|
WE SHIP WORLDWIDE! We charge the actual cost of shipping. You may email us for a shipping cost estimate. intensitysails(at sign)gmail.com US$10 MINIMUM ORDER |
Before you head out on the water laser sailing, you have to rig your dinghy, and if you have never done this before, it may seem a little overwhelming.
There is no real order in which you should rig your Laser sailboat. There are many combinations and ways of rigging a laser sailboat, and that shown below is simply one combination. Talk to a few people as you rig up, have a few goes yourself, and you’ll work out which way works best for you.
It’s always good to rig up a few times at home before you head out laser sailing if it’s practical and safe to do so. This is recommended so that you are confident that you know what goes where, and so that you can remember how you tie the knots .
As mentioned, there are many different ways when rigging a Laser sailboat. Below is 1 suggestion of the rigging sequence…
Check the weather.
Check the forecast before you leave home, and look outside to check for yourself. Safety should be your first priority, so if the conditions are not suitable for your level of experience, then you may want to reconsider heading out.
If you have been out sailing before, it’s a good idea to pack all your gear away neatly so that it is easy to find, This means that when you pack all your gear to head out sailing the next time, you will know where everything is and you won’t forget anything.
There is nothing worse than getting down to the waterfront and then start to rig your laser sailboat only to find that you have forgotten something crucial (eg. your sail or life jacket), and have to head home before you have made it out onto the water.
It’s easy to get excited about heading out for a great day on the water. However, before you leave, take a minute to check that you have everything packed.
Detach the trailer/dolly.
If the trailer has to be detached from the car when parked, do this 1st. Then slide the dolly/trolley off the trailer, and position it relatively close to where you will launch, with the bow pointing into the wind.
Unpack all your other laser sailing gear , including sail, ropes, foils, and spars , and lay it out to make sure it is all there.
Some people like to get dressed in their sailing gear before they start rigging their boat. If you get dressed at the start, then as soon as you have finished rigging, you can hit the water immediately. It also means that your sail won’t flog as much and cause any extra wear and tear and that your boat won’t accidentally tip over while on the dolly… which may happen especially if there is quite a strong breeze blowing.
Lay the boom on the deck. Feed the mainsheet rope through the blocks and eyelet on the boom, and through the block in the cockpit and the traveler .
It is advisable to tie a figure 8 knot in both ends of the mainsheet rope so that it doesn’t pull through when out on the water. At the boom end, this is so that the mainsheet can be pulled fully on so that it is in the block-to-block position. At the other end so that it doesn’t pull through the mainsheet block in the center of the cockpit.
Leave it loose and un-cleated. Feed the outhaul rope along the boom also.
Next to the hull, lay the sail out and install the battens. Connect the 2 mast sections, and feed it up through the mast sleeve in the sail, making sure the boom spigot is in line with the sail.
Also be careful to ensure that there is no mud or dirt on the bottom of the mast (this may over time cause abrasion between the bottom of the mast and the mast step, which may eventually compromise the integrity of the hull).
Ensuring there are no overhead obstructions (including power lines), from the bottom ½ of the mast, lift it up almost vertical (slightly leaning into the breeze may make it easier to handle), and slot it gently into the mast step hole. This may prove to be a little awkward, so obtain assistance if required
With the mast in place, slot the boom into the mast, and tie off the outhaul to the sail clew using a bowline, as shown in the knots section. Then attach the clew tie-down , making sure to tie it underneath the outhaul.
Attach the vang and cunningham . Tie a small loop in the end of the cunningham and feed the end of the vang pin through it. This will keep the eye of the cunningham down low near the deck, stopping it from riding up (see photo below). Then feed the cunningham through the 2 eyelets in the rope itself, then down to the eyelet on the deck, and run it back to the cleat in the cockpit. Tie a bowline in the end for easy gripping when on the water.
A knot ( bowline or figure 8 knot ) in the end of the cunningham is essential, as it is the only thing preventing the rig from becoming completely detached from the hull when capsized.
Attach the rudder , making sure that the lift stop clicks into place, and leave it in the fully up position. Insert the tiller and fasten the retaining pin, ensuring that the tiller is underneath the traveler.
Lay the centerboard on the deck. Put in the drain plug in the stern of the hull.
With the mainsheet eased right out, the boat should sit quite contently while you tidy up your gear, sail bag, etc. However, if there is a breeze, be careful that your dinghy will not tip over while it is on the dolly, or that the boom will swing around and hit someone.
If it is windy, this is probably not the best time to be going out for a sail if you are a beginner.
If you are not already dressed in your wetsuit, rash vest , life jacket, hat , sunscreen , glasses, shoes , etc, now is the time to do so. It’s a good idea to get someone to keep an eye on your boat and laser sailing gear if you have to go to the change rooms.
With the mainsheet eased, carefully wheel the dolly around, down the ramp, and into the water. Keep the laser sailboat pointing into the wind as much as possible, however as long as the mainsheet is eased you should be able to manage ok as long as the wind is less than 90° to the hull. If possible, do not allow the wind to exceed 90° to the hull.
Wheel the laser dolly into the water until it is fully submerged, and float the boat off the dolly. If you are on your own you may have to run the boat up onto the beach so that you can pull the dolly back out of the water (be careful not to damage the drain plug on the bottom of the hull, or the hull itself). Otherwise, get someone to pull your dolly out for you.
With the boat pointing into the breeze, slide the centerboard into the fin case so that it is most of the way up, but low enough so that the boom clears the fin when it swings around. Run the elastic retaining strap up to the eyelet at the bow and back to the centerboard or mast (the tension in the elastic creates friction so that the centerboard will remain in place when capsized ).
If you are in deep enough water, you will be able to push the rudder down or pull the rope attached to the rudder head, to rotate the rudder to its fully down position. If this can’t be achieved, then you may have to wait until you push the boat into deeper water to do this. Once the rudder is down, tie off the line, and make sure that you do not hit it on the bottom. Take every precaution to protect your foils.
Now, you’re ready for your 1st sail .
When de-rigging, simply reverse the order of the above steps.
If possible thoroughly wash all your gear in fresh water and dry all your gear before storage.
Also take care when folding the laser sail to not create a crease in the sail window, as it will weaken and eventually crack.
As mentioned, there are many different ways of rigging a Laser sailboat. Some have to do with personal preference of rigging order. Some differences also have to do with different types of gear and sailing accessories that you may have (eg. turbo kit, wind instruments, etc). We can’t cover every possible scenario here, so just have a go and see what works for you.
Also, make sure to check out the video below which talks some more about rigging a Laser sailboat, and enjoy your laser sailing :)
Previous: Sailing Knots
Next: Your First Sail
In the Laser cunningham and vang photo there appears to be extra ropes attached for the outhaul could you please describe what was done to achieve that
Hi Kyle The outhaul is a separate rope that runs from the clew of the mainsail up and around the mast and through a cleet to lock it off at the desired tension. It is separate from the cunningham and vang. You can see more about it here . I hope that this helps to answer your question. If not, let me know. cheers
The Laser sailboat is a popular single-handed, one-design sailing dinghy known for its simplicity and performance. Designed by Ian Bruce and Bruce Kirby in 1970, the Laser has become the world's most popular adult and youth sailboat, with over 225,000 boats in 140 countries.
The boat's versatility is a significant contributing factor to its popularity, as it can be customized for different sailors and conditions using three interchangeable rigs of different sail areas.
Laser sailboats offer both beginners and experienced sailors the joy of sailing with their user-friendly design and competitive performance capabilities .
With a strong focus on sustainability, LaserPerformance, the leading producer of Laser sailboats, actively works to minimize the environmental impact of their products through ethical sourcing and manufacturing practices.
The Laser sailboat, an internationally popular one-design class, was conceived in 1969 by Bruce Kirby , a Canadian designer and former Olympian. He aimed to create an innovative design that was simple, affordable, and easy to sail.
The prototype, originally called the "Weekender," was first introduced to the public in 1971 at the New York Boat Show . Its inaugural sail featured the insignia "TGIF," a reference to its early name.
The boat's simplicity and performance attracted sailors of all skill levels, and by the early 1970s, it had become a commercial success.
The International Laser Class Association (ILCA) was established in response to the growing popularity of this sailboat. The ILCA sought to standardize the Laser's various specifications and ensure consistency across all boats.
One of its key contributions has been the establishment of three interchangeable rigs: Standard, Radial, and 4.7 , which cater to different wind strengths and crew weights.
This adaptability has made the Laser more accessible and appealing to a broader range of sailors.
