and pass port side to port side.

If you are a small vessel – yacht or powerboat, you should give away to all vessels who can only navigate in this channel.

So here in Lyttelton for example – we can sail all over the place, but the ships can only navigate down one strip of the harbour which is dredged. We must give way to them because they are “constrained by their draft”.

If you get in their way – they will give you five short blasts on their horn which basically means “Get out of my way!!!!”. ( Trust me this is not fun …)

People who are under way tend to give way to boats which are anchored.  (see this is all common sense people!!)

If you are at anchor – you must show an all round white light. Or during the day – a black ball suspended at the bow. If the vessel is over 50m, then they show two all round white lights – one at the front and one at the stern. If the vessel is over 100m in length then they must also show other lights to illuminate the decks.

Boats less than 7m and not going faster than 7 kts

If you are a fast manoeuvrable boat, and not restricted in the way  – then you should give way to smaller boats

At night they also only need to show an all round white light, or if you are in a dinghy you can use a torch. Basically just try not to run these slow little guys over, and likewise, if you are small and slow you might not want to be navigating through busy shipping lanes at night if people are unlikely to be able to see you.  (just sayin’!!)

Boats Navigating at Night – Port, Starboard & Stern Lights

These are shown when a vessel is under way (i.e. not at anchor) and help you to identify which direction a vessel is travelling. If you can see both the red and green at the same time, then it means they are heading straight for you!

If you can only see a white light then it could either be a vessel at anchor, a slow vessel travelling at less than 7kts or a vessel travelling away from you – its stern light.

Yachts or if you are from America – Sailing Boats

Yachts under 20m, when sailing must show a port, starboard and stern light and they can be combined in a tri-coloured mast head light.

If the yacht is motoring then it also needs to show a seperate stern light and a masthead white light.

If the motor is on – then you are considered to be a power driven vessel and those rules apply – see below.

Yachts  – when they are sailing, have right of way over power boats – including ships when you are out at sea. When yachts are on starboard tack, they have right of way over yachts on port tack. And leeward boats have right of way over the windward boat when they are both on the same tack. (I won’t go in to heaps of detail on this but its worth doing some more research on this if you are planning on sailing in the vicinity of any other yachts)

Power Boats

Powerboats over 12 metres in length must show the port and starboard lights, a stern light and a mast head light – which should be 1 metre higher than the sidelights.

If the powerboat is less than 12 metres then it can combine its stern and masthead light in to one all round white light.

Power boats give way to other boats approaching on their right hand side.

Note that in the picture above, say the white boat doesn’t look like it is going to give way and the stand on vessel decides to take action themselves – they should turn to starboard – if they went to port and the other guy decided to finally show that he was giving way then you could cause another crash.

Towing Light

If you are towing another vessel, you display a yellow light instead of a stern light. This means that you have right of way over most boats. When you are towing you a restricted in your ability to manoeuvre, but you still give way to anyone who is anchored, aground, and constrained by their draft.

Under Way & Making Way

Under way, means that a vessel is not anchored, docked or secured. Making way means that it is actually moving through the water/over the ground.

Vessels Not Under Command

These are vessels which are unable to manoeuvre and keep out of the way of anyone else. Perhaps they have lost all power to their engines or broken their rudder or something like that.

They show two in line all round red lights or two red balls during the day. If they are actually making way through the water then they must show port, starboard and stern lights too.

I remember this by thinking of two red stop lights – i.e “Stop stop these guys are not under command”

Now this is where it gets a bit more complicated…!

Vessels Over 50m in length

Must show two white mast head lights (facing forward) and one white stern light. The front light should be lower than the main masthead light. They also show port & starboard lights.

Vessels Aground

Obviously if a vessel is aground then it isn’t going to be able to give way to anyone else! These guys show two all round red lights over one white.

Vessels Restricted in their Ability to Manoeuvre

These vessels are restricted in their ability to move because of the nature of the work they are undertaking – so they might be dredging, towing, launching aircraft or something like that.

They show three lights all in line red, white red or a ball, diamond, ball during the day.

If they are fishing or dredging, and this might be a hazard to other ships, then they will display two green lights or two diamonds on the safe side, and two red lights or two red balls on the side with the obstruction.

Basically everyone except vessels not under command or aground, must give way.

Not sure how I remember this one but I seem to be able to!

Vessels Constrained by their Draught

These are big ships who are restricted to the channel, and can not deviate or they will run aground. They give way to vessels not under command and vessels restricted in their ability to maneuver, but everyone else gives way to them.

They show three all round red lights in a line or a cylinder during the day.

Pilot Vessel

Shows a white over red light.

I remember this one with the rhyme “White over red, the pilot is out of bed”

Vessel Fishing

A vessel fishing usually shows a red over white light or two triangles facing point to point (wine glass shape)

I remember this one with the rhyme “Red over white, fishing at night”

However they can also show a green over white light if they are trawling. If they have a single triangle out to one side, or a single all round white light, then this indicates that there is fishing gear extending out that side for 150m.

