rigging parts sailboat

Sailboat Parts Explained: Illustrated Guide (with Diagrams)

When you first get into sailing, there are a lot of sailboat parts to learn. Scouting for a good guide to all the parts, I couldn't find any, so I wrote one myself.

Below, I'll go over each different sailboat part. And I mean each and every one of them. I'll walk you through them one by one, and explain each part's function. I've also made sure to add good illustrations and clear diagrams.

This article is a great reference for beginners and experienced sailors alike. It's a great starting point, but also a great reference manual. Let's kick off with a quick general overview of the different sailboat parts.

General Overview

The different segments

You can divide up a sailboat in four general segments. These segments are arbitrary (I made them up) but it will help us to understand the parts more quickly. Some are super straightforward and some have a bit more ninja names.

Something like that. You can see the different segments highlighted in this diagram below:

The hull is what most people would consider 'the boat'. It's the part that provides buoyancy and carries everything else: sails, masts, rigging, and so on. Without the hull, there would be no boat. The hull can be divided into different parts: deck, keel, cabin, waterline, bilge, bow, stern, rudder, and many more.

I'll show you those specific parts later on. First, let's move on to the mast.

Sailboats Explained

The mast is the long, standing pole holding the sails. It is typically placed just off-center of a sailboat (a little bit to the front) and gives the sailboat its characteristic shape. The mast is crucial for any sailboat: without a mast, any sailboat would become just a regular boat.

I think this segment speaks mostly for itself. Most modern sailboats you see will have two sails up, but they can carry a variety of other specialty sails. And there are all kinds of sail plans out there, which determine the amount and shape of sails that are used.

The Rigging

This is probably the most complex category of all of them.

Rigging is the means with which the sails are attached to the mast. The rigging consists of all kinds of lines, cables, spars, and hardware. It's the segment with the most different parts.

The most important parts

If you learn anything from this article, here are the most important parts of any sailboat. You will find all of these parts in some shape or form on almost any sailboat.

Okay, we now have a good starting point and a good basic understanding of the different sailboat parts. It's time for the good stuff. We're going to dive into each segment in detail.

Below, I'll go over them one by one, pointing out its different parts on a diagram, listing them with a brief explanation, and showing you examples as well.

After reading this article, you'll recognize every single sailboat part and know them by name. And if you forget one, you're free to look it up in this guide.

On this page:

The hull is the heart of the boat. It's what carries everything: the mast, the sails, the rigging, the passengers. The hull is what provides the sailboat with its buoyancy, allowing it to stay afloat.

Sailboats mostly use displacement hulls, which is a shape that displaces water when moving through it. They are generally very round and use buoyancy to support its own weight. These two characteristics make sure it is a smooth ride.

There are different hull shapes that work and handle differently. If you want to learn more about them, here's the Illustrated Guide to Boat Hull Types (with 11 Examples ). But for now, all we need to know is that the hull is the rounded, floating part of any sailboat.

Instead of simply calling the different sides of a hull front, back, left and right , we use different names in sailing. Let's take a look at them.

The bow is the front part of the hull. It's simply the nautical word for 'front'. It's the pointy bit that cuts through the water. The shape of the bow determines partially how the boat handles.

The stern is the back part of the hull. It's simply the nautical word for 'back'. The shape of the stern partially determines the stability and speed of the boat. With motorboats, the stern lies deep inside the water, and the hull is flatter aft. Aft also means back. This allows it to plane, increasing the hull speed. For sailboats, stability is much more important, so the hull is rounded throughout, increasing its buoyancy and hydrodynamic properties.

The transom is the backplate of the boat's hull. It's the most aft (rear) part of the boat.

Port is the left side of a sailboat.

Starboard is the right side of a sailboat

The bilges are the part where the bottom and the sides of the hull meet. On sailboats, these are typically very round, which helps with hydrodynamics. On powerboats, they tend to have an angle.

The waterline is the point where the boat's hull meets the water. Generally, boat owners paint the waterline and use antifouling paint below it, to protect it from marine growth.

The deck is the top part of the boat's hull. In a way, it's the cap of the boat, and it holds the deck hardware and rigging.

Displacement hulls are very round and smooth, which makes them very efficient and comfortable. But it also makes them very easy to capsize: think of a canoe, for example.

The keel is a large fin that offsets the tendency to capsize by providing counterbalance. Typically, the keel carries ballast in the tip, creating a counterweight to the wind's force on the sails.

The rudder is the horizontal plate at the back of the boat that is used to steer by setting a course and maintaining it. It is connected to the helm or tiller.

Tiller or Helm

• The helm is simply the nautical term for the wheel.
• The tiller is simply the nautical term for the steering stick.

The tiller or helm is attached to the rudder and is used to steer the boat. Most smaller sailboats (below 30') have a tiller, most larger sailboats use a helm. Large ocean-going vessels tend to have two helms.

The cockpit is the recessed part in the deck where the helmsman sits or stands. It tends to have some benches. It houses the outside navigation and systems interfaces, like the compass, chartplotter, and so on. It also houses the mainsheet traveler and winches for the jib. Most boats are set up so that the entire vessel can be operated from the cockpit (hence the name). More on those different parts later.

Most larger boats have some sort of roofed part, which is called the cabin. The cabin is used as a shelter, and on cruising sailboats you'll find the galley for cooking, a bed, bath room, and so on.

The mast is the pole on a sailboat that holds the sails. Sailboats can have one or multiple masts, depending on the mast configuration. Most sailboats have only one or two masts. Three masts or more is less common.

The boom is the horizontal pole on the mast, that holds the mainsail in place.

The sails seem simple, but actually consist of many moving parts. The parts I list below work for most modern sailboats - I mean 90% of them. However, there are all sorts of specialty sails that are not included here, to keep things concise.

The mainsail is the largest sail on the largest mast. Most sailboats use a sloop rigging (just one mast with one bermuda mainsail). In that case, the main is easy to recognize. With other rig types, it gets more difficult, since there can be multiple tall masts and large sails.

If you want to take a look at the different sail plans and rig types that are out there, I suggest reading my previous guide on how to recognize any sailboat here (opens in new tab).

Sail sides:

• Leech - Leech is the name for the back side of the sail, running from the top to the bottom.
• Luff - Luff is the name for the front side of the sail, running from the top to the bottom.
• Foot - Foot is the name for the lower side of the sail, where it meets the boom.

Sail corners:

• Clew - The clew is the lower aft (back) corner of the mainsail, where the leech is connected to the foot. The clew is attached to the boom.
• Tack - The tack is the lower front corner of the mainsail
• Head - The head is the top corner of the mainsail

Battens are horizontal sail reinforcers that flatten and stiffen the sail.

Telltales are small strings that show you whether your sail trim is correct. You'll find telltales on both your jib and mainsail.

The jib is the standard sized headsail on a Bermuda Sloop rig (which is the sail plan most modern sailboats use).

As I mentioned: there are all kinds, types, and shapes of sails. For an overview of the most common sail types, check out my Guide on Sail Types here (with photos).

The rigging is what is used to attach your sails and mast to your boat. Rigging, in other words, mostly consists of all kinds of lines. Lines are just another word for ropes. Come to think of it, sailors really find all kinds of ways to complicate the word rope ...

Two types of rigging

There are two types of rigging: running and standing rigging. The difference between the two is very simple.

• The running rigging is the rigging on a sailboat that's used to operate the sails. For example, the halyard, which is used to lower and heave the mainsail.
• The standing rigging is the rigging that is used to support the mast and sail plan.

Standing Rigging

Here are the different parts that belong to the standing rigging:

• Forestay or Headstay - Line or cable that supports the mast and is attached to the bow of the boat. This is often a steel cable.
• Backstay - Line or cable that supports the mast and is attached to the stern of the boat. This is often a steel cable.
• Sidestay or Shroud - Line or cable that supports the mast from the sides of the boat. Most sailboats use at least two sidestays (one on each side).
• Spreader - The sidestays are spaced to steer clear from the mast using spreaders.

Running Rigging: different words for rope

Ropes play a big part in sailing, and especially in control over the sails. In sailboat jargon, we call ropes 'lines'. But there are some lines with a specific function that have a different name. I think this makes it easier to communicate with your crew: you don't have to define which line you mean. Instead, you simply shout 'mainsheet!'. Yeah, that works.

Running rigging consists of the lines, sheets, and hardware that are used to control, raise, lower, shape and manipulate the sails on a sailboat. Rigging varies for different rig types, but since most sailboats are use a sloop rig, nearly all sailboats use the following running rigging:

• Halyards -'Halyard' is simply the nautical name for lines or ropes that are used to raise and lower the mainsail. The halyard is attached to the top of the mainsail sheet, or the gaffer, which is a top spar that attaches to the mainsail. You'll find halyards on both the mainsail and jib.
• Sheets - 'Sheet' is simply the nautical term for lines or ropes that are used to set the angle of the sail.
• Mainsheet - The line, or sheet, that is used to set the angle of the mainsail. The mainsheet is attached to the Mainsheet traveler. More on that under hardware.
• Jib Sheet - The jib mostly comes with two sheets: one on each side of the mast. This prevents you from having to loosen your sheet, throwing it around the other side of the mast, and tightening it. The jib sheets are often controlled using winches (more on that under hardware).
• Cleats are small on-deck hooks that can be used to tie down sheets and lines after trimming them.
• Reefing lines - Lines that run through the mainsail, used to put a reef in the main.
• The Boom Topping Lift is a line that is attached to the aft (back) end of the boom and runs to the top of the mast. It supports the boom whenever you take down the mainsail.
• The Boom Vang is a line that places downward tension on the boom.

There are some more tensioning lines, but I'll leave them for now. I could probably do an entire guide on the different sheets on a sailboat. Who knows, perhaps I'll write it.

This is a new segment, that I didn't mention before. It's a bit of an odd duck, so I threw all sorts of stuff into this category. But they are just as important as all the other parts. Your hardware consists of cleats, winches, traveler and so on. If you don't know what all of this means, no worries: neither did I. Below, you'll find a complete overview of the different parts.

Deck Hardware

Just a brief mention of the different deck hardware parts:

• Pulpits are fenced platforms on the sailboat's stern and bow, which is why they are called the bow pulpit and stern pulpit here. They typically have a solid steel framing for safety.
• Stanchons are the standing poles supporting the lifeline , which combined for a sort of fencing around the sailboat's deck. On most sailboats, steel and steel cables are used for the stanchons and lifelines.

Mainsheet Traveler

The mainsheet traveler is a rail in the cockpit that is used to control the mainsheet. It helps to lock the mainsheet in place, fixing the mainsails angle to the wind.

If you're interested in learning more about how to use the mainsheet traveler, Matej has written a great list of tips for using your mainsheet traveler the right way . It's a good starting point for beginners.

Winches are mechanical or electronic spools that are used to easily trim lines and sheets. Most sailboats use winches to control the jib sheets. Modern large sailing yachts use electronic winches for nearly all lines. This makes it incredibly easy to trim your lines.

You'll find the compass typically in the cockpit. It's the most old-skool navigation tool out there, but I'm convinced it's also one of the most reliable. In any way, it definitely is the most solid backup navigator you can get for the money.

Want to learn how to use a compass quickly and reliably? It's easy. Just read my step-by-step beginner guide on How To Use a Compass (opens in new tab .

Chartplotter

Most sailboats nowadays use, besides a compass and a map, a chartplotter. Chartplotters are GPS devices that show a map and a course. It's very similar to your normal car navigation.

Outboard motor

Most sailboats have some sort of motor to help out when there's just the slightest breeze. These engines aren't very big or powerful, and most sailboats up to 32' use an outboard motor. You'll find these at the back of the boat.

Most sailboats carry 1 - 3 anchors: one bow anchor (the main one) and two stern anchors. The last two are optional and are mostly used by bluewater cruisers.

I hope this was helpful, and that you've gained a good understanding of the different parts involved in sailing. I wanted to write a good walk-through instead of overwhelming you with lists and lists of nautical terms. I hope I've succeeded. If so, I appreciate any comments and tips below.

I've tried to be as comprehensive as possible, without getting into the real nitty gritty. That would make for a gigantic article. However, if you feel I've left something out that really should be in here, please let me know in the comments below, so I can update the article.

I own a small 20 foot yacht called a Red witch made locally back in the 70s here in Western Australia i found your article great and enjoyed reading it i know it will be a great help for me in my future leaning to sail regards John.

David Gardner

İ think this is a good explanation of the difference between a ”rope” and a ”line”:

Rope is unemployed cordage. In other words, when it is in a coil and has not been assigned a job, it is just a rope.

On the other hand, when you prepare a rope for a specific task, it becomes employed and is a line. The line is labeled by the job it performs; for example, anchor line, dock line, fender line, etc.

Hey Mr. Buckles

I am taking on new crew to race with me on my Flying Scot (19ft dingy). I find your Sailboat Parts Explained to be clear and concise. I believe it will help my new crew learn the language that we use on the boat quickly without being overwhelmed.

PS: my grandparents were from Friesland and emigrated to America.

Thank you Shawn for the well written, clear and easy to digest introductory article. Just after reading this first article I feel excited and ready to set sails and go!! LOL!! Cheers! Daniel.

steve Balog

well done, chap

Great intro. However, the overview diagram misidentifies the cockpit location. The cockpit is located aft of the helm. Your diagram points to a location to the fore of the helm.