The Laser's rise as an international class was further solidified when it became an Olympic class in 1996. The boat's simplicity, strict one-design nature, and large worldwide fleet have made it a staple of the Olympic sailing program.
Its design has remained relatively unchanged since its inception, with only minor modifications being made to improve performance and durability .
The Laser remains a popular choice for sailors globally, both competitive and recreational. Its unique combination of simplicity, adaptability, and performance has ensured its continued success as a one-design class, and the International Laser Class Association continues to play a crucial role in maintaining the consistency of the boat and promoting the sport of sailing around the world.
The Laser sailboat is known for its simplicity and performance which was designed in 1970 by Ian Bruce and Bruce Kirby. The hull design contributes to its stability and speed in the water.
Its construction uses a lightweight hull, ensuring optimal handling for sailors of various skill levels. This sailboat has been designed with durability and stability in mind.
Its materials and construction techniques focus on withstanding the rigors of sailing while maintaining a consistent and smooth ride on the water.
There are three interchangeable rigging variants for the Laser sailboat, each offering different sail areas to accommodate sailor weight and wind strength. These variants include:
The Laser sailboat has specific dimensions and sail measurements which contribute to its design and performance. Here are the key dimensions:
The sail measurements for the three different rigging variants are as follows:
Rig Variant | Sail Area (sqm) |
---|---|
Laser 4.7 | 4.7 |
Laser Radial | 5.1 |
Laser Standard | 7.1 |
These specifications ensure consistent performance and ease of handling for sailors in various conditions and preferences.
The Laser sailboat is known for its excellent handling and maneuverability, making it suitable for sailors of all skill levels.
Its simplified rigging and straightforward design allow for easy control and quick response to changes in wind and water conditions.
The Laser's hull weight is only 120 pounds (54.43 kg), contributing to its nimbleness on the water.
Steering the Laser sailboat is mostly dependent on the sailor's body positioning and sail trimming techniques, giving more room for tactical excellence. Due to its responsive nature, the Laser rewards sailors who can make quick adjustments and maintain an optimal sail trim.
The Laser sailboat offers a good balance of speed and stability for both recreational and competitive sailing.
Its relatively simple design, combined with a large sail area of 75 square feet (6.97 square meters) , enables it to reach impressive speeds for its size while maintaining stability.
Key factors affecting the Laser's speed and stability include:
A significant aspect of the Laser sailboat's performance is the level of interaction between the sailor and the boat.
As mentioned earlier, the Laser rewards sailors who possess excellent steering and trimming techniques, as well as a strong sense of tactical awareness.
This interaction allows the Laser to perform at its best under various conditions.
Sailors can further optimize their Laser sailboat's performance by:
Laser sailboats are a type of one-design dinghies, which means that they follow strict design and manufacturing rules to ensure all boats in the Laser class are identical.
The versatile laser class is widely popular as they offer different sail and rig sizes, catering to sailors of various ages, weights, and skill levels.
The Laser Standard , also known as the ILCA 7 , is the largest of the three laser rigs. This adult racing class boat features a 7.1 sqm sail, making it suitable for heavier and more athletic sailors.
The Laser Radial or ILCA 6 has a smaller 5.1 sqm sail. It is specifically tailored to lighter sailors, including women and youth sailors. The Radial's sail allows for better control and easier handling in various wind conditions.
This provides a level playing field for a wide range of sailors in terms of age, weight, and experience level.
Lastly, the Laser 4.7 or ILCA 4 features the smallest sail, measuring 4.7 sqm. This rig is designed for young sailors who are new to Laser sailing and need a more manageable sail size. The unique 4.7 lower mast section includes a pre-bend near the boom fitting, which allows the sail to depower more easily.
This provides a more forgiving experience for new and younger sailors.
Each Laser sailboat variant utilizes the same hull design, ensuring that the core sailing experience remains consistent across the board. This enables sailors to transition seamlessly between the different rig sizes as they progress in their sailing abilities.
The Laser sailboat has been a popular choice in the sailing community for competitive racing due to its simplicity and one-design class. The Laser Class Association organizes races and regattas in various formats where sailors adhere to the class rules.
The laser class has three different sail sizes - Laser Standard (ILCA 7), Laser Radial (ILCA 6), and Laser 4.7 (ILCA 4). These cater to sailors of different ages, weights, and abilities to participate in a single class.
These characteristics make the Laser sailboat a widely sought-after option for sailors who are interested in competitive racing 1 .
The laser class has a strong presence in the Olympics, being recognized as an Olympic class sailing dinghy. Laser Standard (ILCA 7) and Laser Radial (ILCA 6) are the two divisions that have been part of the Olympic Games since 1996 and 2008, respectively.
With its universal appeal and the level playing field it offers to sailors, the laser class has grown significantly in popularity over the years. It has achieved global recognition as a highly competitive sailing class in the Olympic Games.
Alongside racing, regattas and their Olympic presence, the Laser Class Association also organizes various national and international championships.
Among these events are the ILCA 4 Youth World Championship, scheduled to happen in Viana do Castelo, Portugal, in June 2024 2 .
The World Championships typically attract top sailors from different nations, competing for the title of world champion.
A list of major championships for laser sailing includes:
In addition to these flagship events, many national championships are also held regularly by various Laser Class Associations around the world. This fosters the growth of talented sailors and promotes the spirit of competition within the laser sailing community.
Laser sailboats are known for their durability, but regular maintenance is essential to ensure their longevity and maintain resale value.
Inspect the hull and foils for any damage or signs of wear. Also, check the steering systems, such as rudder and tiller, ensuring they are functioning smoothly without any wiggles.
Regularly inspect tiller extension fittings for cracking and signs of potential breakage.
Cleaning your sailboat after each use will help minimize the chance of damage from dirt, salt, and debris. Store sails, lines, and other equipment properly to avoid moisture damage, mold, and mildew growth.
Verifying the functionality of the autobailer should also be a part of the routine maintenance process.
Transporting a Laser sailboat can be done with relative ease, as they are lightweight and their compact size allows for cartop transport.
When cartopping your Laser, use appropriate padding and straps to secure the boat without causing damage to the hull, mast, or other components.
As for storage, it is essential to keep your Laser sailboat in a covered and well-ventilated area, preferably on a dolly or custom cradle that supports the gunwales to prevent unnecessary stress on the hull.
Moreover, ensure the mast and other equipment are safely stored alongside the boat.
Periodically inspect the boat during storage to check for any signs of damage, moisture buildup, or rodent infestation.
The Laser sailboat has built a strong sense of community that extends across different countries. This community primarily revolves around clubs, associations, and social and recreational sailing.
A significant part of the Laser sailing community is the involvement in clubs and associations at various levels. The International Laser Class Association (ILCA) is the governing body that brings together Laser sailors from all around the world.
This association is responsible for maintaining the one-design principles, organizing international events, and promoting Laser sailing as a high-quality, competitive sport.
At a local level, numerous clubs are home to passionate Laser sailors. Club racing is a popular form of competition within the community, offering a friendly yet competitive environment for sailors to test their skills.
There are also regional associations supporting the growth of the Laser sailing community in their respective areas.
Example of Laser clubs:
The Laser sailboat's appeal extends beyond competitive racing, with many enthusiasts enjoying the boat for its simplicity and versatility in social and recreational sailing.
The Laser community is known for organizing events that cater to various interests and skill levels, ensuring that everyone has a chance to find their niche.
Some common social and recreational sailing events include:
When looking for a Laser sailboat, various factors such as brand, condition, materials used, size, and additional features all play a role in determining the price .
A brand-new Laser will typically cost more than its used counterpart. Higher quality materials and improved technology can also increase the price, as well as customizable options and additional accessories.
To find the right Laser sailboat at a competitive price , it's essential to compare offerings from various vendors and take time to evaluate factors like reputation and warranty. Sailing Chandlery provides more information on Laser sailboats and their prices.
When considering a Laser sailboat, pay attention to details like hull weight , rig size, sail size, and weight capacity , as these will affect the boat's performance and suitability for the intended use.
A standard Laser sailboat generally has a hull weight of 125 lbs or 56.7 kg , with different sail sizes available, such as ILCA 4 (Laser 4.7), ILCA 6 (Laser Radial), and ILCA 7 (Laser Standard).
Each sail size is designed for sailors within specific weight ranges, providing the best performance and stability.
To find a reputable vendor for Laser sailboat kits, research different suppliers, seek recommendations from fellow sailors, and read reviews from previous customers.
Online platforms like West Coast Sailing offer resources and information on Laser sailboats, including detailed guides, FAQs, and where to find quality suppliers.