Vessels Towing

If the length of tow is less than 200m the towing vessel shows two all round white lights or a diamond shape and a yellow stern light. The vessel being towed shows their normal lights.

If the length of tow exceeds 200m, then they display three all round white lights.

Other Rules of the Road

In Harbours

Smaller boats should give way to any ships over 50m in length.

In Narrow Channels or meeting head on.

Vessels should stick to the starboard side of the channel, alter course to starboard and pass port to port.

When Overtaking

The overtaking vessel gives way to the stand on vessel being overtaken. The stand on vessel can pass either side, but should make their intentions clear. The stand on vessel should maintain their course, and avoid speeding up to race the passing vessel or swerving over in front of them to stop them from being able to overtake… 😉

You know you are the overtaking vessel if you can see the other vessel’s stern light. If you can’t see that then you are a crossing vessel and the ‘give way to your right’ rule applies.

If you are overtaking and want to let the other vessel know what you are doing – you sound two long blasts followed by two short blasts. This means I am going to overtake you on your port side.

The stand-on boat being overtaken and sound a reply with one long one short one long and one short and moves over to the right.

Sailing Vessels

Power boats should give way to yachts.

We have got heaps of crazy yacht rules, but basically those on port tack, give way to those on starboard, and windward boat gives way to the leward boat. Alternatively in a race whoever yells the loudest and has the biggest balls usually gets their own way.

Power Vessels Crossing

You must give way to a vessel on your starboard/right hand side. If the vessel to your left does not appear to be giving way to you, then you should turn to starboard, because if you turn to port (or towards them) and they finally figure out what they are doing and try to pass astern, then you could crash.

Honestly, you would not believe the number of people who have boats and have absolutely NO IDEA what any of these rules are. Arraggh!

Confused? Here is a bit of a summary. Anything listed above your kind of vessel you give way to – anything below gives way to you.

• Vessels Not Under Command. (So thats someone who has lost their engine or steering and can’t control where they are going. You’ll also want to give way to all vessels who are at anchor and aground…)
• Vessels Restricted in their Ability to Manoeuvre RAM (Towing someone, big ships in narrow channels, laying submarine cables, etc)
• Vessels Constrained by their Draft (big boats restricted to the shipping channel)
• Vessels engaged in fishing (no that does not include you if you’ve got your rod over the side – but big fishing boats with gear extended)
• Sailing Vessels – while actually sailing – give way to boats on starboard tack and boats on the same tack to leeward.
• Power Driven Vessels – anything motoring along gives way to anything approaching on their right hand side

Share this:

Related posts.

Seasickness

Sailing Qualifications

Heavy Weather Tactics

Marine Medic

Flags & Signalling

Yachting NZ Medical Stores List

The Catlins Coast – New Zealand

15 thoughts on “ COLREGS, Lights & Sailing at Night ”

The day signal to show you are on anchor is one we found not many knew – they’d ask us if we kept our lunch in the ball! 🙂

Like Liked by 1 person

Would be a handy place to keep it! Is it actually a ball or a flat circular shape? Did you hoist it up the genoa halyard or where?

Great post! Lot of lighting stuff i didn’t know!! Very informative. Thank you 🙂

I also heard stories of people calling “Starbard” and the response is “14 tonne!!!” (Or more) …… 😉

Very cool post, thank you for sharing. It is fun comparing these regs to the regs here in the US. For the most part they are the same however here each State has slightly different rules regarding small boats.

Good to know!

Pingback: Ocean Yachtmaster | Astrolabe Sailing

Pingback: Sailing at Night | Astrolabe Sailing

Pingback: Coastal Skipper | Astrolabe Sailing

Constrained by draught over RAM.

Pingback: RYA Offshore Yachtmaster | Astrolabe Sailing

My understanding of colregs was that no vessel ever has “right of way” vessels are either “stand on” or give way. The stand on vessel does not have a right of way but an obligation to hold course and speed to enable the give way vessel to manoeuvre that craft to avoid collision.

Further should the stand on vessel become concerned about collision they are obliged to take avoiding clear manoeuvres at an appropriate time or not a last second manoeuvring risk laden turn off speed change.

Long story short “I had right of way” won’t wash in maritime court.

Yes good point. Everyone has a responsibility to avoid a collision 🙂

Leave a comment Cancel reply

This site uses Akismet to reduce spam. Learn how your comment data is processed .

• Already have a WordPress.com account? Log in now.
• Subscribe Subscribed
• Copy shortlink
• Report this content
• View post in Reader
• Manage subscriptions
• Collapse this bar

Boating at night - Navigation lights to display in Canada Requirements in Canada

• Boating Safety Equipment
• Types of navigation lights
• Boat Navigation Lights rules and requirements at night

Powerboats navigation lights at night

• Powerboats less than 12 meters (39,4") in length
• Powerboats of 12 meters (39,4") and over in length
• Powerboats at anchor

Properly lit sailboat at night

• Sailboats under 7 m (23’)
• Sailboats from 7 m (23’) to under 20 m (65’7”)
• Sailboats 20 m (65’7”) and over
• Sailboats operating under motor power
• Sailboats at anchor

Commercial boats navigation lights at night

• Navigation lights for a vessel engaged in fishing  

Navigation lights for a vessel engaged in trawling

Navigation lights for a power-driven vessel when towing.