William Thompson-Ambrose

An excellent introduction to the basic anatomy and function of the sailboat. Anyone who wants to start sailing should consider the above article before stepping aboard! Thank-you

James Huskisson

Thanks for you efforts mate. We’ve all got to start somewhere. Thanks for sharing. Hoping to my first yacht. 25ft Holland. Would love to cross the Bass Strait one day to Tasmania. 👌 Cheers mate

Alan Alexander Percy

thankyou ijust aquired my first sailboat at 66yrs of age its down at pelican point a beautifull place in virginia usa my sailboat is a redwing 30 if you are ever in the area i wouldnt mind your guidance and superior knowledge of how to sail but iam sure your fantastic article will help my sailboat is wings 30 ft

Thanks for quick refresher course. Having sailed in California for 20+ years I now live in Spain where I have to take a spanish exam for a sailboat license. Problem is, it’s only in spanish. So a lot to learn for an old guy like me.

Very comprehensive, thank you

Your article really brought all the pieces together for me today. I have been adventuring my first sailing voyage for 2 months from the Carolinas and am now in Eleuthera waiting on weather to make the Exumas!!! Great job and thanks

Helen Ballard

I’ve at last found something of an adventure to have in sailing, so I’m starting at the basics, I have done a little sailing but need more despite being over 60 life in the old dog etc, thanks for your information 😊

Barbara Scott

I don’t have a sailboat, neither do l plan to literally take to the waters. But for mental exercise, l have decided to take to sailing in my Bermuda sloop, learning what it takes to become a good sailor and run a tight ship, even if it’s just imaginary. Thank you for helping me on my journey to countless adventures and misadventures, just to keep it out of the doldrums! (I’m a 69 year old African American female who have rediscovered why l enjoyed reading The Adventures of Robert Louis Stevenson as well as his captivating description of sea, wind, sailboat,and sailor).

Great article and very good information source for a beginner like me. But I didn’t find out what I had hoped to, which is, what are all those noisy bits of kit on top of the mast? I know the one with the arrow is a weather vane, but the rest? Many thanks, Jay.

Louis Cohen

The main halyard is attached to the head of the mainsail, not the to the mainsheet. In the USA, we say gaff, not gaffer. The gaff often has its own halyard separate from the main halyard.

Other than that it’s a nice article with good diagrams.

A Girl Who Has an Open Sail Dream

Wow! That was a lot of great detail! Thank you, this is going to help me a lot on my project!

Hi, good info, do u know a book that explains all the systems on a candc 27,

Emma Delaney

As a hobbyist, I was hesitant to invest in expensive CAD software, but CADHOBBY IntelliCAD has proven to be a cost-effective alternative that delivers the same quality and performance.

https://www.cadhobby.com/

Leave a comment

You may also like, guide to understanding sail rig types (with pictures).

There are a lot of different sail rig types and it can be difficult to remember what's what. So I've come up with a system. Let me explain it in this article.

The Ultimate Guide to Sail Types and Rigs (with Pictures)

The Illustrated Guide To Boat Hull Types (11 Examples)

How To Live On a Boat For Free: How I'd Do It

How To Live on a Sailboat: Consider These 5 Things

Own your first boat within a year on any budget.

A sailboat doesn't have to be expensive if you know what you're doing. If you want to learn how to make your sailing dream reality within a year, leave your email and I'll send you free updates . I don't like spam - I will only send helpful content.

Ready to Own Your First Boat?

Just tell us the best email address to send your tips to:

Rigging - Turnbuckles , Toggles , Wire & Rod Components, Norseman Cones & Fittings.

Furling Systems - Systems and replacement parts from a variety of Manufacturers.

Traveller Systems - Adjustable Track Systems for Mainsheet and other applications.

Sailboat Hardware - Rope Clutches, Blocks, Track & Fittings, Winches, etc.

Custom Parts - Custom items, or those out of production or otherwise unavailable.

Consultation - Special projects, research, or information not detailed on-site.

Copyright   1996 - 2024,  Rig-Rite, Inc.        Disclaimer          Web Site maintained by The WATER Group

standing rigging

• rope and line
• cams, cleats and clutches
• head sail gear
• roller furling
• main sail control
• mast hardware
• eye straps and pad eyes
• fairleads and bulls eyes
• anchor and docking
• miscellaneous hardware
• Alexander Roberts
• My Wishlist

• Customer Service
• Order Tracking
• Your Account
• Store Policies & Info
• Privacy Policy
• Helpful Links
• Payment Methods

Shopping Cart: 0 Items

Beginner’s Guide: How To Rig A Sailboat – Step By Step Tutorial

Alex Morgan

Rigging a sailboat is a crucial process that ensures the proper setup and functioning of a sailboat’s various components. Understanding the process and components involved in rigging is essential for any sailor or boat enthusiast. In this article, we will provide a comprehensive guide on how to rig a sailboat.

Introduction to Rigging a Sailboat

Rigging a sailboat refers to the process of setting up the components that enable the sailboat to navigate through the water using wind power. This includes assembling and positioning various parts such as the mast, boom, standing rigging, running rigging, and sails.

Understanding the Components of a Sailboat Rigging

Before diving into the rigging process, it is important to have a good understanding of the key components involved. These components include:

The mast is the tall vertical spar that provides vertical support to the sails and holds them in place.

The boom is the horizontal spar that runs along the bottom edge of the sail and helps control the shape and position of the sail.

• Standing Rigging:

Standing rigging consists of the wires and cables that support and stabilize the mast, keeping it upright.

• Running Rigging:

Running rigging refers to the lines and ropes used to control the sails, such as halyards, sheets, and control lines.

Preparing to Rig a Sailboat

Before rigging a sailboat, there are a few important steps to take. These include:

• Checking the Weather Conditions:

It is crucial to assess the weather conditions before rigging a sailboat. Unfavorable weather, such as high winds or storms, can make rigging unsafe.

• Gathering the Necessary Tools and Equipment:

Make sure to have all the necessary tools and equipment readily available before starting the rigging process. This may include wrenches, hammers, tape, and other common tools.

• Inspecting the Rigging Components:

In the upcoming sections of this article, we will provide a step-by-step guide on how to rig a sailboat, as well as important safety considerations and tips to keep in mind. By following these guidelines, you will be able to rig your sailboat correctly and safely, allowing for a smooth and enjoyable sailing experience.

Key takeaway:

• Rigging a sailboat maximizes efficiency: Proper rigging allows for optimized sailing performance, ensuring the boat moves smoothly through the water.
• Understanding sailboat rigging components: Familiarity with the various parts of a sailboat rigging, such as the mast, boom, and standing and running riggings, is essential for effective rigging setup.
• Importance of safety in sailboat rigging: Ensuring safety is crucial during the rigging process, including wearing a personal flotation device, securing loose ends and lines, and being mindful of overhead power lines.

Get ready to set sail and dive into the fascinating world of sailboat rigging! We’ll embark on a journey to understand the various components that make up a sailboat’s rigging. From the majestic mast to the nimble boom , and the intricate standing rigging to the dynamic running rigging , we’ll explore the crucial elements that ensure smooth sailing. Not forgetting the magnificent sail, which catches the wind and propels us forward. So grab your sea legs and let’s uncover the secrets of sailboat rigging together.

Understanding the mast is crucial when rigging a sailboat. Here are the key components and steps to consider:

1. The mast supports the sails and rigging of the sailboat. It is made of aluminum or carbon fiber .

2. Before stepping the mast , ensure that the area is clear and the boat is stable. Have all necessary tools and equipment ready.

3. Inspect the mast for damage or wear. Check for corrosion , loose fittings , and cracks . Address any issues before proceeding.

4. To step the mast , carefully lift it into an upright position and insert the base into the mast step on the deck of the sailboat.

5. Secure the mast using the appropriate rigging and fasteners . Attach the standing rigging , such as shrouds and stays , to the mast and the boat’s hull .

Fact: The mast of a sailboat is designed to withstand wind resistance and the tension of the rigging for stability and safe sailing.

The boom is an essential part of sailboat rigging. It is a horizontal spar that stretches from the mast to the aft of the boat. Constructed with durable yet lightweight materials like aluminum or carbon fiber, the boom provides crucial support and has control over the shape and position of the sail. It is connected to the mast through a boom gooseneck , allowing it to pivot. One end of the boom is attached to the mainsail, while the other end is equipped with a boom vang or kicker, which manages the tension and angle of the boom. When the sail is raised, the boom is also lifted and positioned horizontally by using the topping lift or lazy jacks.

An incident serves as a warning that emphasizes the significance of properly securing the boom. In strong winds, an improperly fastened boom swung across the deck, resulting in damage to the boat and creating a safety hazard. This incident highlights the importance of correctly installing and securely fastening all rigging components, including the boom, to prevent accidents and damage.

3. Standing Rigging

When rigging a sailboat, the standing rigging plays a vital role in providing stability and support to the mast . It consists of several key components, including the mast itself, along with the shrouds , forestay , backstay , and intermediate shrouds .

The mast, a vertical pole , acts as the primary support structure for the sails and the standing rigging. Connected to the top of the mast are the shrouds , which are cables or wires that extend to the sides of the boat, providing essential lateral support .

The forestay is another vital piece of the standing rigging. It is a cable or wire that runs from the top of the mast to the bow of the boat, ensuring forward support . Similarly, the backstay , also a cable or wire, runs from the mast’s top to the stern of the boat, providing important backward support .

To further enhance the rig’s stability , intermediate shrouds are installed. These additional cables or wires are positioned between the main shrouds, as well as the forestay or backstay. They offer extra support , strengthening the standing rigging system.

Regular inspections of the standing rigging are essential to detect any signs of wear, such as fraying or corrosion . It is crucial to ensure that all connections within the rig are tight and secure, to uphold its integrity. Should any issues be identified, immediate attention must be given to prevent accidents or damage to the boat. Prioritizing safety is of utmost importance when rigging a sailboat, thereby necessitating proper maintenance of the standing rigging. This ensures a safe and enjoyable sailing experience.

Note: <p> tags have been kept intact.

4. Running Rigging

Running Rigging

When rigging a sailboat, the running rigging is essential for controlling the sails and adjusting their position. It is important to consider several aspects when dealing with the running rigging.

1. Choose the right rope: The running rigging typically consists of ropes with varying properties such as strength, stretch, and durability. Weather conditions and sailboat size should be considered when selecting the appropriate rope.

2. Inspect and maintain the running rigging: Regularly check for signs of wear, fraying, or damage. To ensure safety and efficiency, replace worn-out ropes.

3. Learn essential knot tying techniques: Having knowledge of knots like the bowline, cleat hitch, and reef knot is crucial for securing the running rigging and adjusting sails.

4. Understand different controls: The running rigging includes controls such as halyards, sheets, and control lines. Familiarize yourself with their functions and proper usage to effectively control sail position and tension.

5. Practice proper sail trimming: Adjusting the tension of the running rigging significantly affects sailboat performance. Mastering sail trimming techniques will help optimize sail shape and maximize speed.

By considering these factors and mastering running rigging techniques, you can enhance your sailing experience and ensure the safe operation of your sailboat.

The sail is the central component of sailboat rigging as it effectively harnesses the power of the wind to propel the boat.

When considering the sail, there are several key aspects to keep in mind:

– Material: Sails are typically constructed from durable and lightweight materials such as Dacron or polyester. These materials provide strength and resistance to various weather conditions.

– Shape: The shape of the sail plays a critical role in its overall performance. A well-shaped sail should have a smooth and aerodynamic profile, which allows for maximum efficiency in capturing wind power.

– Size: The size of the sail is determined by its sail area, which is measured in square feet or square meters. Larger sails have the ability to generate more power, but they require greater skill and experience to handle effectively.

– Reefing: Reefing is the process of reducing the sail’s size to adapt to strong winds. Sails equipped with reefing points allow sailors to decrease the sail area, providing better control in challenging weather conditions.

– Types: There are various types of sails, each specifically designed for different purposes. Common sail types include mainsails, jibs, genoas, spinnakers, and storm sails. Each type possesses its own unique characteristics and is utilized under specific wind conditions.

Understanding the sail and its characteristics is vital for sailors, as it directly influences the boat’s speed, maneuverability, and overall safety on the water.

Getting ready to rig a sailboat requires careful preparation and attention to detail. In this section, we’ll dive into the essential steps you need to take before setting sail. From checking the weather conditions to gathering the necessary tools and equipment, and inspecting the rigging components, we’ll ensure that you’re fully equipped to navigate the open waters with confidence. So, let’s get started on our journey to successfully rigging a sailboat!

1. Checking the Weather Conditions

Checking the weather conditions is crucial before rigging a sailboat for a safe and enjoyable sailing experience. Monitoring the wind speed is important in order to assess the ideal sailing conditions . By checking the wind speed forecast , you can determine if the wind is strong or light . Strong winds can make sailboat control difficult, while very light winds can result in slow progress.

Another important factor to consider is the wind direction . Assessing the wind direction is crucial for route planning and sail adjustment. Favorable wind direction helps propel the sailboat efficiently, making your sailing experience more enjoyable.

In addition to wind speed and direction, it is also important to consider weather patterns . Keep an eye out for impending storms or heavy rain. It is best to avoid sailing in severe weather conditions that may pose a safety risk. Safety should always be a top priority when venturing out on a sailboat.