The recommended weight capacity for a Laser sailboat varies depending on the rig size.
The ILCA 6 (Laser Radial) is suitable for sailors between 60 kg and 75 kg , while the ILCA 7 (Laser Standard) is better suited for sailors weighing 75 kg to over 90 kg.
The ILCA 4 (Laser 4.7) is designed for younger and lighter sailors. When choosing a Laser sailboat, ensure that the rig size matches the intended user's weight range for optimal performance.
The best Laser sailboats on the market offer a combination of durability, performance, and ease of use.
Look for models with robust construction. They are made from high-quality materials to withstand harsh sailing conditions.
Additionally, seek sailboats with easy-to-use rigging systems and low-maintenance designs.
Also, make sure they have support from reputable manufacturers. This ensures they meet strict class specifications.
Sailing a Laser is generally suitable for beginners. These boats are known for their simplicity, ease of use, and responsive handling. However, beginners should be prepared for some challenges.
These challenges include mastering the correct body positioning and balance or adjusting to different wind and weather conditions. It's essential for new Laser sailors to familiarize themselves with the boat's assembly and rigging process and seek guidance from experienced sailors or trainers. This ensures a safe and enjoyable sailing experience.
The best things in life have only one thing in common:
They are unique…
Eu target: 32% reduction.
Eu target: 40% reduction, sailing news, sunfish quality report 2023, mediterranean games, sunfish worlds.
Cookie | Duration | Description |
---|---|---|
cookielawinfo-checkbox-analytics | 11 months | This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Analytics". |
cookielawinfo-checkbox-functional | 11 months | The cookie is set by GDPR cookie consent to record the user consent for the cookies in the category "Functional". |
cookielawinfo-checkbox-necessary | 11 months | This cookie is set by GDPR Cookie Consent plugin. The cookies is used to store the user consent for the cookies in the category "Necessary". |
cookielawinfo-checkbox-others | 11 months | This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Other. |
cookielawinfo-checkbox-performance | 11 months | This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Performance". |
viewed_cookie_policy | 11 months | The cookie is set by the GDPR Cookie Consent plugin and is used to store whether or not user has consented to the use of cookies. It does not store any personal data. |
A regular at the Laser Masters worlds and championships across Europe, Max Hunt runs Southeast Sailboats – a small business that provides custom made rigging solutions - www.southeastsailboats.co.uk
A look around the dinghy park at a major Laser event shows there is no right way to rig your control lines. Much of how we rig our Laser is down to what we are comfortable with, maybe we just haven’t changed what seems to work, or perhaps we don’t think that good rigging matters. Having good controls is important as it takes one more variable out of your racing: they are strong and well built, they allow you to trim your sail correctly even when you are tired, they are always rigged the same – all of which provide psychological and mechanical advantages.
No matter how you rig your Laser, in a world of marginal gains, good rigging can make a difference by reducing risk of failure, maximizing ease of use and consistency.
What can be done? Your rigging should be easy to fit in the same way from event to event so that nothing changes and your calibration remain consistent. It should also be secure – barely a major event goes by without seeing someone suffer rigging failure.
Avoiding tying and untying knots is one way of achieving these first two objectives. Having some of your lines and blocks spliced, providing it is done properly, can give you both consistency and increased security. The latest generation of blocks is designed to be ‘soft attached’ using Dyneema® or similar line but tying them on incorrectly can result in the block being pulled apart at the head. A good solution is to Brummel (lock) to splice them in the right position in the first place.
Soft attach blocks such as these from Harken can fail if incorrectly attached. The tied on blocks on the left are marginal – under load, the line is starting to pull the head of the block apart. Splicing these blocks on correctly is a safer option.
Pro Laser Sailboat Rigging: Rudder & Tiller
Also, for example at the clew, instead of tying on blocks, small Dyneema loops can be used as a more secure alternative, whether you prefer a shackle, hook or a block attached to the clew.
Simple and secure – Dyneema loops are an effective solution to attaching a 29mm Carbo Block to your clew shackle or hook. Smaller blocks such as Ronstan’s 20mm Orbit block used with a spliced loop can be threaded through the clew and back through the loop.
A third objective is to ensure our systems are easy to use by making them more effective and efficient by choosing the right blocks, ropes, and considering more purchases. Increasing purchase is most appropriate for the cunningham when using the new heavier MKII standard sail, and as the range of travel on the new sail is smaller, it reduces the 8:1 downside of more rope in the cockpit.
When considering block types, larger sheave sizes up to the maximum 30mm allowed under class rules, increase efficiency due to their reduced rolling resistance, and these can make a real difference particularly on the highly loaded cunningham. Here, blocks such as Harken’s 29mm T2 Soft-Attach Carbo blocks are ideal.
Effective, efficient systems reduce the effort you need to put into changing your settings, making accurate adjustments faster and easier, especially when you are tired.
Southeast Sailboats fully spliced 8:1 cunningham is specially designed for the new MKII standard sail. The lower block assembly is passed through the loop on the primary and then under the kicker tang to fix it all in place. No knots to tie or come undone, no shackles or pins to undo. Effective, efficient, consistent, secure.
When it comes to rope types much is down to personal preference or maybe it was just what was available at the time. There are a lot of performance criteria in rope selection but for control lines on the Laser, the most important is minimal stretch under load so that settings remain unchanged, whilst being strong, low in friction and friendly on the hands.
Slippery Dyneema® SK78 D12 is the default choice for primary lines. The cunningham primary must do a 180 through the tack cringle/grommet and minimizing friction is important as pulling the cunningham on is hard enough. The cunningham primary line diameter is a compromise between having a thin line that risks getting trapped in the gooseneck, or thicker line and greater friction. The outhaul primary also has to do a 180 through the boom end eye but with a lighter load than the cunningham and a larger bend radius.
Whereas primary lines should be slippery, our secondary lines should be ‘hands friendly’ both in terms of diameter and grip. Polyester / Technora® covered and/or Dyneema® cored 4mm line is the default here although some sailors are using naked 4mm D12 SK78. Good color usage on secondary lines is vital, ensuring that you can quickly distinguish and instantly grab the correct control line. Rope lengths should also be set ‘just right’ to minimize excess line in the cockpit, and so you can use the handle to maximum effect.
With everything set up perfectly you can minimize mistakes and tangles and maximize the consistency, effectiveness and security of your controls.
Finally, little things like frayed rope end, outer covers that are separating from their cores, knots to try and tie in a consistent place can result in lost time rigging, or more worryingly frustration, when we should be concentrating on what is important. Having all our rigging clean with spliced lines, and properly stitched or sealed rope ends can help eliminate this potential source of psychological disadvantage.
The top mainsheet core is starting to pull out of the cover making rigging frustrating. Worse still if the cover is pulling off and your stopper knot doesn’t hold the core. The lower mainsheet end has been stitched with Dyneema and covered with heat shrink sleeving secured with epoxy adhesive.
In competitive situations where marginal gains are important, just like having straight spars, aligned foils, a polished hull, and a good sail having a well-rigged Laser mean that you haven’t let that element to chance.
Be sure to check out Southeast Sailboats !
⛵️ Fast Dispatch and a 5 Star Rated Service ⛵️
Your Cart is Empty
Tax included and shipping calculated at checkout
Order before midday Monday to Friday and we will ship your order the same day.
Zhik Superwarm
Mini Spools
New Devoti ILCA
November 11, 2022 3 min read
The Laser 6-1 Outhaul System is now the standard that comes with all new boats. If you are finding your outhaul is very difficult to adjust it may be time to upgrade your system.
In this article, we walk you through what you'll need and how to make a Laser 6-1 Outhaul System step by step.
You can also buy the full Laser Outhaul Kit on our website.
Some ropes will need to be cut to your correct length once the system is made. This system is tied together with knots however, we would always recommend when working with Dyneema lines to splice them as this is stronger than knots.
The first part of the Outhaul System is going to be the clew block and hook. There are lots of different ways that people rig this. We will do it per the instructions you receive with a new boat. Take one of the 18mm blocks, the clew hook and one length of the 3mm race rope.
Tie a stopper knot in one end of the line and thread it through the centre of the block and up through the top of the block. Now grab your clew hook and thread the line through and back down into the top of the block. Lastly back through the middle of the block and tie another figure of 8.
Primary Dyneema
Take your length of 3mm Dyneema and tie a bowline around the eye on the boom end.
Now thread your line through the clew block from step one and the Dyneema back through the boom eye. The rope will then run along the boom towards the front of the boat.
Control line
Take your 4mm Race rope and an 18mm block. Thread the 4mm line about 3 inches through the centre of the block.