• Navigation lights for a government vessel

Navigation lights for powerboats less than 12 meters (39,4") in length

A power driven vessel of less than 12 meters in length, and underway, may display, from sunset to sunrise:

All-round light (white) forward and,

Sidelights (red – green).

Navigation lights for powerboats of 12 meters (39,4") and over in length

A power driven vessel of 12 meters and over in length, and underway, may display, from sunset to sunrise:

Masthead light (white) forward,

Sternlight (white) and,

Navigation lights for powerboats at anchor

At anchor,  the operator of a pleasure craft shall display, from sunset to sunrise, in the fore part,  an all-round light .  A powerboat anchored at night must display  an all-round light .

What is a properly lit sailboat at night?

Navigation lights for sailboats under 7 m (23’).

and underway, may display, from sunset to sunrise:

Sidelights (red – green) and,

Sternlight (white).

• 1 lantern, combining the sidelights and stern light above.

Navigation lights for sailboats from 7 m (23’) to under 20 m (65’7”)

• Sternlight , and
• 1 lantern, combining the sidelights and stern light above

Optional - A sailing vessel may exhibit at or near the top of the mast, two all-round lights in a vertical line: the upper one red and the lower one green. These lights are shown along with the sidelights and sternlight.

Navigation lights for sailboats 20 m (65’7”) and over

Navigation lights for sailboats operating under motor power

Sailboats are considered powerboats when they have the engines on - even if the sails are up. 

Masthead light  (white) forward,

Sternlight  (white).

Navigation lights for sailboats at anchor

Navigation lights for kayak or canoe (human-powered vessels) at night

Navigation lights are also required for  human-powered vessels (canoe, kayak)  or for a sailing pleasure craft of less than 7 meters in length not under power. When underway,  the operator  shall, from sunset to sunrise, display, if practical, sidelights and a stern light, but if the operator cannot, he/she must have at hand , a   flashlight   or lighted lantern emitting a white light which must be lit in enough time to prevent a collision.

Navigation lights for a vessel engaged in fishing 

Sidelights ,

Sternlight and

All-around light in a vertical line, the upper being red over white light. When making way through the water.

A  vessel when engaged in trawling , which means dragging a dredge net or other fishing apparatus through the water, shall display:

Two all-round lights in a vertical line, the upper being green and the lower white. When making way through the water,

Sidelights and 

Sternlight.

Navigation lights for a government vessel (Police boat)

Any government vessel or any vessel that is owned or operated by a harbor, river, county or municipal police force may display a blue flashing light to identify itself as such, in the following cases

When it is providing assistance in any waters to any vessel or other craft;

When it is engaged in law enforcement duties in Canadian waters.

Power-driven vessel when towing shall show sidelights, a sternlight, and a towing light in a vertical line above the sternlight, and two masthead lights in a vertical line. When the length of the tow, measuring from the stern of the towing vessel to the after end of the tow exceeds 200 meters, three such lights in a vertical line shall be displayed.

Apart from the regular navigation lights, when a boat tows another vessel in distress or in need of assistance for any reason, shall take all possible measures to show the relation between the towed vessel and the vessel doing the towing. A vessel towing must try to shine a light on the towing cable to make it as visible as possible, so that other boats do not come into contact with the cable.

A vessel being tow shall display sidelights and a sternlight. If it is not possible, it must display one all-around white light at each of the fore and aft ends.  

Navigation lights for a power-driven vessel pushing another

A power-driven vessel, when pushing another , shall display the sidelights, a sternlight, and two superimposed masthead lights. 

The vessel being pushed, and not part of a composite unit, must display its sidelights at the bow. When a vessel is pushing another, if both are connected in a rigid, composite unit, they will be regarded as one unit, thus showing the appropriate lights.

Navigation lights Examples

Sailing vessel seen from starboard side.

Sailing vessel seen from the front

Power-driven vessel anchored

Power-driven vessel seen from starboard side

Power-driven vessel seen from port side

Power-driven vessel seen from the stern (back)

Would you like to learn more about boating safety and be able to drive a boat?

Aceboater s'  boating safety course  is accredited by Transport Canada to train students on the rules of navigation, buoys and their meanings, boating navigation lights, hazards, how to respond to emergency situations, boating laws and more.

Our course, once successfully completed, will give you the official  pleasure craft operator card  from Transport Canada, valid throughout North America.

I want my official  Canadian boating license .

• Follow Ace Boater on YouTube
• Join Ace Boater on Facebook
• Contact Ace Boater
• AceBoater on Instagram
• AceBoater on X

Boating License & Pleasure Craft Operator Card online exam - Accredited Transport Canada

• Refund Policy
• Privacy Policy

Yachting Monthly

• Digital edition

Night sailing tips for first timers

• Toby Heppell
• September 4, 2020

Cruising after dark doesn't need to be stressful. Toby Heppell shares his tops tips for night sailing

Sailing at night can be a magical experience. Credit: Paul Wyeth

Do you find night sailing stressful? It needn’t be if you follow a few basic rules and plan ahead.