Another aspect to consider is visibility . Ensure good visibility by checking for fog, haze, or any other conditions that may hinder navigation. Clear visibility is important for being aware of other boats and potential obstacles that may come your way.

Be aware of the local conditions . Take into account factors such as sea breezes, coastal influences, or tidal currents. These local factors greatly affect sailboat performance and safety. By considering all of these elements, you can have a successful and enjoyable sailing experience.

Here’s a true story to emphasize the importance of checking the weather conditions. One sunny afternoon, a group of friends decided to go sailing. Before heading out, they took the time to check the weather conditions. They noticed that the wind speed was expected to be around 10 knots, which was perfect for their sailboat. The wind direction was coming from the northwest, allowing for a pleasant upwind journey. With clear visibility and no approaching storms, they set out confidently, enjoying a smooth and exhilarating sail. This positive experience was made possible by their careful attention to checking the weather conditions beforehand.

2. Gathering the Necessary Tools and Equipment

To efficiently gather all of the necessary tools and equipment for rigging a sailboat, follow these simple steps:

• First and foremost, carefully inspect your toolbox to ensure that you have all of the basic tools such as wrenches, screwdrivers, and pliers.
• Make sure to check if you have a tape measure or ruler available as they are essential for precise measurements of ropes or cables.
• Don’t forget to include a sharp knife or rope cutter in your arsenal as they will come in handy for cutting ropes or cables to the desired lengths.
• Gather all the required rigging hardware including shackles, pulleys, cleats, and turnbuckles.
• It is always prudent to check for spare ropes or cables in case replacements are needed during the rigging process.
• If needed, consider having a sailing knife or marlinspike tool for splicing ropes or cables.
• For rigging a larger sailboat, it is crucial to have a mast crane or hoist to assist with stepping the mast.
• Ensure that you have a ladder or some other means of reaching higher parts of the sailboat, such as the top of the mast.

Once, during the preparation of rigging my sailboat, I had a moment of realization when I discovered that I had forgotten to bring a screwdriver . This unfortunate predicament occurred while I was in a remote location with no nearby stores. Being resourceful, I improvised by utilizing a multipurpose tool with a small knife blade, which served as a makeshift screwdriver. Although it was not the ideal solution, it allowed me to accomplish the task. Since that incident, I have learned the importance of double-checking my toolbox before commencing any rigging endeavor. This practice ensures that I have all of the necessary tools and equipment, preventing any unexpected surprises along the way.

3. Inspecting the Rigging Components

Inspecting the rigging components is essential for rigging a sailboat safely. Here is a step-by-step guide on inspecting the rigging components:

1. Visually inspect the mast, boom, and standing rigging for damage, such as corrosion, cracks, or loose fittings.

2. Check the tension of the standing rigging using a tension gauge. It should be within the recommended range from the manufacturer.

3. Examine the turnbuckles, clevis pins, and shackles for wear or deformation. Replace any damaged or worn-out hardware.

4. Inspect the running rigging, including halyards and sheets, for fraying, signs of wear, or weak spots. Replace any worn-out lines.

5. Check the sail for tears, wear, or missing hardware such as grommets or luff tape.

6. Pay attention to the connections between the standing rigging and the mast. Ensure secure connections without any loose or missing cotter pins or rigging screws.

7. Inspect all fittings, such as mast steps, spreader brackets, and tangs, to ensure they are securely fastened and in good condition.

8. Conduct a sea trial to assess the rigging’s performance and make necessary adjustments.

Regularly inspecting the rigging components is crucial for maintaining the sailboat’s rigging system’s integrity, ensuring safe sailing conditions, and preventing accidents or failures at sea.

Once, I went sailing on a friend’s boat without inspecting the rigging components beforehand. While at sea, a sudden gust of wind caused one of the shrouds to snap. Fortunately, no one was hurt, but we had to cut the sail loose and carefully return to the marina. This incident taught me the importance of inspecting the rigging components before sailing to avoid unforeseen dangers.

Step-by-Step Guide on How to Rig a Sailboat

Get ready to set sail with our step-by-step guide on rigging a sailboat ! We’ll take you through the process from start to finish, covering everything from stepping the mast to setting up the running rigging . Learn the essential techniques and tips for each sub-section, including attaching the standing rigging and installing the boom and sails . Whether you’re a seasoned sailor or a beginner, this guide will have you ready to navigate the open waters with confidence .

1. Stepping the Mast

To step the mast of a sailboat, follow these steps:

1. Prepare the mast: Position the mast near the base of the boat.

2. Attach the base plate: Securely fasten the base plate to the designated area on the boat.

3. Insert the mast step: Lower the mast step into the base plate and align it with the holes or slots.

4. Secure the mast step: Use fastening screws or bolts to fix the mast step in place.

5. Raise the mast: Lift the mast upright with the help of one or more crew members.

6. Align the mast: Adjust the mast so that it is straight and aligned with the boat’s centerline.

7. Attach the shrouds: Connect the shrouds to the upper section of the mast, ensuring proper tension.

8. Secure the forestay: Attach the forestay to the bow of the boat, ensuring it is securely fastened.

9. Final adjustments: Check the tension of the shrouds and forestay, making any necessary rigging adjustments.

Following these steps ensures that the mast is properly stepped and securely in place, allowing for a safe and efficient rigging process. Always prioritize safety precautions and follow manufacturer guidelines for your specific sailboat model.

2. Attaching the Standing Rigging

To attach the standing rigging on a sailboat, commence by preparing the essential tools and equipment, including wire cutters, crimping tools, and turnbuckles.

Next, carefully inspect the standing rigging components for any indications of wear or damage.

After inspection, fasten the bottom ends of the shrouds and stays to the chainplates on the deck.

Then, securely affix the top ends of the shrouds and stays to the mast using adjustable turnbuckles .

To ensure proper tension, adjust the turnbuckles accordingly until the mast is upright and centered.

Utilize a tension gauge to measure the tension in the standing rigging, aiming for around 15-20% of the breaking strength of the rigging wire.

Double-check all connections and fittings to verify their security and proper tightness.

It is crucial to regularly inspect the standing rigging for any signs of wear or fatigue and make any necessary adjustments or replacements.

By diligently following these steps, you can effectively attach the standing rigging on your sailboat, ensuring its stability and safety while on the water.

3. Installing the Boom and Sails

To successfully complete the installation of the boom and sails on a sailboat, follow these steps:

1. Begin by securely attaching the boom to the mast. Slide it into the gooseneck fitting and ensure it is firmly fastened using a boom vang or another appropriate mechanism.

2. Next, attach the main sail to the boom. Slide the luff of the sail into the mast track and securely fix it in place using sail slides or cars.

3. Connect the mainsheet to the boom. One end should be attached to the boom while the other end is connected to a block or cleat on the boat.

4. Proceed to attach the jib or genoa. Make sure to securely attach the hanks or furler line to the forestay to ensure stability.

5. Connect the jib sheets. One end of each jib sheet should be attached to the clew of the jib or genoa, while the other end is connected to a block or winch on the boat.

6. Before setting sail, it is essential to thoroughly inspect all lines and connections. Ensure that they are properly tensioned and that all connections are securely fastened.

During my own experience of installing the boom and sails on my sailboat, I unexpectedly encountered a strong gust of wind. As a result, the boom began swinging uncontrollably, requiring me to quickly secure it to prevent any damage. This particular incident served as a vital reminder of the significance of properly attaching and securing the boom, as well as the importance of being prepared for unforeseen weather conditions while rigging a sailboat.

4. Setting Up the Running Rigging

Setting up the running rigging on a sailboat involves several important steps. First, attach the halyard securely to the head of the sail. Then, connect the sheets to the clew of the sail. If necessary, make sure to secure the reefing lines . Attach the outhaul line to the clew of the sail and connect the downhaul line to the tack of the sail. It is crucial to ensure that all lines are properly cleated and organized. Take a moment to double-check the tension and alignment of each line. If you are using a roller furling system, carefully wrap the line around the furling drum and securely fasten it. Perform a thorough visual inspection of the running rigging to check for any signs of wear or damage. Properly setting up the running rigging is essential for safe and efficient sailing. It allows for precise control of the sail’s position and shape, ultimately optimizing the boat’s performance on the water.

Safety Considerations and Tips

When it comes to rigging a sailboat, safety should always be our top priority. In this section, we’ll explore essential safety considerations and share some valuable tips to ensure smooth sailing. From the importance of wearing a personal flotation device to securing loose ends and lines, and being cautious around overhead power lines, we’ll equip you with the knowledge and awareness needed for a safe and enjoyable sailing experience. So, let’s set sail and dive into the world of safety on the water!

1. Always Wear a Personal Flotation Device

When rigging a sailboat, it is crucial to prioritize safety and always wear a personal flotation device ( PFD ). Follow these steps to properly use a PFD:

• Select the appropriate Coast Guard-approved PFD that fits your size and weight.
• Put on the PFD correctly by placing your arms through the armholes and securing all the straps for a snug fit .
• Adjust the PFD for comfort , ensuring it is neither too tight nor too loose, allowing freedom of movement and adequate buoyancy .
• Regularly inspect the PFD for any signs of wear or damage, such as tears or broken straps, and replace any damaged PFDs immediately .
• Always wear your PFD when on or near the water, even if you are a strong swimmer .

By always wearing a personal flotation device and following these steps, you will ensure your safety and reduce the risk of accidents while rigging a sailboat. Remember, prioritize safety when enjoying water activities.

2. Secure Loose Ends and Lines

Inspect lines and ropes for frayed or damaged areas. Secure loose ends and lines with knots or appropriate cleats or clamps. Ensure all lines are properly tensioned to prevent loosening during sailing. Double-check all connections and attachments for security. Use additional safety measures like extra knots or stopper knots to prevent line slippage.

To ensure a safe sailing experience , it is crucial to secure loose ends and lines properly . Neglecting this important step can lead to accidents or damage to the sailboat. By inspecting, securing, and tensioning lines , you can have peace of mind knowing that everything is in place. Replace or repair any compromised lines or ropes promptly. Securing loose ends and lines allows for worry-free sailing trips .

3. Be Mindful of Overhead Power Lines

When rigging a sailboat, it is crucial to be mindful of overhead power lines for safety. It is important to survey the area for power lines before rigging the sailboat. Maintain a safe distance of at least 10 feet from power lines. It is crucial to avoid hoisting tall masts or long antenna systems near power lines to prevent contact. Lower the mast and tall structures when passing under a power line to minimize the risk of contact. It is also essential to be cautious in areas where power lines run over the water and steer clear to prevent accidents.

A true story emphasizes the importance of being mindful of overhead power lines. In this case, a group of sailors disregarded safety precautions and their sailboat’s mast made contact with a low-hanging power line, resulting in a dangerous electrical shock. Fortunately, no serious injuries occurred, but it serves as a stark reminder of the need to be aware of power lines while rigging a sailboat.

Some Facts About How To Rig A Sailboat:

• ✅ Small sailboat rigging projects can improve sailing performance and save money. (Source: stingysailor.com)
• ✅ Rigging guides are available for small sailboats, providing instructions and tips for rigging. (Source: westcoastsailing.net)
• ✅ Running rigging includes lines used to control and trim the sails, such as halyards and sheets. (Source: sailingellidah.com)
• ✅ Hardware used in sailboat rigging includes winches, blocks, and furling systems. (Source: sailingellidah.com)
• ✅ A step-by-step guide can help beginners rig a small sailboat for sailing. (Source: tripsavvy.com)

Frequently Asked Questions

1. how do i rig a small sailboat.

To rig a small sailboat, follow these steps: – Install or check the rudder, ensuring it is firmly attached. – Attach or check the tiller, the long steering arm mounted to the rudder. – Attach the jib halyard by connecting the halyard shackle to the head of the sail and the grommet in the tack to the bottom of the forestay. – Hank on the jib by attaching the hanks of the sail to the forestay one at a time. – Run the jib sheets by tying or shackling them to the clew of the sail and running them back to the cockpit. – Attach the mainsail by spreading it out and attaching the halyard shackle to the head of the sail. – Secure the tack, clew, and foot of the mainsail to the boom using various lines and mechanisms. – Insert the mainsail slugs into the mast groove, gradually raising the mainsail as the slugs are inserted. – Cleat the main halyard and lower the centerboard into the water. – Raise the jib by pulling down on the jib halyard and cleating it on the other side of the mast. – Tighten the mainsheet and one jibsheet to adjust the sails and start moving forward.

2. What are the different types of sailboat rigs?

Sailboat rigs can be classified into three main types: – Sloop rig: This rig has a single mast with a mainsail and a headsail, typically a jib or genoa. – Cutter rig: This rig has two headsails, a smaller jib or staysail closer to the mast, and a larger headsail, usually a genoa, forward of it, alongside a mainsail. – Ketch rig: This rig has two masts, with the main mast taller than the mizzen mast. It usually has a mainsail, headsail, and a mizzen sail. Each rig has distinct characteristics and is suitable for different sailing conditions and preferences.