Now with the Primary Dyneema thread it into the top of the same 18mm and tape both lines together using the photo below as a reference.
Pull both through and tie a bowline in each.
Take your next 18mm block and a length of 3mm race rope and tie it into the cleat on the boom. This should face backwards down the boom towards the back of the boat.
Control line
Now thread the control line from the bowline you have tied through the mid-block tied to the boom and back through the block the bowline is tied onto going around the sheave. This will create your 6 to 1 purchase.
Take your last 18mm block and 3mm race top and tie a bowline around the block and the loose end will be tied around the lower mast where the boom and mast meet. This block acts as the turning point where the control line rope goes along the boom and down towards the deck plate.
The control line rope will then go through the deck block at the bottom of the mast and backwards through the cleats on the deck.
Elastic/ Shockcord
Thread the shockcord through the cleat on the top of the boom then tie a stopper knot. Now the other end can be tied to the sail or the clew hook as shown below.
If you have any questions on the Laser 6 to 1 outhaul system please get in touch with our team who are always happy to help.
Makes a more secure anchorage than a stopper knot
A stock of rope and cordage is essential for the proper function of any sailing club. Floating and non-floating rope are needed equally. This is a good product, at a reasonable price - if bought on the reel.
My first Zhik spray top, but just like the rest of the gear from Zhik the combination of design, material selection and style are spot on. I’ve been wearing the top in the Dragon, Edinburgh Cup where there has been a rain and significant spray at time. The top has kept me warm and dry. Especially impressed with the neck seal. Dry, yet not constricting.
Boots arrived quickly and were a great fit
Very Good A+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Service excellent as always . The pads are great for laser sailing
Just what I was looking for, good to be able to buy any number of toggles I needed.
I bought some kingfisher spliceable rope to replace a continuous control line. It's an easy splice and that's down to the quality of the rope supplied by the Sailing Chandlery.
It’s a nice halyard thing and strong, and looped through itself it has a slim profile. Also I need extra length and sailing chandlery where happy to add it on for me! Greatt!
A perfect match, installed and working well.
I do wish there was a less expensive shipping alternative for your international customers.
great products , great service
Great product! As always, the team at Sailing Chandlery delivered a great customer experience.
Lovely dry bag, good size, tough sturdy bag. Feels well made.
Save up to 40% on your next order.
Last Updated: February 1, 2024
wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 25 people, some anonymous, worked to edit and improve it over time. This article has been viewed 147,594 times. Learn more...
This is a step by step instruction on how to rig the original laser.
wikiHow Tech Help Pro:
Develop the tech skills you need for work and life
Alex Morgan
Rigging a Laser sailboat is an essential skill for anyone interested in sailing. Properly rigging a sailboat ensures that all components are securely in place, allowing for a safe and enjoyable sailing experience. This article will provide an introduction to rigging a Laser sailboat, explain the different components involved, and provide a step-by-step guide on how to rig the boat. It will offer tips and best practices to follow while rigging, as well as common mistakes to avoid. Whether you are a beginner or an experienced sailor, mastering the art of rigging a Laser sailboat is crucial for a successful outing on the water.
As we dive into the world of laser sailboats , it’s crucial to understand the nuts and bolts that make up these vessels. In this section, we’ll take a look at the key components that come together to form a laser sailboat . From the sturdy mast to the versatile boom , and the intricate rigging lines to the billowing sail , we’ll navigate through each element, unraveling their significance and how they contribute to a successful sailing experience. Get ready to explore the inner workings of laser sailboats and gain a deeper appreciation for their craftsmanship.
The mast is an essential component of a Laser sailboat as it provides vital support and stability to the sail. Constructed from either lightweight and strong carbon fiber or aluminum, the mast is designed to withstand the powerful forces of wind and water.
When rigging a Laser sailboat, the first crucial step is to carefully insert the mast into the mast step located at the base of the boat’s hull. Once inserted, it is important to raise the mast upright and secure it using a mast clamp or collar for stability.
The next important task is to attach the sail to the mast. This is achieved by raising the sail and securing it using halyards or sail ties. It is vital to properly tension the sail in order to optimize performance and maintain control while sailing.
Throughout the rigging process, it is imperative to regularly check the mast for any signs of damage or wear. It is essential to promptly address any cracks or weaknesses to ensure the safety of both the boat and the sailor while out on the water.
In order to prolong the longevity and enhance the performance of the mast, regular inspections, cleaning, and lubrication of the mast fittings are necessary. This will help prevent corrosion and ensure smooth operation during sailing sessions.
The boom is a necessary part of a Laser sailboat . It is a horizontal spar that extends from the mast. This sturdy pole controls the shape and position of the sail.
Attaching the boom is a crucial step in rigging a Laser sailboat . It involves sliding one end into a fitting on the mast called the gooseneck . The boom is secured with a boom vang , a line that runs from the mast to the boom . This vang controls the tension and angle of the boom , allowing sailors to adjust the sail’s shape and power.
Properly attaching and adjusting the boom is essential for efficient sailing. It allows the sailor to control the sail’s position and shape based on wind conditions. Adjusting the boom optimizes the sail’s power and performance, maximizing speed and maneuverability.
The use of booms in sailing has a long history. It originated from the use of horizontal spars to control the shape of sails on large sailing ships. Over time, booms have become an integral part of smaller sailboats, enhancing sailing performance and control. Nowadays, booms are used in various sailboat designs, including the Laser .
To properly rig a Laser sailboat, it is important to understand the components involved, including the rigging lines. Here are the steps to follow:
1. Begin by setting up the main halyard. Attach it to the head of the sail and run it through the top of the mast.
2. Next, secure the main sheet. Attach one end to the boom and run it through the blocks on the back of the boat.
3. Connect the cunningham line. Start by attaching one end to the cunningham eyelet on the front of the mast and run it through the block on the boom.
4. Establish the vang line. Attach one end to the vang fitting on the mast and run it through the block on the boom.
5. Attach the outhaul line. Connect one end to the outhaul fitting on the boom and run it through the outhaul block on the back of the boom.
6. Secure the traveler line. Attach one end to the traveler block and run it through the block on the back of the boat.
By following these steps, you can effectively rig the rigging lines on a Laser sailboat. It is important to check the lines for wear or damage before sailing to ensure a safe and enjoyable experience.
The sail is a crucial component of the Laser sailboat. It efficiently harnesses the power of the wind and propels the boat forward. The sail is carefully constructed using durable and lightweight materials, typically synthetic fibers like Dacron or Mylar .
The sail is securely attached to both the mast and the boom, forming a triangular shape that effectively captures the wind. The size of the sail plays a significant role in the boat’s overall performance. Sails of smaller sizes are ideal for lighter winds, whereas larger sails are more effective in stronger winds.
To properly rig the sail, it is important to securely attach the boom to the mast. Then, the sail should be hoisted up the mast, ensuring correct alignment and tension. The cunningham and outhaul lines can be adjusted to control the shape and tension of the sail.
Taking proper care and maintenance of the sail is crucial for its longevity and optimal performance. Prolonged exposure to direct sunlight should be avoided, as it can cause damage to the sail. Regular inspection for wear and tear is necessary, and any necessary repairs or replacements should be made promptly.
A well-rigged sail is essential for a successful sailing experience, allowing the boat to efficiently capture the power of the wind and maneuver through the water. By familiarizing yourself with the various components and following the correct rigging procedures, you can ensure that your Laser sailboat is ready for an exciting and rewarding adventure on the water.
Looking to hit the waves with your Laser Sailboat ? Mastering the rigging process is key to a successful sailing experience. In this step-by-step guide , we’ll walk you through the essentials of rigging a Laser Sailboat . From stepping the mast to hoisting and adjusting the sail, we’ve got you covered. Get ready to set sail with confidence and navigate the waters like a pro !
To properly step the mast of a Laser sailboat, you should follow these steps:
By following these steps, you can guarantee that the mast is properly stepped and securely fixed, providing a strong foundation for rigging the rest of the Laser sailboat.
To attach the boom to a Laser sailboat , follow these steps:
1. Position the boom near the mast , aligning the gooseneck with the mast slot .
2. Slide the boom all the way through the mast slot .
3. Align the holes on the boom fitting with the holes on the mast fitting .
4. Insert the boom bolt through the holes and securely fasten it with a nut if needed.
5. Check that the boom is securely attached and moves smoothly along the mast .
True story: When rigging my Laser sailboat for the first time, I struggled to align the boom fitting with the mast fitting . After a few attempts, I realized I needed to adjust the boom’s position slightly for proper alignment. Once adjusted, the boom slid into place smoothly, and I secured it with the bolt . This experience taught me the importance of attention to detail when rigging a sailboat.