Stay on deck while night sailing

As always with pilotage, the right place to be is on deck, not least to avoid uncharted objects such as other craft, mooring buoys and fishing pot markers.

Most pilotage errors occur at night rather than in the day so a thorough pilotage plan is essential.

Even with a navigation station filled with electronic aids it is still possible to become disorientated while trying to reconcile the view on deck with that on the chart.

Where possible, the right place to be is on deck. Credit: Paul Wyeth

You need a pilotage plan.

The most important principle is this: if you know the position of the yacht and you are armed with a chart (electronic or paper) and a compass, you know the range and bearing to the next mark.

This means that when you reach a known position, such as a navigation buoy, you know where to head to find the next one.

Simple, except that a surprising number of navigators waste time scanning the lights ahead with no plan to find the one they want.

Fishing pots

Unpredictable and unlit, these are the biggest danger at night.

Avoiding them is largely a matter of common sense.

Sometimes they are laid in deep water, but mostly they lurk in less than 50m.

Fishing pots, hard enough to spot in the daylight, become all but invisible at night

Avoid shallows if you can, especially near fishing harbours, and inside passages around headlands, even if you are confident of your position thanks to radar and plotter.

Even if you know where you are, there’s still the same risk of the engine stopping with a crunch, or finding yourself moored by the rudder or prop in a strong tide.

Light pollution

Light pollution is a well-known source of navigation stress, particularly when looking to enter an unfamiliar harbour after dark.

If it has been a while since you have done this, it is well worth returning to your own harbour after dark and noting the different complexion the various landmarks take on when not visible to the naked eye.

A large, unlit buoy may be sited just in front of a particularly well-lit hotel rendering it difficult to spot.

Another feature of light pollution (but of sailing at night more generally too) is the reduction in our ability to judge distances.

This is particularly acute when coming into harbour.

A navigation buoy’s light may well get lost in the background of a sea of lights when, during the day it would be clear and obvious the nav buoy was some way offshore.

Night vision

The sensitivity of our eyes increases the longer they are in the dark and it can take many minutes for maximum sensitivity to be acquired, and the improvement is dramatic.

Unfortunately it can be lost in a few seconds of exposure to bright lights.

Eyes have cones that are used for colour vision in daylight, and more sensitive rods that come into their own at night.

The rods are not sensitive to red light and this means that if you switch to red illumination your eyes can continue to adapt while you move around the boat.

The bad news for those of pensionable age is that your eyes will only be about a third as sensitive to low light as in your youth.

Is red light at night always best?

Binoculars will boost illumination by about 50 times and go a long way to redressing the balance.

However, it still pays to have your youngest crew on lookout.

It is worth noting too, that in this high-tech age, our cockpits are often filled with screens all giving off light.

Most of these screens can be dimmed or put into night mode, but sailing in the dark can be such a calm experience that the harsh light of screens can detract.

Keep your electronics on and functioning and use as appropriate.

If they are on and lit up in the cockpit they tend to draw the eye and can have the effect of making you less aware of that which is going on around you.

Poorly lit craft

Inshore, yachts can be hard to spot.

Coming into places like Southampton, Portsmouth or any other significant port with strong background lighting and a tight channel for leisure craft you are likely to be up against a significant confusion of lights.

Yachts are especially awkward if they opt for a tricolour at the masthead instead of proper running lights in close quarters.

You are looking ahead for trouble, not up in the sky!

Tricolours are great on passage though, increasing the likelihood of being spotted and minimising power drain – remember, do not use your tricolour when under power.

Fishing boats’ navigation lights are often made hard to see thanks to a bright deck light to enable the crew to work on deck.

Many larger ships are well lit up at night making them easier to spot. Credit: Colin Work

Watch them closely and expect erratic course changes.

Try to give them plenty of space to stay safe.

Around the UK other than the decklights making it hard to discern their heading from a distance, fishing craft should not cause too much worry.

But, you will want to avoid ending up astern of them in case they are trawling, so do take plenty of time to discern their direction of travel.

In some parts of the world fishing craft of various sizes do sometimes operate without proper lighting, so if you are entering a busy seaport always take it slowly.

Cruise ships and ferries are invariably lit up like Christmas trees.

It can be hard to pick out the red and green amongst the plethora of other lights onboard, so take time to work out what they’re up to and consult AIS if you have it.

Given their size, if you are close to shore even without seeing their nav lights it is usually fairly easy to make a decent guess at their bearing relative to you by glancing at your chart to get a sense of the main nav channels.

Safety on deck while night sailing

For the most part you will have your own rules about when lifejackets go on, whether that be worn the whole time, when the windstrength is above ‘x’ knots etc.

The strong recommendation is to always wear a lifejacket when on deck after nightfall, and this is sensible.

Some choose not to in calm weather and if they are in the cockpit.

As ever, what you decide will be between you and your crew.