3. What are the essential parts of a sailboat?

The essential parts of a sailboat include: – Mast: The tall vertical spar that supports the sails. – Boom: The horizontal spar connected to the mast, which extends outward and supports the foot of the mainsail. – Rudder: The underwater appendage that steers the boat. – Centerboard or keel: A retractable or fixed fin-like structure that provides stability and prevents sideways drift. – Sails: The fabric structures that capture the wind’s energy to propel the boat. – Running rigging: The lines or ropes used to control the sails and sailing equipment. – Standing rigging: The wires and cables that support the mast and reinforce the spars. These are the basic components necessary for the functioning of a sailboat.

4. What is a spinnaker halyard?

A spinnaker halyard is a line used to hoist and control a spinnaker sail. The spinnaker is a large, lightweight sail that is used for downwind sailing or reaching in moderate to strong winds. The halyard attaches to the head of the spinnaker and is used to raise it to the top of the mast. Once hoisted, the spinnaker halyard can be adjusted to control the tension and shape of the sail.

5. Why is it important to maintain and replace worn running rigging?

It is important to maintain and replace worn running rigging for several reasons: – Safety: Worn or damaged rigging can compromise the integrity and stability of the boat, posing a safety risk to both crew and vessel. – Performance: Worn rigging can affect the efficiency and performance of the sails, diminishing the boat’s speed and maneuverability. – Reliability: Aging or worn rigging is more prone to failure, which can lead to unexpected problems and breakdowns. Regular inspection and replacement of worn running rigging is essential to ensure the safe and efficient operation of a sailboat.

6. Where can I find sailboat rigging books or guides?

There are several sources where you can find sailboat rigging books or guides: – Online: Websites such as West Coast Sailing and Stingy Sailor offer downloadable rigging guides for different sailboat models. – Bookstores: Many bookstores carry a wide selection of boating and sailing books, including those specifically focused on sailboat rigging. – Sailing schools and clubs: Local sailing schools or yacht clubs often have resources available for learning about sailboat rigging. – Manufacturers: Some sailboat manufacturers, like Hobie Cat and RS Sailing, provide rigging guides for their specific sailboat models. Consulting these resources can provide valuable information and instructions for rigging your sailboat properly.

About the author

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Save my name, email, and website in this browser for the next time I comment.

Latest posts

The history of sailing – from ancient times to modern adventures

History of Sailing Sailing is a time-honored tradition that has evolved over millennia, from its humble beginnings as a means of transportation to a beloved modern-day recreational activity. The history of sailing is a fascinating journey that spans cultures and centuries, rich in innovation and adventure. In this article, we’ll explore the remarkable evolution of…

Sailing Solo: Adventures and Challenges of Single-Handed Sailing

Solo Sailing Sailing has always been a pursuit of freedom, adventure, and self-discovery. While sailing with a crew is a fantastic experience, there’s a unique allure to sailing solo – just you, the wind, and the open sea. Single-handed sailing, as it’s often called, is a journey of self-reliance, resilience, and the ultimate test of…

Sustainable Sailing: Eco-Friendly Practices on the boat

Eco Friendly Sailing Sailing is an exhilarating and timeless way to explore the beauty of the open water, but it’s important to remember that our oceans and environment need our protection. Sustainable sailing, which involves eco-friendly practices and mindful decision-making, allows sailors to enjoy their adventures while minimizing their impact on the environment. In this…

Sailboat Running Rigging

You don't want to have faulty sailboat running rigging. Strong, durable lines are essential for controlling the sails on your boat without risking your own safety, or that of the sails. Our sailboat ropes and lines were designed to withstand any weather condition without fraying, tearing, or catching. When you are ready to trim and hoist your sails, you can rest assured that the sailboat rigging equipment that you purchase from us will provide the smoothest and fastest transitions. From tack to jibe, our sailboat halyards and mainsheets make it easy, durable and always the right choice.

Order our sailboat running rigging lines today for fast, free shipping on qualifying orders, and rig up your boat with the most trusted sailboat riggings around!

Lines by type of sailing

• Club/Racing
• Dinghy/One Design
• Kite & Surf

Lines by Application*

• Jib/Genoa Sheets
• Spinnaker Sheets
• * Sailboat lines selector by application.

Lines by Material

• Polyester Double Braid
• Dyneema Single Braid
• Dyneema Double Braid
• Vectran Core Double Braid
• Dyneema Core Double Braid

Lines by Brand

• Alpha Ropes
• FSE Robline
• G&B Ropes
• New England
• Yale Cordage

Our sailboat rigging include mainsail halyards, spinnaker halyards, and Genoa halyards that are made from a double braid polyester line, double braid Dyneema line or Vectran. Our mainsheets are also made from durable double braid polyester and hybrid fibers with blend of Dyneema and Technora. This material has the best reputation in the industry.

* Visit our quick sailboat lines selector by application.

• Billing Terms and Conditions
• Shipping and Return Policy
• Shopping Cart

Parts of a Sailboat Rigging: A Comprehensive Guide

by Emma Sullivan | Aug 6, 2023 | Sailboat Maintenance

Short answer: Parts of a Sailboat Rigging

The sailboat rigging consists of various components essential for controlling and supporting the sails. Key parts include the mast, boom, shrouds, forestay, backstay, halyards, and sheets.

Understanding the Basics: A Comprehensive Overview of the Parts of a Sailboat Rigging

Title: Understanding the Basics: A Comprehensive Overview of the Parts of a Sailboat Rigging

Introduction: Sailboats have been a symbol of freedom and adventure for centuries. Whether you are an avid sailor or an aspiring skipper, understanding the various components that make up a sailboat rigging is essential. In this insightful guide, we will dive into the world of sailboat rigging, unraveling its intricacies while shedding light on its importance and functionality. So tighten your mainsails and let’s set sail on this knowledge-packed journey!

1. Mast: The mast is the vertical spar that supports the sails . It provides structural integrity to the entire rigging system and enables harnessing wind power effectively. Constructed from materials such as aluminum or carbon fiber, modern masts are designed to be lightweight yet robust enough to withstand varying weather conditions .

2. Standing Rigging: The standing rigging refers to all fixed parts that support the mast. This includes stays (fore, back, and jumper) which run between the masthead and various points on the hull or deck, like chainplates or tangs. Shrouds (cap shrouds, intermediate shrouds) help counteract lateral forces by providing lateral support to prevent excessive sideward movement of the mast.

3. Running Rigging: Unlike standing rigging, running rigging comprises lines that control sails’ deployment and trim dynamically during sailing maneuvers . The halyard raises or lowers a sail along its respective track within the mast groove while keeping it securely fastened in place when needed.

4. Sails: Of course, we can’t discuss sailboat rigging without mentioning sails themselves! They are like wings for your boat – converting wind energy into forward motion efficiently . Main sails typically attach through slides onto a mast track using luff cars for easy hoisting and lowering during different conditions.

5. Boom: The boom plays a crucial role in sail control , as it connects the aft end of the mainsail to the mast. By controlling the angle of the boom, sailors can adjust the shape and trim of the main sail for optimum performance against varying wind conditions.

6. Spreader: Spreader arms are horizontal poles extending from some point up the mast’s length. They serve two purposes: keeping shrouds apart to improve sail shape and reducing compressive loads on the rigging by forcing them away from each other.

7. Turnbuckles: Turnbuckles are adjustable devices used to tension standing rigging elements such as shrouds and stays. These fittings allow sailors to fine-tune rigging tensions while maximizing stability and overall performance based on prevailing weather conditions.

8. Winches: Winches are mechanical devices primarily used for easing or trimming running rigging lines under high loads. With a simple rotation, winches convert human effort into mechanical advantage, allowing efficient handling of lines for adjusting sails in different situations.

Conclusion: Understanding your sailboat rigging is not just essential for safe sailing but also for harnessing its maximum potential during every voyage. From deciphering various components like masts, standing and running rigging, booms, spreaders, turnbuckles, and winches – each element plays a crucial role in ensuring a smooth sailing experience. So next time you find yourself out on open waters, take a moment to appreciate these intricate systems that keep you powered by nothing but wind!

Step by Step Guide: How to Properly Assemble and Install the Various Parts of a Sailboat Rigging

Welcome fellow sailors and enthusiasts! Today, we are diving into the intricate world of sailboat rigging. Whether you are an experienced sailor or a newcomer to the sailing community, understanding how to properly assemble and install the various parts of a sailboat rig is essential for smooth and safe sailing. So, grab your tools and let’s get started on this step-by-step guide !

Step 1: Gather Your Tools and Materials Before embarking on this rigging journey, it’s crucial to have all your tools and materials ready. Here is a list of essentials you’ll need:

– Stainless steel wire rigging – Turnbuckles – Fittings and hardware such as clevis pins, shackles, and thimbles – Measuring tape or ruler – Wire cutters – Crimping tool or swaging machine (depending on your preference) – Electric drill (if required) – Lubricant or anti-seize compound

Make sure you have everything organized before starting. A well-prepared sailor is a successful one!

Step 2: Inspect Existing Rigging (If Applicable) If you own a used boat or are replacing old rigging, take some time to inspect the current setup. Look out for any signs of wear, frayed wires, or damaged fittings. It’s crucial to address these issues before proceeding with installation as they can compromise safety at sea.

Step 3: Measure Twice; Cut Once! Now that everything is set up let’s proceed by measuring the length needed for each piece of wire rigging carefully. Tinier inaccuracies in measurement during this step can lead to major inconveniences later.

Ensure you give yourself ample space for adjusting tension using turnbuckles. Pro-tip: It’s better to cut the wire slightly longer than needed rather than cutting it too short!

Step 4: Attach Fittings – The Devil Lies in Details Once you have measured and cut the rigging wire, let’s start attaching the fittings. This is where precision comes into play. Begin with inserting thimbles onto each end of the wires to avoid kinks or fraying. Next, connect the turnbuckles and fittings according to your sailboat’s specific rigging plan.

Step 5: Tension Matters Now that you have installed all the necessary fittings, it’s time to tension the rigging. This step requires a bit of finesse as over-tightening can damage equipment, while under-tightening can compromise performance.

Using a tension gauge, ensure that you achieve optimal tension on all parts of your sailboat’s rigging. It might take some trial and error, but finding that sweet spot is worth it!

Step 6: Inspect and Lubricate Before setting sail , always double-check everything! Look for any loose fittings or signs of wear once again. You wouldn’t want to go through these steps all over again out in the middle of nowhere!

Additionally, apply lubricant or anti-seize compound to prevent corrosion and ensure smooth operation of turnbuckles and other moving parts.

And there you have it – a professionally and properly assembled sailboat rigging! Sit back for a minute or two to appreciate your workmanship before feeling that excitement rush through as you’ll soon set sail smoothly onto those horizon-stretching waters.

Remember, practice makes perfect when it comes to mastering this skill. Over time, you’ll develop your own techniques and become a maestro at sailboat rigging assembly. Happy sailing!

Top Frequently Asked Questions about Sailboat Rigging Components Answered

Are you new to sailing or considering purchasing a sailboat? No matter your experience level, understanding the rigging components of a sailboat is crucial for safe and successful navigation on the water. In this blog post, we aim to answer some of the top frequently asked questions about sailboat rigging components. So, let’s dive in!

1. What are sailboat rigging components? Sailboat rigging components refer to the various parts and systems that help support and control the sails on a sailboat. These components include standing rigging (the fixed parts) and running rigging (lines that can be adjusted). Some common examples of rigging components are the mast, boom, shrouds, stays, halyards, sheets, and blocks.

2. What is the purpose of each rigging component? Each component serves a specific purpose in sailing . The mast supports the sails and provides leverage for controlling their shape. The boom holds down the bottom of the mainsail and allows adjustment for different points of sail . Shrouds provide lateral support to prevent excessive side-to-side movement of the mast. Stays offer fore-and-aft support to keep the mast from leaning too far forward or backward. Halyards raise and lower sails while sheets control their angle in relation to wind direction.

3. How often should I inspect my sailboat’s rigging ? Regular inspection is crucial for ensuring your safety on the water . We recommend conducting visual inspections before every sailing trip and more thorough inspections at least once a year or per manufacturer recommendations. Look out for any signs of wear, corrosion, loose fittings, or frayed lines that may indicate potential issues.

4. Can I replace my own rigging components? While minor repairs or adjustments can typically be done by boat owners with some knowledge and experience, replacing major rigging components should ideally be done by professionals who specialize in sailboat rigging services. They have the expertise and equipment necessary to properly install and tension components, ensuring your safety.

5. How long do sailboat rigging components typically last? The lifespan of rigging components depends on various factors such as usage, maintenance, and exposure to environmental conditions. Stainless steel stays can last for 10-15 years or longer with regular inspections and maintenance, while synthetic running rigging (such as ropes made from high-performance fibers) may have a shorter lifespan of 3-5 years.

6. Are there any safety tips related to sailboat rigging? Absolutely! Always wear appropriate personal protective equipment when working with or near rigging components. Take care not to overload or overstress the rig by correctly tensioning lines within manufacturer specifications . Avoid standing under or in close proximity to the mast while raising or lowering it, as it can be dangerous if it accidentally drops.

7. What are some common signs of rigging failure? Rigging failures can be catastrophic, so being able to identify potential issues is vital. Look out for visible cracks, rust, elongation, broken strands on wires, loose fittings, excessive wear on ropes, or unusual noises while sailing. Any of these signs should prompt an immediate inspection and possible replacement of affected components.