Securing the Rigging Lines
To secure the rigging lines on a laser sailboat, follow these steps:
By securing the rigging lines on a laser sailboat, the sail will be correctly positioned and tensioned for optimal performance on the water.
In order to hoist and adjust the sail properly, ensure that the halyard is properly attached to the sail and securely fastened . Stand towards the mast and pull on the halyard to raise the sail up the mast. Continue pulling until the sail is fully hoisted to the top of the mast, making sure there are no twists or tangles.
To achieve the desired sail shape based on wind conditions and personal preference, adjust the halyard tension. You can tighten or loosen the halyard to adjust the sail shape. Tightening the halyard will flatten the sail, while loosening it will add more depth .
For different wind conditions, make small adjustments and observe how the sail responds to find the optimal setting. Once the desired sail shape is achieved, secure the halyard by tying it off or using a cleat.
Let me share a true story: One time during a race, while I was hoisting the sail on my Laser sailboat, a sudden gust of wind caught the sail and caused it to billow dramatically . Fortunately, I quickly adjusted the halyard tension and regained control of the sail. This experience taught me the importance of properly hoisting and adjusting the sail to maintain stability and control on the water.
Tips and Best Practices for Rigging a Laser Sailboat
– Start with a well-maintained boat: Check for any damages or wear and tear that may affect the rigging process.
– Properly attach the mast: Use the mast step to securely attach the mast to the boat and ensure proper alignment.
– Attach the boom: Connect the boom to the mast using the gooseneck fitting and make sure it is securely fastened and aligned.
– Attach the mainsheet: Thread the mainsheet through the mainsheet blocks and tightly secure it to the boom for proper control while sailing.
– Attach the sail: Carefully center and align the sail on the mast, securing all sail ties to prevent it from coming loose.
– Tension the rigging: Optimize sailboat performance by adjusting the rigging tension to control the sail shape and maximize speed.
– Check all fittings and lines: Before setting off, inspect all connections to ensure they are secure and in good condition, including the halyard, vang, cunningham, and outhaul.
A sailor followed all the rigging steps meticulously, resulting in a well-rigged laser sailboat that effortlessly glided through the water during a regatta. Their attention to detail paid off as they sailed to victory, impressing their competitors with their skills and precision. This experience highlights the importance of following best practices and tips for rigging a laser sailboat to achieve success on the water.
When rigging a Laser sailboat, it is important to avoid common mistakes that can negatively affect performance and safety. Here are some key points to keep in mind:
1. Correct sail positioning: Make sure to hoist and tension the sail properly. Incorrect positioning can result in poor trim and reduced speed.
2. Adequate rig tension: Proper tension is crucial for optimal performance. Avoiding insufficient tension will prevent a loose sail and decrease control.
3. Mast alignment: Always align the mast with the boat’s centerline. Deviation from this alignment can affect weight distribution and stability.
4. Efficient use of controls: Take the time to familiarize yourself with the cunningham, vang, and outhaul controls. Proper use of these controls will allow for adjustments to changing conditions.
5. Regular maintenance: Regularly inspect the rigging for any signs of wear or damage. Neglecting maintenance can lead to equipment failure and compromise safety.
By avoiding these common mistakes, you will enhance your sailing experience and ensure optimal performance. Remember to practice proper rigging techniques and comply with Laser Class rules.
Faqs on how to rig a laser sailboat, 1. how do i assemble the mast of a laser sailboat.
To assemble the mast, slide the bottom of the top half into the top of the bottom half. Then, slide the sail over the mast using the pocket along one side of the sail. Insert the battens into the sail and ensure they are secured.
Attach the front end of the boom to the gooseneck on the mast. Then, walk around to the flapping end of the sail while holding the boom on the gooseneck. Run the outhaul rope through the eye at the end of the boom and cleat it off. Rig the mainsheet by tying one end around the eye on the bottom of the pulley at the end of the boom and running the other end through the traveler on the stern of the boat, through the pulley on the end of the boom, and down through the main block at the front of the cockpit.
To stand up the mast, carefully lift it and place it into the mast step at the front of the laser. Use the middle of the mast for better control and walk forward while pushing the sail up. As for the boom vang, attach it to the bottom of the mast and slide it into the metal clip on the bottom of the boom. Pull down on the hanging line and cleat it off.
Attach the rudder by inserting it into place and securing it with the tiller. Make sure the lift stop clicks into place. For the daggerboard, tie a long loop of elastic to the eye at the end of the dagger board and secure it to the boat.
Before rigging, check the weather forecast and pack all necessary gear, including the sail, ropes, foils, and spars. Also, ensure that the hull plug is screwed into the drain hole in the stern of the boat. Check that you have a life jacket and other personal safety equipment.
Before launching, tidy up the area and ensure the boat is secure. If needed, detach the trailer or dolly from the car and position it close to the launch area. Double-check that all gear is packed and ready. When in deep water, always put on a rash vest and googles for added protection.
About the author
Your email address will not be published. Required fields are marked *
Save my name, email, and website in this browser for the next time I comment.
History of Sailing Sailing is a time-honored tradition that has evolved over millennia, from its humble beginnings as a means of transportation to a beloved modern-day recreational activity. The history of sailing is a fascinating journey that spans cultures and centuries, rich in innovation and adventure. In this article, we’ll explore the remarkable evolution of…
Solo Sailing Sailing has always been a pursuit of freedom, adventure, and self-discovery. While sailing with a crew is a fantastic experience, there’s a unique allure to sailing solo – just you, the wind, and the open sea. Single-handed sailing, as it’s often called, is a journey of self-reliance, resilience, and the ultimate test of…
Eco Friendly Sailing Sailing is an exhilarating and timeless way to explore the beauty of the open water, but it’s important to remember that our oceans and environment need our protection. Sustainable sailing, which involves eco-friendly practices and mindful decision-making, allows sailors to enjoy their adventures while minimizing their impact on the environment. In this…
by Emma Sullivan | Jul 20, 2023 | Sailboat Gear and Equipment
The Laser 2 sailboat is a high-performance sailing dinghy designed for racing and recreational sailing. It features a single trapeze, a mainsail, and a jib, providing exciting and responsive sailing experiences. Its hull is made from fiberglass, making it durable and lightweight.
Have you ever dreamed of harnessing the power of the wind and gliding across the open waters? If so, then the Laser 2 Sailboat is just what you need to make those dreams a reality. With its sleek design, nimble handling, and unparalleled performance, this classic vessel has been a favorite among sailing enthusiasts for decades.
The Laser 2 Sailboat is renowned for its ability to thrill both beginners and experienced sailors alike. Whether you’re looking to learn the ropes or test your skills in competitive racing, this versatile boat is up to the task. Its simple rigging system and responsive controls make it easy to handle, even for novices. And with its durable construction and steady buoyancy, it can withstand any conditions Mother Nature throws at it.
One of the most captivating aspects of the Laser 2 Sailboat is its incredible speed. Once you catch a gust of wind in its fully battened sail, you’ll feel an exhilarating rush as you slice through the water like a knife. The combination of its lightweight hull and powerful sail allows for impressive acceleration and top speeds that will leave other boats trailing behind. It’s no wonder why sailors around the world have fallen head over heels in love with this legendary vessel.
But don’t be fooled by its fast-paced nature – the Laser 2 Sailboat also offers plenty of opportunities for leisurely cruising and exploration. Its spacious cockpit can comfortably accommodate two or three people, making it perfect for adventurous outings with friends or family members. Take a lazy afternoon sail along picturesque coastlines or navigate tranquil lakes while enjoying breathtaking views – there’s no limit to where this magnificent vessel can take you.
What truly sets apart the Laser 2 Sailboat from other sailboats is its community. Joining fellow sailors who share your passion for adventure and camaraderie makes every sailing experience all the more enjoyable. Connect with experienced professionals who can offer valuable tips on technique, equipment, and maintenance. Engage in spirited discussions about your latest sailing adventures or upcoming regattas. With the Laser 2 Sailboat, you’ll become part of a tight-knit group that spans the globe, bound together by a love for this remarkable vessel.
So, if you’re ready to embark on an unforgettable sailing journey, look no further than the Laser 2 Sailboat. Experience the sheer thrill of harnessing the power of wind with its unmatched performance and speed. Immerse yourself in a vibrant community of like-minded sailors who will inspire and support you along the way. Get ready to create memories that will last a lifetime – because once you’ve experienced sailing with this classic vessel, there’s no turning back.