Wearing a lifejacket when sailing after dark is advisable

For my part I would strongly recommend a lifejacket at all times after dark.

Clipping on via your harness is also strongly recommended.

If you are sailing a long passage at night then do be aware of your harness clip scraping along the deck if you are moving around – it’s a very irritating noise for those trying to get some kip below.

It’s not always easy to force discipline on yourself, but it really does make sense to call on your crew if you need to go up on deck for any sort of sail adjustment.

Safety is not about buying things.

It is about an attitude of mind.

We must constantly be on the lookout for trouble at night so that we can forestall it, just as we do in the daytime.

If you are setting out on a passage that may well extend into the night, it is worth considering what food you intend to take.

There is a lot to be said for preparing an evening meal before set off.

Something like a pre-made stew can be easily heated and give you a boost to cover the last miles.

It can also help you warm up on deck or make for a hearty meal once you are tied up.

Have snacks and hot drinks easily to hand

Whatever you choose, make plenty of it, that way you have enough to get you through the night, or you can have a bit to keep you going but still have a meal left when you arrive at your destination.

Hot drinks are axiomatic.

Boiling a kettle and having somewhere safe to place a mug while you make an instant coffee has to be easy.

If it isn’t and you are reduced to pre-heating thermos flasks, there is something wrong with your boat or your arrangements.

Keep the drinks coming.

They maintain morale and give people something to do.

Effect on weather

All air usually cools at night, even over the sea.

This will be more obvious when it has been a sunny day not far from land.

The result is that there are fewer gusts and a decrease in the average wind strength as the thermally enhanced breeze disappears.

On a night with low-lying cloud or hill fog, some lighthouses will not be visible.

Note the height of the lantern from the chart and be ready for the occasional disappointment.

Continues below…

Is red light at night best?

Dag Pike considers the age-old adage that using red light preserves your night vision

How to tackle a night passage short-handed

Worried about ‘things that go bump in the night’? Tom Cunliffe says night sailing is easier than you think –…

Night pilotage: How to enter unfamiliar harbours

James Stevens looks at how best to prepare for arriving at an unfamiliar harbour after dark and what to be…

Halos around the moon can be really obvious at night.

A big one is often a sign of an approaching front.

If the wind is light, think about starting the engine and keeping up boat speed.

In conditions when the air is moist, a degree or so of cooling after dark might be just enough to shut down poor-to- moderate visibility into mist or even fog.

Distant lightning is more easily seen at night, so don’t be too alarmed if you see it flashing around the horizon.

Sailing and sail handling while night sailing

Once darkness falls, moving around on deck should be reduced and so it makes sense to have out sails that are well within the conditions at the time.

Many skippers like to shorten sail before dark, regardless of conditions, so as to minimise the chance of having to handle sails at night.

However, you should still be willing and able to change sails, or take in or let out reefs, if necessary, particularly if you are on a long passage.

It is a very good idea to mark your halyards so that you can roughly get them in the right place for reefs etc.

Some skippers like to shorten sails as night falls to minimise the chance of sail handling. Credit: Graham Snook/YM

You should also have a working set of deck lights, so you can illuminate everything when doing big jobs.

If you are not far from your final destination and daylight is disappearing, it might be worth switching the engine on and getting sails down and tidy before the dark really takes hold.

But if you’re confident in your passage plan then this is far, far from crucial.

Reducing sail, however, helps with your own ability to see and be seen.

In busy areas many sailors like to have quite a bit of the headsail rolled away as this improves visibility looking forward – a good idea for busy ports in daylight too.

At the beginning of the night, the skipper should make sure everyone understands what adjustments can be made unsupervised by those on deck and when more crew should be called up to assist.

This may vary, depending on the crew’s experience.

Intuitive sailing

There are additional strips you can get added to sails that glow at night to allow you to properly set them at night, but this is really only necessary for racers and those looking to make very long night passages.

In truth, there is usually enough light to get some decent sense of how your sails are set, and if you have reduced sail before night falls, then the consequences of getting things wrong is just a slowing of pace.

Having a torch handy to check trim and telltales is a real help.

Toby Heppell got his first boat aged four and grew up sailing on the East Coast. He has been a sailing journalist for over 15 years. Credit: Richard Langdon

Though some are tempted to switch on the motor once dark falls, sailing in the dark is a really fun and tranquil experience and can improve your sailing skills during the day.

Without the ability to see gusts approaching on the water, your sail trim is going to be far more reactive than it might otherwise be.

Feel becomes key when sailing at night.

Sailing by feel is something of a specialism for blind sailors.

Lucy Hodges, Blind Sailing World Champion, once offered me this advice: ‘A key area for me when sailing are the hairs on the back of my neck. I always make sure that my neck is exposed. With a bit of practice you may be surprised how quickly you can lean to feel changes in wind pressure and direction.’

The key to sailing by feel, is using all of your senses.

Feeling the roll of a boat is essential, if you feel the boat is starting to heel, and if the hairs on your neck have not changed, the wind might not have altered and you probably want to adjust course slightly.