In conclusion, understanding sailboat rigging components is crucial for any sailor looking to navigate safely on the water. By familiarizing yourself with these frequently asked questions and following proper inspection and maintenance practices, you’ll enjoy a smooth sailing experience while prioritizing your safety at all times!

Exploring the Essential Components: An In-Depth Look at Key Parts of a Sailboat Rigging

Sailing is a thrilling and age-old activity that has fascinated adventurers and seafarers for centuries. At the heart of every sailing vessel lies its rigging, which is a complex system of ropes, wires, and equipment that hold the sails in place and allows for precise control over the boat’s movement. In this blog post, we will take an in-depth look at the key components of a sailboat rigging to understand their importance and how they contribute to the overall sailing experience.

Mast: The backbone of any sailboat rigging is its mast. This tall vertical structure supports the sails and provides stability to the vessel . Made from materials such as aluminum or carbon fiber, masts are designed to withstand strong winds and carry considerable loads. They come in various shapes and sizes depending on the type of boat and intended use.

Boom: Attached horizontally towards the bottom of the mast, the boom serves as a critical component in controlling the position of the mainsail – typically the largest sail on board. Acting as an extension of the mast, it allows for adjustments in sail trim by pivoting up or down.

Shrouds: These sturdy wire cables are attached to either side of the mast at multiple levels, forming a crucial part of sailboat rigging’s structural integrity. Shrouds keep the mast upright by counteracting lateral forces created by wind pressure on sails . Adjustable tensioning systems enable sailors to fine-tune shroud tension according to prevailing conditions.

Stay: Similar to shrouds but located further forward on most boats, stays provide additional support for maintaining mast stability. Fore-stay runs from top-to-bow while back-stays run from top-to-aft; together they prevent excessive forward or aft bending movements during intense wind pressures.

Turnbuckles: Within sailboat rigging systems lie turnbuckles – mechanical devices used for adjusting tension in wires or ropes like shrouds or stays. These clever devices simplify the task of tightening or loosening rigging components, enabling sailors to optimize sail shape and boat performance with ease.

Halyards: Essential for hoisting sails up and down, halyards are ropes used to control the vertical movement of the sails . They are typically operated through winches, which increase mechanical advantage and make raising and lowering large sails manageable.

Blocks: Also known as pulleys, these simple yet crucial devices help redirect the path of ropes within a sailboat rigging system. Blocks increase mechanical advantage by changing the direction of applied force, making it easier for sailors to control different aspects such as sail trim or adjusting tension.

Running Rigging vs Standing Rigging: Sailboat rigging can be classified into two main categories – running rigging and standing rigging. Running rigging refers to all movable lines and ropes that control sail position, while standing rigging encompasses all stationary components that give structure to the mast. Both elements work in harmony to ensure efficient maneuverability and safety at sea .

Understanding these key components within a sailboat’s rigging is essential for any aspiring sailor or seasoned mariner alike. It not only allows them to appreciate how these intricately designed systems function together but also helps enhance their sailing skills by leveraging each component’s unique role.

So next time you set foot on a sailboat or watch one glide gracefully across the water, take a moment to admire the finely tuned rigging – a mesmerizing web of interconnected parts that enable humans to harness the power of wind and embark on unforgettable nautical adventures.

The Crucial Role of Each Part: Unveiling the Functionality and Importance of Sailboat Rigging Components

Sailboat rigging components may seem simple and insignificant at first glance, but anyone who has sailed knows just how crucial each part is to the overall functionality and performance of a sailboat. From the mast to the shrouds, every component plays a vital role in ensuring safe navigation, efficient sailing, and maximum performance on the water.

One of the most essential parts of any sailboat rigging system is the mast. Serving as the backbone of the entire structure, the mast provides vertical stability and supports various sails that catch the wind . The mast’s height and shape significantly impact a boat’s performance, affecting not only its speed but also its ability to handle different wind conditions. A sturdy mast ensures that forces are properly distributed throughout the rigging system, preventing excessive strain or potential failure.

Connected to both sides of the mast are what are known as shrouds. These cables or wires act as primary support structures for restraining lateral movement and maintaining balance in heavy winds. Shrouds come in different sizes and tensions depending on factors such as sail size and boat length. Proper tensioning of shrouds is crucial for maintaining structural integrity and minimizing flexing under intense force.

Another integral part is the forestay – a cable or wire running from near or at the top of the mast down to the bow area of a sailboat . The forestay supports forward strength and controls stay sag- an essential factor for optimizing aerodynamics by shaping how sails interact with wind. It helps maintain proper sail geometry while limiting unnecessary heel (leaning) during maneuvers or gusts.

The backstay is another component critical for stability and control. Running from either side of the stern up to near or at the top of the mast, it helps counterbalance fore-aft bending forces created by wind pressure against a boat’s sails pushing it forward. By adjusting backstay tension, sailors can fine-tune their boat’s responsiveness to changes in wind speed or balance.

The boom, a horizontal spar attached to the mast, plays a crucial role in controlling the angle and shape of the mainsail. It acts as a pivot point for adjusting sail trim, allowing sailors to maximize lift and minimize drag based on wind conditions. With its connection to the gooseneck at the foot of the mast, it enables easy raising and lowering of the mainsail for quick adjustments or docking maneuvers .

Moreover, various blocks and pulleys are scattered throughout a sailboat’s rigging system playing essential roles in creating mechanical advantages. These components reduce friction and redirect forces generated by sails and lines during sailing operations, making it easier for sailors to handle heavy loads while preserving their energy. Choosing high-quality blocks with low-friction bearings is crucial for efficient sail handling while maintaining control.

Understanding how each part functions individually is significant; but more importantly, appreciating how they work in harmony is where true seamanship resides. Rigging components must be designed and maintained carefully to ensure safety, performance, and optimal functionality on any sailing adventure.

In conclusion, sailboat rigging components may appear simple to some extent but hold tremendous importance in enhancing a boat’s capabilities on water. From providing vertical stability with masts and dampening lateral movement with shrouds to shaping sails’ interaction with wind using forestays and backstays – every component has a crucial role to play. Understanding how these parts function individually and collectively helps sailors navigate safely while maximizing performance out on the open sea

Troubleshooting Tips: Common Issues and Solutions related to different parts of a sailboat rigging

Introduction: The rigging of a sailboat is an essential component that allows for safe navigation and optimal performance on the water. However, like any mechanical system, it can experience issues from time to time. In this blog post, we will provide detailed professional troubleshooting tips for common problems related to various parts of a sailboat rigging. Whether you’re an experienced sailor or just starting out, these solutions will help keep your rigging in top shape and ensure smooth sailing on every adventure.

1. Mast and Standing Rigging: One common issue sailors face is the presence of squeaking noises coming from the mast or standing rigging while underway. This can be quite bothersome and distracting during a peaceful sail. To resolve this problem, start by checking the connections between different components of the rigging and tighten any loose fittings appropriately. Additionally, using lubricants specifically designed for marine environments can significantly reduce friction between movable parts, eliminating annoying creaks and groans as you ride the waves.

2. Shrouds and Forestay: Another issue frequently encountered involves misaligned shrouds or forestay tension that affects the overall stability of the mast. If you notice your mast leaning slightly to one side or backward, it’s likely due to incorrectly adjusted shrouds or an improperly tensioned forestay. To rectify this, use a tension gauge to ensure consistent tension across all shrouds while avoiding excessive strain on either side of the mast base. By maintaining proper alignment and equal tension distribution, your rigging will provide maximum support when experiencing strong winds or rough conditions.

3. Running Rigging (Lines): Running rigging encompasses all lines used for controlling sails such as halyards, sheets, and control lines – crucial elements for proper sail handling. A typical problem associated with running rigging is line chafing caused by repeated friction against sharp edges or abrasive surfaces onboard. Inspect your lines regularly for signs of wear, paying close attention to areas exposed to constant rubbing. To prevent chafing, secure protective coverings or install specialized guards where necessary. Regularly washing and lubricating your lines will also extend their lifespan and ensure smooth operation.

4. Block and Tackle Systems: Block and tackle systems play a vital role in distributing loads and facilitating the movement of sails, particularly in larger sailboats. A common issue arises when blocks become jammed or fail to rotate freely due to debris buildup or lack of proper maintenance. To address this problem, inspect all blocks systematically, disassembling them if required, and clean out any accumulated dirt or salt crystals thoroughly. After cleaning, applying a liberal amount of marine-grade grease will promote smooth rotation and reduce the likelihood of future blockages.

Conclusion: Effective troubleshooting is essential for maintaining a sailboat rigging system that performs optimally and ensures a safe experience on the water. By following these detailed professional tips, you can address common issues associated with different parts of your sailboat rigging promptly and efficiently. Remember to conduct regular inspections, prioritize preventive maintenance, and seek professional assistance whenever needed. With a well-maintained rigging system at your disposal, you can embark on each sailing journey confidently, knowing that you’re prepared to overcome any challenges that may arise along the way.

Recent Posts

• Sailboat Gear and Equipment
• Sailboat Lifestyle
• Sailboat Maintenance
• Sailboat Racing
• Sailboat Tips and Tricks
• Sailboat Types
• Sailing Adventures
• Sailing Destinations
• Sailing Safety
• Sailing Techniques

Open to the Public!

• Sailing Supplies

Sailboat Rigging

Ronstan Split Cotter Ring - 18.8mm(3/4") ID

Split Cotter Ring - 18.8mm(3/4") IDSuits clevis pins RF260 - RF274Grade 316 Stainless Steel

Ronstan Drain Plug Only - Plastic Nylon

Drain Plug Only - Plastic NylonFeatures:Plug to suit RF294 & RF737Water tight sealRetaining legsUV Stabilized Nylon plug Specifications:Color: Black/RedBox Dimensions: 1"H x 1"W x 2"L WT: 0.05 lbsUPC: 9316800031252

Ronstan Split Cotter Ring - 25mm(1") ID

Split Cotter Ring - 25mm(1") IDSuits clevis pins RF267 - RF278Grade 316 Stainless Steel

Sea Dog Rail Mount Fairlead w/ Stainless Insert

Sea Dog Rail Mount Fairlead w/ Stainless Insert The Sea Dog Rail Mount Fairlead features a injection-molded nylon fairlead with stainless insert. Allows easy routing of roller furling lines, and the stainless insert allows use of wire lines if necessary...

Ronstan Sail Slide - Internal Track - 22mm(7/8") Wide x 42mm(1-21/32") Long

Sail Slide - Internal Track - 22mm(7/8") Wide x 42mm(1-21/32") LongImpact Resistant, U.V. Stabilized NylonWhite Specifications:Color: WhiteBox Dimensions: 1"H x 1"W x 2"L WT: 0.1 lbsUPC: 9316800210787

Ronstan Split Cotter Ring - 14mm(5/8") ID

Split Cotter Ring - 14mm(5/8") IDSuits clevis pins RF260 - RF274Grade 316 Stainless Steel

Ronstan Split Ring - 11mm(7/16") Diameter

Split Ring - 11mm(7/16") DiameterSuits Clevis Pins RF260-RF266

Whitecap Rubber Spreader Boot - Pair - Medium - White

Rubber Spreader Boot - Pair - Medium - WhiteFeatures:White Rubber Spreader BootMedium Spread Insert: 1" - 2"Stay Insert: 3/16"Length: 2-3/8"Height: 5-3/4"

Ronstan Drain Plug & Housing - Coarse Thread - Black Nylon

Drain Plug & Housing - Coarse Thread - Black NylonFeatures:24mm(15/16") Hole DiameterWater tight sealRetaining legsUV Stabilized Nylon plug and housing Specifications:Color: Black/RedBox Dimensions: 1"H x 2"W x 3"L WT: 0.1 lbsUPC:...

Ronstan Twist On Jib Hank - 3mm(1/8") Wire

Twist On Jib Hank - 3mm(1/8") WirePiston hanks includes screws.Applications:Suitable for Keelboat, Dinghy and Trailerable yacht jibsMaterials:Impact resistant, U.V. stablised Nylon Specifications:Color: WhiteBox Dimensions: 1"H x 1"W x...

Ronstan Race Acetal Sheave - 39mm(1-1/2") OD

Race Acetal Sheave Solid Bearing - 39mm(1-1/2") ODFeatures:High strength & durability, utilizing the self-lubricating properties of Acetal

Ronstan Utility Line Hanger - 2-Pack

Utility Line Hanger - 2-PackU.V. and impact resistant Nylon construction

Ronstan Split Ring - 10mm(3/8") Diameter

Split Ring - 10mm(3/8") DiameterSuits Clevis Pins RF258-RF266

Whitecap Rubber Spreader Boot - Pair - Large - White

Rubber Spreader Boot - Pair - Large - WhiteFeatures:White Rubber Spreader BootLarge Spreader Insert: 2" - 3"Stay Insert: 3/16"Length: 2-7/8"Height: 7-1/2"

Ronstan Nylon Tiller Extension Retaining Clip - 16mm(5/8") - Black

Nylon Tiller Extension Retaining Clip - 16mm(5/8") - BlackU.V. Stabilized NylonSuits 16mm(5/8") Diameter Tube Specifications:Type: TillerBox Dimensions: 1"H x 2"W x 3"L WT: 0.1 lbsUPC: 9316800266623

Whitecap Rubber Spreader Boot - Pair - Small - White

Rubber Spreader Boot - Pair - Small - WhiteFeatures:White Rubber Spreader BootSmall Spreader Insert: 1/2" - 1-1/2"Stay Insert: 1/8" Length: 1-5/8"Height: 2"

Ronstan Race Sheave - Acetal Solid Bearing - 28mm(1-1/8") OD

Race Sheave - Acetal Ball Bearing - 28mm(1-1/8") ODPrecision moulded Acetal sheaves running on Acetal or Torlon® ball bearings provide high performance & low friction.Acetal Sheaves:Choice of bearingsSolid bearing - high strength and durability,...