Sailing is an ancient art that has captivated humans for centuries, invoking a sense of freedom, adventure, and pure bliss. If you’ve ever daydreamed about gliding effortlessly across the water with the wind in your hair, then learning how to sail a Laser 2 sailboat might be the perfect endeavor for you. In this step-by-step guide tailored specifically for beginners, we will explore the intricacies of sailing a Laser 2 and offer tips to help you master this exhilarating hobby.
Step 1: Understanding the Basics Before setting foot on a Laser 2 sailboat, it’s crucial to grasp the fundamental concepts of sailing. Familiarize yourself with key terms such as “tacking” (changing direction against the wind), “jibing” (changing direction with the wind behind you), and “points of sail” (different angles at which a boat can travel relative to the wind). Learning these essentials will serve as your foundation in becoming a skilled sailor.
Step 2: Preparing Your Laser 2 Sailboat Once you’ve familiarized yourself with sailing’s terminology, it’s time to prep your vessel. Ensure that all necessary equipment is on board and properly functioning- from ropes and rigging to sails and rudders. A well-maintained boat guarantees a smoother sail and contributes significantly to overall performance.
Step 3: Rigging Your Boat Rigging refers to setting up your boat, including attaching sails and rigging ropes correctly. This process can seem daunting at first but fear not! It becomes second nature with practice. Pay close attention to maintaining proper tension in your rigging lines – too loose or too tight can impact maneuverability considerably.
Step 4: Launching Your Laser 2 Sailboat You’re now ready for launch! Identify a safe location with suitable access points for entering the water; preferable areas would have few obstructions like rocks or shallow waters. Be mindful of wind conditions and direction before venturing out to ensure a more enjoyable experience – light to moderate winds are ideal for beginners.
Step 5: Safety First Never underestimate the importance of safety during any sailing activity. Before setting sail, equip yourself with a personal flotation device (PFD) and ensure everyone on board does the same. Also, be aware of weather forecasts and water currents that can affect your journey. Remember, wise sailors prioritize safety above all else.
Step 6: Balancing Act Mastering balance is vital when sailing a Laser 2 sailboat as shifts in body weight greatly impact agility and speed. Finding your center of gravity as you maneuver, particularly during turns or gusts of wind, will optimize your boat’s performance. Train your mind and body to anticipate these changes; it is both an art and a science.
Step 7: Navigating the Wind Understanding the nuances of wind direction is key to becoming an accomplished sailor. Study how sails behave when catching the wind at different angles, known as points of sail mentioned earlier. Adjusting the angle between the sail’s edge and the wind will allow you to harness its power efficiently while simultaneously controlling your course.
Step 8: Mastering Tacking and Jibing Now comes the exciting part – changing directions! Tacking refers to turning into the wind by bringing the bow through it; jibing involves turning away from the wind with it behind you. These maneuvers require practice, timing, and coordination between crew members (if applicable). As you become more proficient in tacking and jibing smoothly, you’ll experience newfound confidence in maneuverability.
Step 9: Advanced Skills & Techniques Congratulations! You’ve grasped the basics and are now ready to delve into more advanced techniques such as fine-tuning sail trim (adjustment), mastering upwind sailing angles, or even attempting tricks like planing (sailing at high speed with hull lifting out of the water). These skills come with time and experience, so continue pushing your boundaries as you evolve in your sailing journey.
Step 10: Continued Learning Sailing is an art that can never be fully mastered. The beauty lies in continuous learning, honing your skills, and embracing new challenges. Join sailing clubs or communities to exchange knowledge and experiences with fellow enthusiasts. Embrace the lifelong process of understanding wind patterns, experimenting with sail configurations, and exploring different bodies of water. Be open to new discoveries!
In conclusion, mastering the art of sailing a Laser 2 sailboat requires patience, dedication, and enthusiasm. With this step-by-step guide for beginners as your compass, set sail on a transformative journey that will unlock a world of adventure and sheer joy out on the open waters. Let the wind carry you toward newfound horizons as you become one with nature through the sport of sailing!
Title: Frequently Asked Questions About the Laser 2 Sailboat: Everything You Need to Know
Introduction: Ahoy, sailing enthusiasts! Whether you are new to sailing or a seasoned sailor, one boat that has undoubtedly caught your attention is the Laser 2 Sailboat. In this comprehensive guide, we will address some of the most commonly asked questions about this remarkable vessel. So grab your captain’s hat, secure your lifejacket, and let’s set sail into the world of the Laser 2!
1. What Makes the Laser 2 Sailboat So Special? The Laser 2 Sailboat stands out for its versatility and high-performance capabilities in both cruising and racing scenarios. The boat features an innovative design that combines speed and stability like no other. Its two-man configuration allows for collaboration between sailors while maneuvering through varied wind conditions, making it truly unique among its counterparts.
2. How Does It Differ from Other Sailboats? While there are many sailboats on the market, the Laser 2 sets itself apart through its adaptability. This vessel can be equipped with various rigging options according to your skill level or desired sailing style. From a single-sail setup for beginners to twin-trapeze configurations for advanced racers seeking an adrenaline rush – there is something for everyone!
3. Is It Beginner-Friendly? Absolutely! The Laser 2 caters to sailors of all expertise levels. Novice sailors can embark on their nautical adventures with confidence due to its forgiving nature and stable hull design. With accessible controls and simplified rigging systems, those new to sailing will find it easy to learn the ropes while still experiencing thrilling moments on the water.
4. How Do Its Racing Capabilities Compare with Other Boats? For competitive spirits hungry for victories on race day, the Laser 2 won’t disappoint! Its lightweight hull allows for quick acceleration, ensuring you consistently remain at the forefront of races against competitors. The boat’s maneuverability and responsive controls allows for quick adjustments, making it a fierce contender even in highly competitive fleets.
5. Can It Be Sailed Single-Handed? Yes, it can! Though designed as a two-person sailboat, the Laser 2 can be sailed solo by experienced sailors who prefer going solo or need some solitude on the water. With appropriate modifications and adjustments to the rigging systems, it is possible to enjoy the Laser 2 experience single-handedly.
6. What Type of Maintenance Does the Laser 2 Sailboat Require? The Laser 2 is known for its durability and low-maintenance requirements. Its robust construction ensures longevity, while simple systems make maintenance tasks hassle-free. Regular cleaning after each sail and occasional inspections of rigging components should suffice to keep your Laser 2 in top-notch condition for years of enjoyment.
7. Where Can I Find Spare Parts or Accessories? Fear not, fellow mariner! The Laser 2 community is strong, with passionate enthusiasts regularly sharing tips, tricks, and information about spare parts or accessories. Numerous online retailers specialize in providing genuine Laser 2 components to ensure you find exactly what you need with ease.
Conclusion: Now that we have delved into the world of frequently asked questions about the remarkable Laser 2 Sailboat, you are equipped with vital knowledge that will help you set sail confidently upon its sleek hull. Whether you’re seeking casual cruising adventures or craving exhilarating races, this versatile vessel has got your back covered. So cast off from land and embark on unforgettable aquatic expeditions aboard the magnificent Laser 2 – where thrill meets tranquility!
Introduction:
The Laser 2 sailboat is not your ordinary watercraft. It is a remarkable fusion of design, engineering, and ergonomics that sets it apart from other sailboats in the market. In this blog post, we will dive into the intricacies of its design and explore the array of features that make the Laser 2 a true standout.
1. Lightweight Construction:
One striking feature of the Laser 2 sailboat is its lightweight construction. Meticulously crafted using advanced materials and innovative manufacturing techniques, every component is designed to reduce weight without compromising on strength. This means increased durability while allowing for swift and nimble sailing performance.
2. High-performance Hull Design:
At the heart of the Laser 2’s exceptional functionality lies its masterfully designed hull. Utilizing extensive research and cutting-edge hydrodynamics, this boat glides through water with minimal resistance, maximizing both speed and maneuverability. Its sleek lines seamlessly integrate form with function, making it a sight to behold as it effortlessly slices through waves.
3. Three-sail Configuration:
Unlike conventional sailboats sporting a single or double-sail setup, the Laser 2 boasts a unique three-sail configuration that takes sailing to a whole new level. Consisting of a main sail, jib, and spinnaker, this trifecta offers enhanced control over various wind conditions. Whether you’re gracefully cruising along or chasing adrenaline-fueled speeds, this versatile setup ensures an exhilarating experience for sailors of all skill levels.