If the boat begins to heel and the hairs on your neck feel different, the wind may have increased so you might adjust trim.

Of course with visual inputs too, we do not need to sail entirely on feel when night falls, but it does stand as a great example of how different and rewarding sailing at night can be.

It can really help you feel more in tune with your boat.

For all the latest from the sailing world, follow our social media channels Facebook, Twitter and Instagram .

Have you thought about taking out a subscription to Yachting Monthly magazine?

Subscriptions are available in both print and digital editions through our official online shop Magazines Direct and all postage and delivery costs are included.

• Yachting Monthly is packed with all the information you need to help you get the most from your time on the water.
• Take your seamanship to the next level with tips, advice and skills from our expert skippers and sailors
• Impartial in-depth reviews of the latest yachts and equipment will ensure you buy the best whatever your budget
• If you are looking to cruise away with friends Yachting Monthly will give you plenty of ideas of where to sail and anchor

• Forum Listing
• Marketplace
• Advanced Search
• All Topics Sailing
• General Sailing Discussions
• SailNet is a forum community dedicated to Sailing enthusiasts. Come join the discussion about sailing, modifications, classifieds, troubleshooting, repairs, reviews, maintenance, and more!

Lighting while sailing at night.

• Add to quote

I had an interesting experience while racing recently that posed an interesting question. I was sailing (on a port tack) towards the turning mark of a long distance course in the dark. We were lit like a sailboat should be, running lights and sternlight as well as a masthead red over green sailing light. Closing us on a steady bearing (risk of collision) was a vessel showing sidelights and a white light higher than the side lights. My watch Captain judged that this was a vessel under power and that we (under sail) would have the right of way. When it was apparent that the other vessel wasn't going to give way we crash tacked and got out of its way. As it went by, we saw a sailing vessel (on a starboard tack) with its anchor light on. When I later asked the skipper (he was in the same race) what he was doing, he said that they often sailed with the anchor light on so they could see the masthead wind indicator to ensure they were trimmed right. He claimed he had the right of way (starboard tack vice port tack) He never considered that it would confuse other vessels because his anchor light was on. It was a close call. Thoughts? How do you folks see wind direction and set trim at night? Gaz  

He was wrong. My tricolor provides the same convenient illumination of the masthead fly while remaining legal, although there is some risk inshore that people won't look high enough to see the tricolor. Tell him to get a wind instrument (or another if he already has one) and mount it where the trimmers can see it. That said, I'm not sure what good that will do. We get more value from someone on the windward rail (or cabintop in light air) playing a flashlight over the telltales.  

Boaters in our area constantly do this and it drives me crazy. They will sail with thier steamming light on or with the anchor light on or with both on. They think that it makes them more visable (Or so that they can see thier masthead) but all it realy does is add to the confusion. We don't race, but the results are the same.  

Plumper said: How do you folks see wind direction and set trim at night? Click to expand...

He's an idiot. By sailing with the anchor light lit, he's effectively saying that he is under power and given up his rights as a sailboat. A sailboat, under 12 meters IIRC can use an all-around white light in addition to a bicolor to indicate that it is under power, rather than using a bicolor, stern and steaming light. If you have proper wind instruments aboard, you shouldn't need to light up the windex, since the wind instrument display head, at deck level, usually in the cockpit will give you the same information. If he's too cheap to invest in one...he's gonna get hit one of these days.  

The little Windex lights work great. You can buy the Windex brand name which mounts with your Windex. The only disadvantage is the extra pair of wires to run up the mast. They just light up the Windex and are not very noticible otherwise. Running with your steaming or anchor light on is of course wrong and if I had someone in our race fleet who did it I was politely mention it once then protest if he/she continued. I should add that occasionaly I have seen the steaming light put on to help wort out a problem on the fore deck but the helnsman should be aware that night vision will be affected and they have no rights. Gary  

I'd think you should have protested to the race committee - and had him thrown out as a unsafe participant. Not everyone can afford or wants a Tridata ST60+ or equivent with repeaters in the cockpit, that doesn't give them permission to conflict with the law, and be unsafe. OTOH - a flashlight shined at him before it became a crash tack would have shown he was a sailboat - you too have a responsibility to be safe. Assuming the other boat sees you, knows the rules and will obey them has probably dented more sailboats than anything else on the water.  

Plumper said: I had an interesting experience while racing recently that posed an interesting question. snip Thoughts? How do you folks see wind direction and set trim at night? Gaz Click to expand...

Shining a flashlight on another boat in the dark is not on. That would completely blind the guy that is about to run into you. Not a great move. Perhaps shining a flashlight on your own sails is more appropriate. Does it matter whether the white light at the top of the mast is a dim windex light or an anchor light? If it is at all visible from another boat it would confuse things wouldn't it? When scanning with binoculars those "low wattage" lights might not seem so low. I suggest that if there are any other boats in the vicinity then using any light at all to illuminate your windex is wrong.  

Plumper said: Does it matter whether the white light at the top of the mast is a dim windex light or an anchor light? If it is at all visible from another boat it would confuse things wouldn't it? When scanning with binoculars those "low wattage" lights might not seem so low. Click to expand...