Ronstan Sister Clip - Stainless Steel - Large

Sister Clip - Stainless Steel - LargeEffective means of quickly attaching and detaching ropes58.0mm(2-1/4") Length Specifications:Color: StainlessBox Dimensions: 1"H x 1"W x 2"L WT: 0.3 lbsUPC: 9316800053315

Ronstan Splicing Kit

Splicing KitThese five Selma Fids are all you need to splice different sizes and types of rope or line. Features:Highly polished stainless steel Fid sizes: 4, 5.5, 7.5, 10, and 13 mm Splice double and hollow braided lines from 1/8" to 9/16" Splice...

FSE Robline Waxed Tackle Yarn Whipping Twine Kit w/Needle - Blue - 0.8mm x 80M

Waxed Tackle Yarn Whipping Twine w/Needle - Blue - 0.8mm x 80MWhipping Twine With High Wax Content w/Sailmaker NeedleAvailable as twisted twine, it is braided and will not open because of the flat, strong seem. The special wax formula makes this whipping...

You can’t get the wind in your sails without the proper sailboat rigging. Wholesale Marine carries every component recreational sailors and racers require to maintain their rigging including snatch blocks, shock line, thimbles, rope grips, spinnaker poles, whipping twine, reefing kits, sheave boxes, parrel beads, quick links, Lazy Jack kits, mast supports, line hangers, piston hanks, splicing kits and so much more!

Select from the top names in the business: Barton Marine , FSE Robline , Ronstan , Sea Dog Marine , and Whitecap Industries . It doesn’t matter if you just want FSE Robline’s Waxed Tackle Yarn Whipping Twine , simple Parrel Beads , a Splicing Kit , a Snatch Block Alloy Sheave, or a Single Line Reefing Kit . Every customer receives the same welcome and customer service. We also offer competitive prices, same day, flat rate shipping, and returns are always easy.

Wholesale Marine stocks everything boaters, including sailors, require to protect their investment. Give us a call to discuss your needs or to place an order. We’re here Monday through Friday, from 9:00 AM until 6:00 PM EST at (877) 388-2628. When you call, be sure to sign up for our Captain’s Club Rewards Program . This way you’ll save even more the next time you shop at Wholesale Marine.

Oops, something went wrong. Please try again.

You are now logged in!

No products in the cart.

Sailing Ellidah is supported by our readers. Buying through our links may earn us an affiliate commission at no extra cost to you.

The Standing Rigging On A Sailboat Explained

The standing rigging on a sailboat is a system of stainless steel wires that holds the mast upright and supports the spars.

In this guide, I’ll explain the basics of a sailboat’s hardware and rigging, how it works, and why it is a fundamental and vital part of the vessel. We’ll look at the different parts of the rig, where they are located, and their function.

We will also peek at a couple of different types of rigs and their variations to determine their differences. In the end, I will explain some additional terms and answer some practical questions I often get asked.

But first off, it is essential to understand what standing rigging is and its purpose on a sailboat.

The purpose of the standing rigging

Like I said in the beginning, the standing rigging on a sailboat is a system of stainless steel wires that holds the mast upright and supports the spars. When sailing, the rig helps transfer wind forces from the sails to the boat’s structure. This is critical for maintaining the stability and performance of the vessel.

The rig can also consist of other materials, such as synthetic lines or steel rods, yet its purpose is the same. But more on that later.

Since the rig supports the mast, you’ll need to ensure that it is always in appropriate condition before taking your boat out to sea. Let me give you an example from a recent experience.

Dismasting horrors

I had a company inspect the entire rig on my sailboat while preparing for an Atlantic crossing. The rigger didn’t find any issues, but I decided to replace the rig anyway because of its unknown age. I wanted to do the job myself so I could learn how it is done correctly.

Not long after, we left Gibraltar and sailed through rough weather for eight days before arriving in Las Palmas. We were safe and sound and didn’t experience any issues. Unfortunately, several other boats arriving before us had suffered rig failures. They lost their masts and sails—a sorrowful sight but also a reminder of how vital the rigging is on a sailboat.

The most common types of rigging on a sailboat

The most commonly used rig type on modern sailing boats is the fore-and-aft Bermuda Sloop rig with one mast and just one headsail. Closely follows the Cutter rig and the Ketch rig. They all have a relatively simple rigging layout. Still, there are several variations and differences in how they are set up.

A sloop has a single mast, and the Ketch has one main mast and an additional shorter mizzen mast further aft. A Cutter rig is similar to the Bermuda Sloop with an additional cutter forestay, allowing it to fly two overlapping headsails.

You can learn more about the differences and the different types of sails they use in this guide. For now, we’ll focus on the Bermuda rig.

The difference between standing rigging and running rigging

Sometimes things can get confusing as some of our nautical terms are used for multiple items depending on the context. Let me clarify just briefly:

The  rig  or  rigging  on a sailboat is a common term for two parts:

• The  standing rigging  consists of wires supporting the mast on a sailboat and reinforcing the spars from the force of the sails when sailing.
• The  running rigging  consists of the halyards, sheets, and lines we use to hoist, lower, operate, and control the sails on a sailboat.

Check out my guide on running rigging here !

The difference between a fractional and a masthead rig

A Bermuda rig is split into two groups. The  Masthead  rig and the  Fractional  rig.

The  Masthead  rig has a forestay running from the bow to the top of the mast, and the spreaders point 90 degrees to the sides. A boat with a masthead rig typically carries a bigger overlapping headsail ( Genoa)  and a smaller mainsail. Very typical on the Sloop, Ketch, and Cutter rigs.

A  Fractional  rig has forestays running from the bow to 1/4 – 1/8 from the top of the mast, and the spreaders are swept backward. A boat with a fractional rig also has the mast farther forward than a masthead rig, a bigger mainsail, and a smaller headsail, usually a Jib. Very typical on more performance-oriented sailboats.

There are exceptions in regards to the type of headsail, though. Many performance cruisers use a Genoa instead of a Jib , making the difference smaller.

Some people also fit an inner forestay, or a babystay, to allow flying a smaller staysail.

Explaining the parts and hardware of the standing rigging

The rigging on a sailing vessel relies on stays and shrouds in addition to many hardware parts to secure the mast properly. And we also have nautical terms for each of them. Since a system relies on every aspect of it to be in equally good condition, we want to familiarize ourselves with each part and understand its function.

Forestay and Backstay

The  forestay  is a wire that runs from the bow to the top of the mast. Some boats, like the Cutter rig, can have several additional inner forestays in different configurations.

The  backstay  is the wire that runs from the back of the boat to the top of the mast. Backstays have a tensioner, often hydraulic, to increase the tension when sailing upwind. Some rigs, like the Cutter, have running backstays and sometimes checkstays or runners, to support the rig.

The primary purpose of the forestay and backstay is to prevent the mast from moving fore and aft. The tensioner on the backstay also allows us to trim and tune the rig to get a better shape of the sails.

The shrouds are the wires or lines used on modern sailboats and yachts to support the mast from sideways motion.

There are usually four shrouds on each side of the vessel. They are connected to the side of the mast and run down to turnbuckles attached through toggles to the chainplates bolted on the deck.

• Cap shrouds run from the top of the mast to the deck, passing through the tips of the upper spreaders.
• Intermediate shrouds  run from the lower part of the mast to the deck, passing through the lower set of spreaders.
• Lower shrouds  are connected to the mast under the first spreader and run down to the deck – one fore and one aft on each side of the boat.

This configuration is called continuous rigging. We won’t go into the discontinuous rigging used on bigger boats in this guide, but if you are interested, you can read more about it here .

Shroud materials

Shrouds are usually made of 1 x 19 stainless steel wire. These wires are strong and relatively easy to install but are prone to stretch and corrosion to a certain degree. Another option is using stainless steel rods.

Rod rigging

Rod rigging has a stretch coefficient lower than wire but is more expensive and can be intricate to install. Alternatively, synthetic rigging is becoming more popular as it weighs less than wire and rods.

Synthetic rigging

Fibers like Dyneema and other aramids are lightweight and provide ultra-high tensile strength. However, they are expensive and much more vulnerable to chafing and UV damage than other options. In my opinion, they are best suited for racing and regatta-oriented sailboats.

Wire rigging

I recommend sticking to the classic 316-graded stainless steel wire rigging for cruising sailboats. It is also the most reasonable of the options. If you find yourself in trouble far from home, you are more likely to find replacement wire than another complex rigging type.

Relevant terms on sailboat rigging and hardware

The spreaders are the fins or wings that space the shrouds away from the mast. Most sailboats have at least one set, but some also have two or three. Once a vessel has more than three pairs of spreaders, we are probably talking about a big sailing yacht.

A turnbuckle is the fitting that connects the shrouds to the toggle and chainplate on the deck. These are adjustable, allowing you to tension the rig.

A chainplate is a metal plate bolted to a strong point on the deck or side of the hull. It is usually reinforced with a backing plate underneath to withstand the tension from the shrouds.

The term mast head should be distinct from the term masthead rigging. Out of context, the mast head is the top of the mast.

A toggle is a hardware fitting to connect the turnbuckles on the shrouds and the chainplate.

How tight should the standing rigging be?

It is essential to periodically check the tension of the standing rigging and make adjustments to ensure it is appropriately set. If the rig is too loose, it allows the mast to sway excessively, making the boat perform poorly.

You also risk applying a snatch load during a tack or a gybe which can damage the rig. On the other hand, if the standing rigging is too tight, it can strain the rig and the hull and lead to structural failure.

The standing rigging should be tightened enough to prevent the mast from bending sideways under any point of sail. If you can move the mast by pulling the cap shrouds by hand, the rigging is too loose and should be tensioned. Once the cap shrouds are tightened, follow up with the intermediates and finish with the lower shrouds. It is critical to tension the rig evenly on both sides.

The next you want to do is to take the boat out for a trip. Ensure that the mast isn’t bending over to the leeward side when you are sailing. A little movement in the leeward shrouds is normal, but they shouldn’t swing around. If the mast bends to the leeward side under load, the windward shrouds need to be tightened. Check the shrouds while sailing on both starboard and port tack.

Once the mast is in a column at any point of sail, your rigging should be tight and ready for action.

If you feel uncomfortable adjusting your rig, get a professional rigger to inspect and reset it.

How often should the standing rigging be replaced on a sailboat?

I asked the rigger who produced my new rig for Ellidah about how long I could expect my new rig to last, and he replied with the following:

The standing rigging should be replaced after 10 – 15 years, depending on how hard and often the boat has sailed. If it is well maintained and the vessel has sailed conservatively, it will probably last more than 20 years. However, corrosion or cracked strands indicate that the rig or parts are due for replacement regardless of age.

If you plan on doing extended offshore sailing and don’t know the age of your rig, I recommend replacing it even if it looks fine. This can be done without removing the mast from the boat while it is still in the water.

How much does it cost to replace the standing rigging?

The cost of replacing the standing rigging will vary greatly depending on the size of your boat and the location you get the job done. For my 41 feet sloop, I did most of the installation myself and paid approximately $4700 for the entire rig replacement.

Can Dyneema be used for standing rigging?

Dyneema is a durable synthetic fiber that can be used for standing rigging. Its low weight, and high tensile strength makes it especially popular amongst racers. Many cruisers also carry Dyneema onboard as spare parts for failing rigging.

How long does dyneema standing rigging last?

Dyneema rigging can outlast wire rigging if it doesn’t chafe on anything sharp. There are reports of Dyneema rigging lasting as long as 15 years, but manufacturers like Colligo claim their PVC shrink-wrapped lines should last 8 to 10 years. You can read more here .

Final words

Congratulations! By now, you should have a much better understanding of standing rigging on a sailboat. We’ve covered its purpose and its importance for performance and safety. While many types of rigs and variations exist, the hardware and concepts are often similar. Now it’s time to put your newfound knowledge into practice and set sail!

Or, if you’re not ready just yet, I recommend heading over to my following guide to learn more about running rigging on a sailboat.

Sharing is caring!

Skipper, Electrician and ROV Pilot

Robin is the founder and owner of Sailing Ellidah and has been living on his sailboat since 2019. He is currently on a journey to sail around the world and is passionate about writing his story and helpful content to inspire others who share his interest in sailing.

Very well written. Common sense layout with just enough photos and sketches. I enjoyed reading this article.

Thank you for the kind words.

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Free Shipping Over $99* - 366 Day Returns - Dedicated Customer Support

• Call Us +1-503-285-5536
• Sign in & Register
• Recently Viewed

General Parts

General Parts, Fittings, and Accessories for Small Sailboats. We offer a full range of sailboat hardware, blocks, cleats, shackles, dollies and trailers, accessories, and more. These parts are not necessarily specific to any one model of sailboat, but rather are general fittings that often work on a variety of boats for a variety of applications. 