4. Ergonomic Cockpit Design:
The Laser 2’s cockpit design strikes an exquisite balance between comfort and functionality. The ergonomically contoured seating positions allow sailors to maintain optimal control while minimizing strain during long journeys or intense racing competitions. Every touchpoint has been meticulously engineered to keep sailors in harmony with their vessel – leading to enhanced responsiveness and precision handling on the water.
5. Rigging Simplicity:
Tying knots and setting up a sailboat can be a daunting task for newcomers. However, the Laser 2 eliminates this complexity by incorporating an intuitive rigging system. With numbered lines and user-friendly adjustments, even novice sailors can quickly learn to set up and fine-tune their sails. By reducing hassle and ensuring ease of use, the Laser 2 empowers sailors to focus on what truly matters – sailing itself.
6. Durability that Stands the Test of Time:
Investing in any watercraft is a significant decision — one that requires assurance of its longevity. The Laser 2’s robust construction ensures it stands the test of time, with high-quality materials and meticulous craftsmanship providing unmatched durability. This means you can confidently embark on countless adventures without worrying about wear and tear impacting your vessel’s performance or structural integrity.
Conclusion:
In conclusion, the Laser 2 sailboat undoubtedly surpasses expectations when it comes to design and features. Its lightweight construction, high-performance hull design, three-sail configuration, ergonomic cockpit, rigging simplicity, and durable build make it shine amidst a sea of ordinary sailboats. Whether you’re an experienced sailor seeking exhilarating thrill rides or a beginner looking to enter the world of sailing, the Laser 2 sets itself apart as a sophisticated watercraft that guarantees unforgettable experiences on every voyage.
Safety Tips and Precautions for Sailing a Laser 2 Sailboat: Enjoying Your Adventure Responsibly
Sailing a Laser 2 Sailboat can be an exhilarating experience, allowing you to explore the open waters and enjoy the serenity of the sea. However, just like any other water sport, it’s crucial to prioritize safety and take necessary precautions to ensure an enjoyable adventure. In this blog post, we will provide you with detailed professional advice on how to safely navigate your Laser 2 Sailboat while still having a witty and clever time!
1. Mind the Weather Forecast: Before setting sail, always check the weather forecast thoroughly. Wind speed, direction, and potential storms are critical factors that can greatly influence your sailing experience. While it may seem exciting to challenge yourself in rough conditions or strong winds, it’s essential to understand your abilities and limitations as a sailor. Remember, responsible sailors don’t disregard signs of inclement weather – they adjust their plans accordingly.
2. Get Comfortable with Your Boat: Knowing your boat inside out is paramount for safe sailing adventures. Take the time to familiarize yourself with every aspect of your Laser 2 Sailboat – from its rigging and sails to its navigation instruments and safety equipment. A witty sailor knows their boat intimately; better understanding ensures you’re prepared for any situation that comes your way.
3. Safety Equipment Should Be Your Best Friend: Never set sail without properly equipped safety gear! Life jackets are at the top of the list – make sure you have enough for each crew member aboard your Laser 2 Sailboat. Additionally, carry flares or alternative signaling devices in case you need help in an emergency situation — cleverly choose colorful flares that match your vibrant personality!
4. Communicate Effectively: Before embarking on your sailing journey, let someone else know about your plans. Share details including departure time, estimated return time, planned route (if applicable), and emergency contact information. Keeping friends or family informed allows them to keep an eye out for your well-being from the shore, and they’ll appreciate your responsible approach to adventuring.
5. Buddy System: Sailing is more enjoyable when you have company. Not only does sailing with a partner enhance your overall experience, but it also enhances safety. In case of an injury or other unforeseen circumstances, having a buddy on board ensures that there’s always someone available to assist or seek help if needed — plus, you can share witty banter during those long stretches of calm waters!
6. Keep Your Phone Dry: While it may seem obvious, we cannot stress enough how important it is to keep your phone protected from water damage. We live in a world where being connected is essential – not just for capturing clever Instagram stories but also for emergencies. Today’s smartphones are often equipped with waterproof or resistant features; however, carrying them in a proper waterproof case will provide an extra layer of protection – just in case things get too wet and wild!
7. Education is Key: Investing time in expanding your sailing knowledge through courses and certifications will undoubtedly make you a safer sailor. Understanding navigation rules, reading charts or maps, and knowing how to react in different boating situations are invaluable skills that come with education and training. Being professionally skilled while exhibiting a clever wit ensures admiration from fellow sailors!
8. Respect Nature: Finally, always respect the environment around you when sailing your Laser 2 Sailboat. Avoid littering, decrease noise pollution as much as possible (we know it can be difficult when celebrating witty victories on the high seas!), and follow guidelines for responsible anchoring practices.
In conclusion, enjoying sailing adventures responsibly means putting safety first while injecting some wit and charm into every voyage aboard your Laser 2 Sailboat! By following these tips and precautions diligently, you can confidently navigate the open waters while having fun, ensuring your adventure is memorable for all the right reasons. Happy sailing and stay cleverly safe!
Unleashing Your Competitiveness: Racing Techniques and Strategies in a Laser 2 Sailboat
Introduction: Sailing is a sport that has captured the hearts of adventurers and thrill-seekers since time immemorial. The sense of freedom, mastery over nature, and the adrenaline rush offered by sailing are unparalleled. Amongst all the sailboat classes out there, the Laser 2 is renowned for its exhilarating speed, maneuverability, and versatility. Whether you’re an experienced sailor or a novice looking to dive into competitive racing, this blog post will guide you through some ingenious techniques and strategies to unleash your competitiveness in a Laser 2 sailboat.
1. Mastering Boat Handling: A vital aspect of successful racing in a Laser 2 is mastering boat handling skills. This includes understanding how to efficiently maneuver your vessel through various wind conditions, waves, and currents. Being able to extract maximum speed from your sailboat while maintaining control requires finesse. Practice tacking (turning the bow of the boat through the wind) and jibing (turning the stern through the wind) until these maneuvers become second nature.
2. Effectively Using Sail Controls: Sail controls play a crucial role in optimizing your overall performance on water. Familiarize yourself with the main controls available on a Laser 2: mainsheet, traveler, vang/kicker, cunningham/downhaul, and outhaul; each has its own purpose in fine-tuning your sails’ shape and power efficiency. Understanding how to trim your sails using these controls can make a significant difference in speed and responsiveness.
3. Tactical Decision-Making: Racing involves not just raw sailing skills but also strategic decision-making on the racecourse. Analyze wind shifts meticulously to anticipate changes before they occur and position yourself advantageously on the course accordingly. Keep an eye on other competitors’ tactics as well; learn from their successes but also be ready to adapt and counter their moves. Sail smart, exploiting any tactical opportunity that arises to gain an edge over your rivals.
4. Teamwork: For those participating in two-person or three-person Laser 2 racing, effective teamwork is paramount. Communication between teammates on boat handling, sail setting adjustments, and tactical decisions need to be smooth and seamless. A synchronized effort between the helmsman and crew can make the difference between a win and a loss. Develop trust with your team members, learn each other’s strengths and weaknesses, and work in tandem towards a common goal.
5. Physical Fitness: Sailing may not seem like an intense physical activity at first glance, but maintaining optimal fitness levels is vital for competitive success in a Laser 2 sailboat race. Cardiovascular endurance helps you sustain high energy levels throughout demanding races, while strength training allows you to handle the boat’s forces efficiently during maneuvers. Core stability exercises are indispensable for maintaining balance on trapezing boats like the Laser 2.
Conclusion: Unleashing your competitiveness in a Laser 2 sailboat is a journey that combines technical mastery of boat handling, strategic decision-making, effective teamwork, and physical fitness. Investing time in honing these skills will undoubtedly elevate your racing game to new heights of excellence. So embrace the thrill of competition, embrace the adventure that comes with sailing a Laser 2, and prepare to unleash your full potential as you conquer the waves with style!
Free Shipping Over $99 - 366 Day Returns - Expert Advice
Over 200,000 Laser sailboats have been built over the last 40 years, more than most other small dinghy sailboats. In this article we are going to answer one of the most common questions we get: What size rig do I have? This will help answer what size sail and/or rig you already have and what size sail and/or rig you need to purchase to update your Laser.
What size rig / sail do I have? Standard vs. Radial vs 4.7 Explained
The Laser sailboat has had a number of different rig sizes, with the intention of making the boat sailable by a wide range of sailors (and different sailor weights) by simply swapping out the lower mast section and sail while keeping all other components the same. There are currently three different rig sizes and they are commonly referred to as 'Standard', 'Radial' and '4.7'. Below you will find an image that shows the three rigs side by side, and in the following section we'll explain each one.