I suggest that if there are any other boats in the vicinity then using any light at all to illuminate your windex is wrong. Click to expand...

I think that any light you are going to be able to see from 50 feet straight down is going to be visible from elsewhere.  

You don't have to see the light from the cockpit, you only need to see the windex. The windex light points straight UP at the windex, so that the light reflects off of the windex. The underside of the windex is tagged with reflective materials, so the light doesn't have to be very bright. Like I said, I believe it should be possible to design a windex light that illuminates the windex without being visible from off the boat.  

You could paint the forward 180 degrees of the windex light and it would be fine...for seeing the windex. You could have it on a switch and douse it when approaching another boat. You have to understand it's like a 2 watt light. The trilight or the running lights on the hull would be far brighter than this, and as it is commonly *behind* the trilight, and *below* its housing, you would only see it from the stern, meaning you'd see a very dim yellowy light, with a freaking bright white stern sector of a trilight above it. I've used these. They are dimmer than penlights used in cockpits. If a binnacle light at the helm doesn't cause a collision, neither will this.  

Plumper- If the light fixture is properly designed, with the light pointed up, it will not really be visible from any boat, unless your boat is knocked down. The way a Windex light works, it shines the light on the Windex arrow and the guides, so that you can see how it is oriented. It doesn't require any light be cast in a downward direction at all. Valiente- Anchor lights can be used as a combination steaming and stern light on boats less than 12 meters that are under power.  

BTW, generally, shining a light at another boat is a bad idea at night. If you blind their helmsman, it can take up to an hour for them to recover any signifcant night vision. Shining it on your sails is a much better idea. The only possible exception to this is the bridge of a large ship...where you'll likely not blind them, but will bring your boat to their attention. The bridge on most large ships is far enough away that your light won't blind them, at least at any position where you'll be able to shine it at the bridge.  

sailingdog said: BTW, generally, shining a light at another boat is a bad idea at night. If you blind their helmsman, it can take up to an hour for them to recover any signifcant night vision. Shining it on your sails is a much better idea. The only possible exception to this is the bridge of a large ship...where you'll likely not blind them, but will bring your boat to their attention. The bridge on most large ships is far enough away that your light won't blind them, at least at any position where you'll be able to shine it at the bridge. Click to expand...

As a person with many hours watchkeeping on large ships (thousands) I think shining the light on your sails is better. Not because the light will blind the BWK but because the sails will glow and the light is just a pinpoint.  

I use a flashlight when I want to see the windex. Easy, cheap and there when you need it. As for ruining the night vision of crew on a boat that's about to run you down....I wouldn't worry about it. Quickly sweep the light across their bridge -- the "flash" won't effect night vision that much, but it may get their attention, which is what you're trying to do in the first place. A strong light on the sails should be the first thing -- followed by the more agressive tactic above.  

Billyruffin, "the "flash" won't effect night vision that much" Wrong answer - it will effect night vision. Does the flash of a camera effect vision? Do it and you'll be liable if the blind helmsman runs you or anyone else down. Redlight your sails if you want to get attention. Night blinding a helmsman might get you more attention than you want.  

I've got two problems I think I can solve with one light, but is it legal? When putting together my boat, I installed this light on the masthead http://www.boatersworld.com/product/197260193.htm?bct=t13098025%3Bcielectrical-boat%3Bcilighting%3Bcinavigation-lights It is a two bulb fixture and I currently have it wired as an anchor light with both bulbs coming on at the same time. The problem is that I can't see my windex at night and my stern light attracts hoards of insects, plus it does impair my night vision a bit. If I wire it so that just the rear facing portion comes on when sailing and kill the stern light, am I still legal? How much risk do you think I'll have with no deck level stern light?  

I use the windex when cruising as a short cut. When racing with a crew, who cares? If you are beating you know how far you can bring the jib in - bring it all the way in and sail the telltales. At night, that means someone on the rail uses a flashlight so the helm can see the telltales. If you are reaching, the helm sets the course and someone on the rail lights up the telltales so the trimmers can see (or calls guidance back to the trimmers). The windex is a big picture tool, not a tactical trimming tool. You don't need it lit up all the time.  

You probably should be cranking on the wheel long before this (right after you sound five short blasts and flash your light five times).  

Billyruffn - you make an excellent point! I always get annoyed when a pedestrian walks in front of a moving car when the motorist doesn't see them, almost gets run over and then yells "I have the right of way!" I always told my kids, "You may have the right of way, but if you're dead it really won't matter. Never argue with a ton of metal, you'll lose..." In our case, never argue with 20 tons of Bayliner bearing down on you...  

Your lights were incorrect also If I recall correctly, rules of the road specifically prohibits using running lights and tricolor mast head lights at the same time. I read through the first page of responses and was surprised that no one had pointed this out. Ardie in Virginia  

We normally sail with an LED tricolor (to save A-Hrs). On a 3400 nm passage to the Marquesas we saw only one freighter, first by her lights then on radar. Hailing them on VHF, they couldn't see our 44' fiberglass boat (with a good radar reflector) at 2-3 nm until we briefly turned on our strobe . A Windex illuminator might cause confusion in close quarters, but we worry a log more about being seen at all -- we always assume we are invisible.  