• Qty in Cart

Ronstan Horn Cleat 8 Inch

Ronstan Horn Cleat 6-1/2 Inch

Ronstan Horn Cleat 5 Inch

Ronstan Horn Cleat 4 Inch

Ronstan Horn Cleat 3 Inch

Fabric Guard Waterproofing Spray

Dynamic Dollies Dock Cradle

Dynamic Combo Rail System Rack Over and Spar Deck Double Tongue Dolly

Dynamic Combo Rail System Rack Over and Spar Deck Single Tongue Dolly

Dynamic Combo Rail System Rack Over Double Tongue Dolly

Dynamic Combo Rail System Rack Over Single Tongue Dolly

Dynamic Combo Rail System Double Tongue Dolly

Dynamic Combo Rail System Single Tongue Dolly

Gill Marine Tool

Gill Harness Rescue Tool

ILCA Cunningham / Outhaul Upgrade Kit Harken

• Total: items /
• Add all to cart

Adding your products to cart

Subscribe to our newsletter.

Sign up for our newsletter to receive exclusive discounts, new product announcements, and upcoming sales.

JIB FURLING GEAR

• CDI Flexible
• Furling Accessories
• Racing Foils
• Whisker and Spinnaker

MAIN SAIL FURLING and REEFING

• Boom Furlers
• Reefing and LazyJacks

MAIN SAIL TRACK SYSTEMS

Standing rigging.

• Swage Terminals and Toggles
• Turnbuckles
• Backstay Adjusters
• Inner Forestay Tools...
• Miscellaneous Hardware
• Measuring Guide
• Hardware and Wire

RUNNING RIGGING

• Rope Clutches
• Cam and Standard Cleats
• Pad Eyes, Eye Straps
• Rachet, Snatch, Wire
• Halyard Lift
• Accessories
• rigid vangs
• tackle vangs

GROUND TACKLE

Mast climbing.

• ATN Top Climber

RADAR MOUNTS AND REFLECTORS

Welcome to rigging only.

Our www.riggingandhardware.com shop on line site is now open for business. We now have most manufacture's parts up and running. Pricing is current on the riggingandhardware.com site. Pictures and selection guides are rather lacking at this time but we are working on them and will be loading more product and manufacturers asap. As always, don't hesitate to contact us with any questions or to place an order at [email protected] or call (508) 992-0434.

Our Mission

• We now stock and swage wire up to 5/8 diameter for sailboat standing rigging and architectural wire projects. Larger sizes are available.
• We now stock and swage wire up to 5/8 diameter for standing rigging and architectural projects. Larger sizes are available.
• Metric wire and swage fittings are available for standing rigging applications. We are able to provide swaged standing rigging assemblies as well as mechanical terminals (assembled or you assemble) to meet your needs at an affordable cost. Current stock is 8-10-12mm. Note the bulk of these fittings will have imperial pin and thread dimensions.

Return Policy

Customer comments.

• We thank you and your staff for your help and advise. We are enjoying sailing more with the furler. M.&R. G., Chicago
• All arrived safely and perfectly on time. The lifelines are almost too pretty to put on the boat and it's a damn pretty boat. The shrouds and backstay are superb and a perfect fit. If anyone ever wants a referral about Rigging Only tell them to contact me. R. A. , Curator, N. C.
• Just a quick note to tell you how grateful I am. The order was waiting for me when I arrived as promised. All the parts were of top quality and the prices were more than reasonable. I am recommending the services and products of Rigging Only to all my fellow charter captains of the Virgin Islands Charter League. Capt. G. F. USVI
• Due to your excellent quality, service, and prices on my previous order I would like to get a price quote and estimated turnaround time for replacing my current standing rigging... B. S. Gurnee, IL.
• Got them on time! Many Thanks! C. S. Lacombe, LA

Contact Information

• Skerry Scale Model
• Wherry Scale Model
• Dory Scale Model
• Bevin's Skiff Scale Model Kit
• Autumn Leaves
• Lake Union Swift
• Faering Cruiser
• Madness Proa
• Outrigger Junior
• Skerry Raid
• Waterlust Sailing Canoe
• Whitby Pilot Gig
• Rhode Runner Runabout
• Wharram Mana 24
• CLC Teardrop Camper
• Assembled Teardrop Camper
• Recreational
• Performance
• Light Touring
• Traditional Canoes
• Decked Canoes
• Lighthouse Tender Peapod
• Jimmy Skiff II
• Tenderly Dinghy
• Northeaster Dory
• Southwester Dory
• Passagemaker Dinghies
• Eastport Prams
• Sailing Dinghies
• Kayak-Canoe Sailrig
• Pacific Proas
• Independence R/C Model
• Peeler Skiff
• Rhode Runner
• Cocktail Class Racer
• Oxford Shell II
• Chester Yawl
• Fixed Seat Rowing
• Sliding Seat Rowing
• Annapolis Wherry Tandem
• Expedition Wherry
• Annapolis Wherry
• Bevin Skiff
• Cradle Boat
• Stand-Up Paddleboards
• Prone Paddleboards
• Surf Kayaks
• Grain Surfboards
• W17 Trimaran
• Gemini & Telstar Centerboards
• Kayak Plans
• Canoe Plans
• Sailboat Plans
• Rowboat Plans
• Powerboat Plans
• Paddleboard Plans
• Downloadable Plans
• Stitch & Glue Designs
• Strip-Planked Designs
• Hybrid Designs
• Night Herons
• Other Strippers
• Microbootleggers
• Mill Creek Hybrid
• Shearwater Hybrids
• Wood Duck Hybrids
• Chesapeakes
• Shearwaters
• Mill Creeks
• Petrel Play SG
• Night Heron SG
• Sit On Top Kayak
• Arctic Hawk

• Overstock & Closeouts
• Boatbuilding Deals
• New Plans Sets
• New Supplies
• T-Shirts & Caps
• Scale Model Kits
• Modeling Tools
• Gift Certificates
• Small Projects
• Gift Ideas for Sailors
• Gift Ideas for SUPers
• Gift Ideas for Rowers
• Gift Ideas for Paddlers
• Gift Ideas for Campers
• Safety Gear
• NRS Camping Gear
• NRS Boating Gear
• Rowing Gear
• Seats & Foam
• Paddling Gear
• Rope & Cordage
• Sailing Gear
• Custom Boat Covers
• Transport & Storage
• Footbraces & Rudders
• MALONE Auto Racks
• THULE Roof Racks
• TRAILEX Trailers
• HARKEN Hardware
• WERNER Paddles
• Customize Your Boat
• Boatbuilding Tools
• Finishing Supplies
• Paint & Varnish
• PETTIT Paint & Varnish
• INTERLUX Paint & Varnish
• Epoxy & Fiberglass
• Composite Supplies
• MAS Epoxies
• WEST SYSTEM Epoxy
• Fasteners & Hardware
• Bronze & Brass Hardware
• Rigging Hardware
• Plywood & Cedar Strips
• Marine Lumber: Regular Stock
• Inlays & Onlays
• Vinyl Lettering
• Camper Accessories
• Camper Door Hardware
• Camper Hatch Hardware
• Camper Electrical Hardware
• Factory Sale

• Mar 25-Apr 6: Teardrop Camper (MD)
• Apr 8-13: Jimmy Skiff II (MD)
• Apr 13: Intro to Epoxy (Sponsored by CLC) (WA)
• Apr 15-20: Annapolis Wherry (MD)
• Apr 22-27: Introduction to Stitch-and-Glue Boatbuilding (WA)
• Apr 27: Make Your Own Greenland Paddle
• May 6-11: Stitch-and-Glue Kayak (Shearwater or Wood Duck) (MD)
• May 11: Intro to Epoxy (Sponsored by CLC) (WA)
• May 20-25: Jimmy Skiff II (WA)
• Jun 3-8: Northeaster Dory (MD)
• Jun 10-15: Skerry Daysailer (WA)
• Jun 16-22: Annapolis Wherry (ME)
• Jun 17: Champlain Discovery Teen Expeditions (VT)
• Jun 23-29: Building a Hybrid Kayak (ME)
• Jun 30-Jul 6: Sassafras Canoe (ME)
• Jun 30-Jul 6: Remote Control Sailing Model (ME)
• Jul 7-13: Lapstrake Dinghy (ME)
• Jul 14-20: Skerry Daysailer (ME)
• Jul 15-27: Teardrop Camper (MD)
• Jul 15-21: Stitch-and-Glue Kayak (Shearwater or Wood Duck) or Stand-Up Paddleboard (WA)
• Aug 5-10: Northeaster Dory (WA)
• Aug 11-17: Stitch & Glue Boatbuilding with John Harris (ME)
• Aug 26-31: Lapstrake Dinghy (WA)
• Sep 1-7: Annapolis Wherry (ME)
• Sep 8-14: Shearwater or Wood Duck Sea Kayak (ME)
• Sep 16-21: Annapolis Wherry (WA)
• Sep 16-21: Skerry Daysailer (MD)
• Sep 23-28: Lapstrake Dinghy (MD)
• Sep 30-Oct 25: Chesapeake Light Craft Workshop Takeover (WA)
• Sep 30-Oct 11: Teardrop Camper (MD)
• Oct 21-26: Tenderly Dinghy (MD)
• Nov 4-9: Chester Yawl (MD)

• Photo Contest Winners: December 31st, 2023
• Design Spotlight: Petrel Play SG
• Photo Contest Winners: September 2023
• 2023 Calfornia Boatbuilder Rendezvous
• CLC Photo Contest Open for Entries!
• Cool New Teardrop Camper Video
• 2023 Big Little Boat Festival Recap - Part 1
• Strip Kit Update: More Western Red & Alaskan Yellow Cedar!
• CLC Partners with Jackman Works and Arbortech to Build a CLC Teardrop Camper
• Top Tools, and Why You Need Them
• Browse the Archives . . .
• May 18: Big Little Boat Festival 2024
• Jun 28-30: WoodenBoat Show at Mystic Seaport
• Sep 6-8: The Wooden Boat Festival in Port Townsend, WA
• Oct 5: Mid-Atlantic Small Craft Festival
• Apr 20: Sail & Sell: A Maritime Market Collective
• Oct 10-14: Annapolis Sailboat Show
• A Midwinter PocketShip Cruise
• Three Hulls: A Sailing Outrigger for Adventures Near and Far
• Lugs and Jibs: An Update on Autumn Leaves
• Ollie: Another Pretty Canoe Yawl for Sailing Purists
• "Small Wooden Boat Design": A Panel Discussion
• The Sharpie That Got Away
• Modifying a Northeaster Dory for Camp-Cruising
• Encore, Autumn Leaves: The Canoe Yawl Sails
• The Most Peculiar Client
• WoodenBoat Magazine #256: 'Marine Plywood: A Consumer's Guide'
• Browse all Articles . . .
• Arbortech Tools
• Boatbuilding Schools
• Box of Rain
• Jackman Works
• Small Boats Magazine
• Xyla Foxlin

Essential items for rigging small sailboats.  Sail slides and shackles, wire shrouds, thimbles and swages, and aluminum tubing.

Sail Track, 5/8" Stainless

Our Stainless Sail Track is roll formed for precision and strength.  To fasten the track to your mast we recommend #6 stainless steel round head screws that are at least 3/4" long.  The holes for fastening are pre drilled in...

from $38.95

5/8" Sail Slide, Shackle & Protector

Shackles are designed for ease of use, high strength and the ability to absorb shock loads, with potectors.  High-strength nickel alloy and stainless-steel sail slides are used.  Choose single components or a complet set from...

5/8" External Sail Slide

These sail slides can be stitched directly to you sail or they can be attached to grommets in your sail with a shackle. 

5/8" Nylon External Sail Track Stop

The nylon adjustable track stop allows you to feed sail slides on to external sail track, then lock the slides onto the track.  Made in the USA 

1/8" White Solid Braided Nylon Rope

Shock absorbent nylon blend. Recommended for securing boats, cargo and furniture. Great for lashing line on Sail Rigs. Strong, abrasion resistant. Flexible, easy to knot. Won't rot or mildew. Resists oils, gas and most chemicals. Smooth....

Finish Line by New England Ropes

Finish Line by New England Ropes Strongest Pre-Stretch Line on the market for dinghy & one design racing. Perfect all around polyester pre-stretch line for all of your dinghy and small boat sailing needs. Features: Cover: Polyester...

Spun Classic by New England Ropes Spun Classic

SPUN CLASSIC Ideal for a traditional look and feel! For a traditional look and feel, a conventional 3-strand spun polyester rope, Spun Classic is a soft, free running rope that resists jamming and kinkin. Strong, good looking and performs in all...

New England Ropes Spyder Line with Dyneema Core

This dinghy control line got its name because of its spider web-like strength thanks to its Dyneema core and twill pattern(smooth) cover.  Spyder Line is just the right small diameter line needed for higher load applications.  It is very...

New England Ropes HTS-78

Grand Prix Racing  HTS-78 Dyneema 12-Strand Single Braid HTS-78 features 100% Dyneema® fiber.  Features: Material: Dyneema® SK78 12 Strand Single Braid Specific Gravity - .97 UV Resistant Applications:...

Sta-Set by New England Ropes

STA-SET by New England RopesThe #1 Double Braid in America! Sta-Set is the quintessential proven performance double braid with superior durability and dependability. Sta-Set is a strong, flexible and long wearing line. It is high strength, low...

Vintage Sta-Set by New England Ropes

Vintage Sta-Set Ideal for use aboard traditional vessels. The #1 double braid in America is now available in a traditional classic shade. High strength, low stretch, extremely durable, Vintage Sta-Set still remains soft over time. It is...

Sta-Set X by New England Ropes

THE PERFECT CRUISING LEVEL HALYARD LINE The strongest and lowest stretch polyester line available with a patented parallel fiber core and a braided cover made from a blend of spun and filament polyester. Excellent value as an ideal replacement...

5/8" Stainless Steel External Sail Track Stop

The adjustable track stop allows you to feed sail slides on to external sail track, then lock the slides onto the track.

5/8" End Stop

This 5/8" stainless steel End Stop is used at he top of our Stainless Sail Track to prevent the sail from riding off the track. 

Small Craft Shrouds

Stainless steel rigging wire cut to the proper length with loops and eyes Nicopressed to spec for your small craft.  Price is for all three shrouds for each boat.  Please pick the appropriate shroud package for your...

from $95.00

Wire Rope, Rudder Cable, Stainless Steel

1/16" wire rope is used in our FeatherCraft Rudder Systems as control cables.  3/32" wire rope is used to make shrouds for the Passagemaker Dinghy and the Northeaster Dory.  Use Nico Sleeves and Thimbles to create loops in the...

1/8 Stainless Steel Thimble 6 Pack

This stainless steel thimble is used with the nico sleeve and wire rope to make shrouds for the Passagemaker Dinghy and the Northeaster Dory. 

Nico Sleeve 6 Pack

These nico sleeves, also known as oval sleeve swages, are used to created loops in our wire rope.  We use 1/16" wire rope and sleeves as control cables for Feathercraft Rudder systems.  3/32" wire rope and sleeves are used for...

1 1/2" 6061-T6 Aluminum Tube

If you are building a kit from plans now the hunt is over for your aluminum mast.  The 6061-T6 grade aluminum tubing measures 1-1/2" O.D. with a 1/8" wall-thickness.  It's used in several of our sailing kits including the very...

from $32.00

Combined masthead cap and halyard sheave fitting for 1-3/8" ID aluminum masts.  Used in the CLC SailRig, Passagemaker, and Mill Creek sailing rigs Epoxy into place.

Harken Small Boat High Load Furling System

Harken® Small Boat furling systems allow the dinghy or trailerable cruising sailor to set and furl the jib from the cockpit. The drums and halyard swivels of these furling systems feature multiple stacked races of Delrin® or Torlon®...

Harken Big Bullet Block w/Becket - 38mm

Low-friction Bullet blocks lead control lines aft. They are compact and lightweight, with fast trim and release under high or low loads. A range of styles lets these blocks adapt to almost all control line applications.

Harken Big Bullet Block - 38mm

Harken Single Bullet Swivel Block - 29mm

Harken's Single Bullet Block with Swivel is great for sailing dinghies and other small sailboats.  Used on PocketShip and on any other sailing vessel where clean leads for control lines are needed.  Specs: Sheave Diameter: 1-1/8"...

Harken Micro Cheek Block - 22mm

Harken Micro Cheek Block Description Cheek Sheave dia. (in) 7/8 Length (in) 2-1/2 Weight (oz) 3/4 Max. line dia. (in) 1/4 SWL (lb) 200 Breaking strength (lb) 1200  

Harken Carbo Cheek Block - 29mm

Harken 29mm Carbo Cheek Blocks are great for control lines: vangs, outhauls, cunninghams, spinnaker controls, traveler controls, and more.  This block is lightweight and compact, with quick trim and release under all loads.  Accepts line...

Harken Carbo Block - 40mm

Low-friction Carbo Air blocks are lightweight, strong, reliable—and affordable. Companions to the popular Harken Black Magic block line, these small, compact blocks have very high working loads for safe, easy trimming.

Harken Swivel Carbo Block - 40mm

Carbo AirBlocks® are 60% stronger and 30% lighter than Harken's Classic blocks. The nylon-resin sideplates are densely packed with long-glass fibers for a compact block with a high strength-to-weight ratio. Sheaves spin on high-load ball...

Harken Swivel Carbo Block - 57mm

The Harken Swivel Carbo Block is low-friction, lightweight, strong, reliable and affordable. Companions to the popular Harken Black Magic block line, these small, compact blocks have very high working loads for safe, easy trimming.

Harken Ratchet Swivel Carbo Block - 75mm

Carbo ratchets represent a new line of on/off switchable 75mm ratchets, available in multiple configurations, for all ratchet applications on dinghies and keelboats. They feature lightweight nylon resin sideplates, densely packed with long glass...

Harken Swivel Ball and Socket Base

The Harken 461 stand-up base allows a variety a blocks to be held upright and swivel and pivot freely.  Complementary hardware for the Harken 2670 Carbo Ratchet Mainsheet Block.  Found on PocketShip and any CLC...

Harken Spring - 22mm

Springs support blocks on padeyes, eyestraps, bases, and traveler cars, and prevent blocks from hitting the deck.

Harken Cam 150 on Swivel Base w/Bullseye Fairlead

The Harken 240 combines a swivel, padeye fairlead, and the 150 cam cleat.  Ideal for main sheets, jib sheets, and spinnaker sheets on dinghies, or any other lines that you need to turn and cleat off.  We use them on PocketShip for jib...

Harken Standard Cam-Matic Kit, Wire Fairlead

This lightweight Cam-Matic cleat with from Harken allows your line to be engaged in the cam even coming in at an acute angle.  Combines the Harken 150 Cam with with the Harken 298 Wire Fairlead.  Used on PocketShip and on sailing...

Harken Micro Cam-Matic Cleat

Harken® ball bearing cam cleats hold lines securely and release instantly for easy, precise trimming. Aluminum Cam-Matics® are hardcoat-anodized for high-load, high-wear, continuous adjustment applications.

Harken Micro Wire Fairlead

Wire fairleads maintain a low profile while holding the line close to the cleat (Harken Micro Cam-Matic Cleat). 

Plastic Eye Strap

These are the plastic eyestraps (padeyes) that we use for Arctic Hawk deck rigging.  Great for attaching all kinds of kayak deck rigging, such as bungie cord and perimeter lines.  And they won't corrode.  Fasteners not...

Stainless Steel Eye Strap

Stainless steel eyestrap, for sailboat rigging.  For use with #8 screws.  

Harken Offshore Eyestrap - 52mm

Eyestraps are useful accessories. They form light-duty mounting bases for blocks, serve as lash-down points, and can be used for fairleads.

Bronze Fairlead

Cast bronze with a smooth tumbled finish. Allows up to 1/4” line to be neatly led. Two mount holes for #10 fastener.

Bronze Lifting Ring & Strap

Rugged towing or lifting ring and strap, ideal for small dinghies and tenders. Cast bronze with a smooth tumbled finish. Ring OD 2-1/8", ID 1-3/8". Strap 2-1/4" long.

Brass Padeye

4-screw flange for bow and stern lines. Looks classy on the bow of any boat, or anywhere you need to fasten something. Use #8 screws (Not included). The eye opening measures about 3/4" x 3/4".  The screwholes are on 1-3/8" centers on the...

Bronze Round Padeye

These rugged cast bronze padeyes have many uses. Dead-ending boom sheets, terminating lifelines and jacklines, and attaching deck blocks are just a few of the jobs the handy Spartan padeye handles.

Marine Grade Plastic Cleat

Marine grade, 4 inches long. Standard issue on CLC sailboats.  Useful everywhere:  sailboat rigging, kayak tow lines, boat hoisting arrangements in garages, etc.

Brass Cleat

These small brass cleats are classy accents for your beautiful wooden sailboat.  Available in 3" or 4" lengths. 3" cleat Requires 2 #8 x 1 1/4" bronze screws (not included)  4" cleat Requires 2 #10 x 1 1/4" bronze screws (not...

from $14.99

Belaying Pin

  Traditional belaying pins for traditional smallcraft.  Standard issue in sailing versions of the Southwester Dory, these pins are hand-turned in the USA with oak handles and maple pins.  They feature a 1/2" diameter x 4-1/2" pin...

Webbing Eye Strap (pair)

These high quality chrome over bronze webbing tie down eye straps.  They are a great option for anchoring your Performance or Sonic back bands or other applications that use 1" flat webbing.  Often used to hold down marine battery boxes...

Size: 10-24 x 1-1/2", high-quality stainless eyebolts you can use for just about anything.  We use them as the rudder gudgeon for the CLC Sailing rig rudders (qty 4).

Stainless Steel Eye Bolt

Stainless steel eye bolt by Sea Dog.  1/4" x 3-3/8" (includes nut and washer) For use with CLC Sailrig to attached the akas to the kayak hull.  Has many other uses too.

Perimeter Line - Black Solid Braided Nylon Rope

1/8" & 1/4" Black Solid Braided Nylon Rope. Shock absorbent nylon blend, ideal for marine use. Recommended for deck perimeter line, securing boats & cargo.  Strong, abrasion resistant. Flexible, easy to knot. Won't rot or mildew....

Samson Mini Braid Cord - Black 5/32" (4mm)

With a polyester cover and nylon core Samson's Accessory Cord has excellent flexibility knotting and strength characteristics for a free running, torque-free cord.Breaking Strength:  1,175• Non-fade, highly wear resistant polyester...

Flat Webbing - Colored

Marine-grade polypropylene, 1” wide, sold by the foot for hatch hold-down straps, seat rigging, and a dozen other chores on kayaks and small boats.  Choose color in pull-down; black is also available. Here's how to use flat...

Bungie Cord Black

For deck hold-downs. 1/4” diameter, black.  The same marine-grade bungie cord we ship with our kits and use on our own boats.  Sold by the foot and now available in six different colors Here's how to tie a knot in this bungie...

Flat Webbing - black

Marine-grade polypropylene, black, 1” wide, sold by the foot for hatch hold-down straps, seat rigging, and a dozen other chores on kayaks and small boats.  Also available in six colors, see below. Here's how to use flat webbing...

Kayak Deck Fitting Double Loop - Set of 6

Six (6) Kayak Deck Fittings, injection molded nylon.

Kayak Deck Fitting Single Loop - Set of 6

Six (6) Deck Fittings.

Lashing Hook 2 Hole - Set of 6

Our recommended two hole lashing hook.

Folding Paddle Clip

Kayak Folding Paddle Clips are most commonly used for paddles.  Paddle clips are available in size 1"- 1-3/4".  Includes Two (2) Paddle Clips.  Paddle clip base requires #8 flat head screws(2 each).

Flush Deck Rigging Fittings

These "Maroske Style” Flush Rigging Fittings are an elegant solution for installing deck rigging and perimeter line on your prized kayak or standup paddleboard.  Rather than mounting bulky pad eyes on the deck surface, the deck rigging...

Harken Tiller Extension - 36"

The simple and lightweight design has no unnecessary frills—every aspect contributes to its strength, stiffness, or comfort. The universal joint and nonslip foam grip are UV-protected and perfect for full dagger-grip and fingertip steering.

Lighthouse Peapod Yawl Rig Sailing Hardware Package

Sailing Hardware Package for the Lighthouse Tender Peapod's Yawl Rig: DESCRIPTION ITEM NAME PART NUMBER QTY(ft) Mainsheet Carbo Fiddle Block - 57mm HAR 2623 1 Block - 40mm Single/Swivel/Becket HAR 2637 1 Padeye for...

PocketShip Sailing Hardware Package

When shipped with the PocketShip boat kit, sail track will be packed and shipped in the boat kit boxes in 8' lengths.  When shipped alone sail trail will be in 7' and shorter lengths.  Padeyes Pad Eye 5/8x2-1/4 SCH...

Outrigger Junior Sailing Hardware Package

Cleats 5" Open Base Cleat SCH 7095 2 Sheave Harken Cruising ESP Sheave - 57mm HAR 6063 1 Satinless Hex Machine Bolts 18-8 Stainless Hex Machine Bolts 5/16"-18 FAS MB5163 1 SS Flat Washer 1" x 2" OD SS Flat Washer...

Pennants, or streamers, have an ancient history in sailing vessels.  600-year-old paintings of sailing ships show them. They were indispensable to warships during the Age of Sail, as they identified the vessel and the captain aboard. ...

Neoprene Rubber Gasket - Pre-cut Patterns

These 1/8" neoprene rubber gaskets are CNC-cut to fit our two take-apart dinghy models and our sectional kayak: the Passagemaker Take-Apart Dinghy, the Eastport Nesting Pram and the Sectional Shearwater Sport.  Building a take-apart design...

from $13.99

1805 GEORGE AVENUE ANNAPOLIS, MARYLAND 21401 USA © 2018 Chesapeake Light Craft, LLC All rights reserved. Reproduction in whole or in part without written permission is prohibited. 

»  YouTube/clcboats1 » Instagram / clcboats »  FaceBook/clcboats

» Boatbuilders' Forum » CLC Builders' Club » CLC Around The Web » Customer Testimonials »  Compare Our Boats » Kayak Specs Table   » Homebuilt Boat Bazaar » International Orders » Manage Account » Customer Service »  Refunds & Returns » Shipping Schedule » Live ShopCam » Site Map