The purpose of a boat showing lights while under way at night is to identify to other boats the type of boat, its' form of propulsion, and course it is following. By showing a different set of lights the sailor trying to light his windex is in violation of various rules of the road and would be found liable in any collision. He surely should have been disqualified from the race, the same as if he had been using a sail that was not allowed by the rules. I have used the small windex light at the masthead for illuminating the windex for many years and it is very effective and virtually invisible to other boats.  

• ?            
• 176.4K members

Top Contributors this Month

Boat Reviews

• Boats Specs
• Marine Pros
• Boat Insurance
• Boat Warranties
• Boat Transport
• Boat Towing
• Marine Forecasts

Your Ultimate Boating Resource

What do sailboats do at night?

Sailboats are a beautiful sight in the water during daylight, but have you ever wondered what these vessels do at night? Sailboats behave a little differently in the dark due to the added risks and challenges of navigating in minimal light conditions. Here are some things you can expect to see and experience on a sailboat during night-time hours.

The first thing that might catch your attention is the bright light known as a “masthead light” at the top of most sailboats. This light is white and visible for three to six miles in all directions and helps other boats identify the sailboat’s position and direction of travel. Masthead lights differ from the white navigation lights you see on motorboats as they are positioned up high on the mast to enhance visibility.

Sailboats at night are also equipped with red and green navigation lights that tell the boater in which direction the boat is traveling. To make sure they have clear visibility of the horizon, sailors will stay on deck, continuously scanning the water and sky for hazards or other boats.

Aside from navigation, sailboats at night also make sure to have all their safety items in order. The crew, whether they’re racing or cruising, ensures that everyone is wearing appropriate personal flotation devices (PFDs) and that they’re easily accessible should they need them. For added safety, many sailors will also wear headlamps or carry handheld lights, so they can make sure they can see and be seen.

Weather conditions also play a significant role in how sailors prepare their sailboat for night-time sailing. If there’s a potential for fog or other limited visibility conditions, sailors will have additional lights, such as deck lights or spreader lights, set up to make sure they can see the sails and any hazards around them.

Finally, it’s important to mention how spectacular star-gazing is from a sailboat at night. Miles away from city light pollution and with the hum of the boat’s engine in the background, it’s an experience that many sailors cherish. From watching shooting stars to identifying constellations, stargazing is an undeniable perk of sailboat life.

Sailboats don’t stop just because darkness falls. Sailors follow the guidelines of the International Regulations for Preventing Collisions at Sea and make sure their sailboat is equipped with all necessary safety items and lighting to navigate the seas safely at night. If you get the chance to sail at night, we highly recommend it – it’s an experience that shouldn’t be missed!

Related Questions

What type of wood is used for pier pilings, what is the difference between a dock and a floating pier, what is the proper technique for pulling a beginner wakeboarder, what does ‘no wake’ mean on a lake, what is the difference between wash and wake, is wakesurfing possible in the sea, why don’t wooden piers rot, what size wakeboard is needed, how to achieve more pop on a wakeboard, does wake surfing translate to ocean surfing, latest posts, overview of the 2024 sea-doo rxp-x 325, overview of the 2024 parker offshore 2900 cc, what your boat’s beam is and why it matters, power cats of 2024: ultimate guide to the top power catamarans this year, don't miss, our newsletter.

Get the latest boating tips, fishing resources and featured products in your email from BoatingWorld.com!

Navigating the Heat: 10 Safety Tips for a Safe Boat Ride in the Summer Heat

Highs, lows, and tidal know-how: a deep dive into ocean currents, 10 essential tips for fishing near private property, the benefits of using a drift sock: guidance for anglers, lure fishing: secrets for imitating live bait and attracting fish, explore the untapped depths of america’s best bass fishing spots, outboard motor maintenance: tips for keeping your engine in top shape, the essential boat tool kit: tools every boater needs, diy boat building: 8 tips and tricks for building your own vessel, the art of miniature maritime craftsmanship: ship in a bottle, antifouling paints: a guide to keeping your boat shipshape, beginner’s guide to standup paddle boarding: tips and techniques, boating for fitness: how to stay active on the water, kayak safety: how to stay safe on the water, anchoring in a kayak or canoe: how to secure your small boat, overview of the 2024 yamaha 252sd, overview of the 2024 tiara yachts 48 le, overview of the 2024 bass cat jaguar sts, 2024 pursuit os 445: an overview, 2024 aquila 47 molokai review, 2024 sea-doo switch 13 sport review, gear reviews, megabass oneten max lbo jerkbait review, fortress anchors fx-7 anchoring system review, fortress anchors fx-11 anchoring system review, fortress anchors commando anchor kit review, fortress anchors aluminum anchors review, stay in touch.

To be updated with all the latest news, offers and special announcements.

• Privacy Policy