Laser Standard / MK2 / ILCA 7
This is the most common Laser rig size, and the original rig on the boat when it was designed. It features a 7.06 square meter sail (about 76 square feet). In 2018, the Laser Class approved a new 'Standard' sail, which is referred to as the 'MKII' or 'Mark 2' to distinguish it from the first version. The difference, among other things, is in the panels. The original 'Standard' sail featured horizontal cut panels. The new MkII sail has radial cut panels. There is no difference in size between these two versions, and as of 2020 all new Laser Standard sails are available in this updated cut.
How to tell if you have a 'Standard' sail: The first and most obvious way to tell if you have a 'Standard' sail is to look at the panels. If they are horizontal, it is most likely a standard sail. Next, you can measure the luff (the front edge of the sail along the mast sleeve). This measurement should be about 5130 mm or 200 inches from the top of the sail to the bottom.
How to tell if you have a 'Standard' lower mast section: The 'Standard' lower mast section should measure about 2865 mm or 113 inches . It is a fairly stout mast section compared to the two smaller mast sections.
Laser Radial / ILCA 6
Originally called the 'M' rig when first designed, the Laser 'Radial' sail is smaller than the 'Standard' sail at 5.76 square meters (62 square feet). At the time, it was the only Laser sail to feature the radial cut panels, which allowed the sail to be de-powered more easily in bigh winds. Per the notes about the 'Standard' rig above, both the Standard and Radial sail feature the radial cut design. Another typical indicator of a Radial size sail are the blue panels at the tack and clew of the sail.
How to tell if you have a 'Radial' sail: The first and most obvious way to tell if you have a 'Standard' sail is to look at the panels. If they are radial, as in emanating out from the center, it is most likely a radial sail. Next, you can measure the luff (the front edge of the sail along the mast sleeve). This measurement should be about 4560 mm or 180 inches from the top of the sail to the bottom.
How to tell if you have a 'Radial' lower mast section: The 'Radial' lower mast section should measure about 2262 mm or 89 inches . It is also a bit smaller in diameter than the standard section.
Laser 4.7 / ILCA 5
The Laser 4.7 (or ILCA 5) is the smallest of the three Laser sails and was designed for young sailors just getting into Laser sailing. The 4.7 lower mast section is also different from the others in that is has a pre-bend near the boom fitting, allowing the sail to depower much easier. This is the least common Laser sail size, and if you have an old one around, chances are it is not a 4.7 sail.
How to tell if you have a '4.7' sail: The 4.7 is similar to the old 'Standard' sail as it has cross cut panels. Many 4.7 sails also have an obvious 4.7 logo somewhere on the cloth. Next, you can measure the luff (the front edge of the sail along the mast sleeve). This measurement should be about 4080 mm or 160 inches from the top of the sail to the bottom.
How to tell if you have a '4.7' lower mast section: The '4.7 lower mast section has a pre-bend in it and should measure about 1810 mm or 71 inches . The bend is the easiest way to tell it apart from the others.
<< Previous page
Pages: 379-406
In 1988, the Tuvan Archaeological Expedition (led by M. E. Kilunovskaya and V. A. Semenov) discovered a unique burial of the early Iron Age at Saryg-Bulun in Central Tuva. There are two burial mounds of the Aldy-Bel culture dated by 7th century BC. Within the barrows, which adjoined one another, forming a figure-of-eight, there were discovered 7 burials, from which a representative collection of artifacts was recovered. Burial 5 was the most unique, it was found in a coffin made of a larch trunk, with a tightly closed lid. Due to the preservative properties of larch and lack of air access, the coffin contained a well-preserved mummy of a child with an accompanying set of grave goods. The interred individual retained the skin on his face and had a leather headdress painted with red pigment and a coat, sewn from jerboa fur. The coat was belted with a leather belt with bronze ornaments and buckles. Besides that, a leather quiver with arrows with the shafts decorated with painted ornaments, fully preserved battle pick and a bow were buried in the coffin. Unexpectedly, the full-genomic analysis, showed that the individual was female. This fact opens a new aspect in the study of the social history of the Scythian society and perhaps brings us back to the myth of the Amazons, discussed by Herodotus. Of course, this discovery is unique in its preservation for the Scythian culture of Tuva and requires careful study and conservation.
Keywords: Tuva, Early Iron Age, early Scythian period, Aldy-Bel culture, barrow, burial in the coffin, mummy, full genome sequencing, aDNA
Information about authors: Marina Kilunovskaya (Saint Petersburg, Russian Federation). Candidate of Historical Sciences. Institute for the History of Material Culture of the Russian Academy of Sciences. Dvortsovaya Emb., 18, Saint Petersburg, 191186, Russian Federation E-mail: [email protected] Vladimir Semenov (Saint Petersburg, Russian Federation). Candidate of Historical Sciences. Institute for the History of Material Culture of the Russian Academy of Sciences. Dvortsovaya Emb., 18, Saint Petersburg, 191186, Russian Federation E-mail: [email protected] Varvara Busova (Moscow, Russian Federation). (Saint Petersburg, Russian Federation). Institute for the History of Material Culture of the Russian Academy of Sciences. Dvortsovaya Emb., 18, Saint Petersburg, 191186, Russian Federation E-mail: [email protected] Kharis Mustafin (Moscow, Russian Federation). Candidate of Technical Sciences. Moscow Institute of Physics and Technology. Institutsky Lane, 9, Dolgoprudny, 141701, Moscow Oblast, Russian Federation E-mail: [email protected] Irina Alborova (Moscow, Russian Federation). Candidate of Biological Sciences. Moscow Institute of Physics and Technology. Institutsky Lane, 9, Dolgoprudny, 141701, Moscow Oblast, Russian Federation E-mail: [email protected] Alina Matzvai (Moscow, Russian Federation). Moscow Institute of Physics and Technology. Institutsky Lane, 9, Dolgoprudny, 141701, Moscow Oblast, Russian Federation E-mail: [email protected]
Shopping Cart Items: 0 Cart Total: 0,00 € place your order
Price pdf version
student - 2,75 € individual - 3,00 € institutional - 7,00 €
Copyright В© 1999-2022. Stratum Publishing House
Rusmania • Deep into Russia
Savvino-storozhevsky monastery and museum.
Zvenigorod's most famous sight is the Savvino-Storozhevsky Monastery, which was founded in 1398 by the monk Savva from the Troitse-Sergieva Lavra, at the invitation and with the support of Prince Yury Dmitrievich of Zvenigorod. Savva was later canonised as St Sabbas (Savva) of Storozhev. The monastery late flourished under the reign of Tsar Alexis, who chose the monastery as his family church and often went on pilgrimage there and made lots of donations to it. Most of the monastery’s buildings date from this time. The monastery is heavily fortified with thick walls and six towers, the most impressive of which is the Krasny Tower which also serves as the eastern entrance. The monastery was closed in 1918 and only reopened in 1995. In 1998 Patriarch Alexius II took part in a service to return the relics of St Sabbas to the monastery. Today the monastery has the status of a stauropegic monastery, which is second in status to a lavra. In addition to being a working monastery, it also holds the Zvenigorod Historical, Architectural and Art Museum.
Located near the main entrance is the monastery's belfry which is perhaps the calling card of the monastery due to its uniqueness. It was built in the 1650s and the St Sergius of Radonezh’s Church was opened on the middle tier in the mid-17th century, although it was originally dedicated to the Trinity. The belfry's 35-tonne Great Bladgovestny Bell fell in 1941 and was only restored and returned in 2003. Attached to the belfry is a large refectory and the Transfiguration Church, both of which were built on the orders of Tsar Alexis in the 1650s.
To the left of the belfry is another, smaller, refectory which is attached to the Trinity Gate-Church, which was also constructed in the 1650s on the orders of Tsar Alexis who made it his own family church. The church is elaborately decorated with colourful trims and underneath the archway is a beautiful 19th century fresco.
The Nativity of Virgin Mary Cathedral is the oldest building in the monastery and among the oldest buildings in the Moscow Region. It was built between 1404 and 1405 during the lifetime of St Sabbas and using the funds of Prince Yury of Zvenigorod. The white-stone cathedral is a standard four-pillar design with a single golden dome. After the death of St Sabbas he was interred in the cathedral and a new altar dedicated to him was added.
Under the reign of Tsar Alexis the cathedral was decorated with frescoes by Stepan Ryazanets, some of which remain today. Tsar Alexis also presented the cathedral with a five-tier iconostasis, the top row of icons have been preserved.
The Nativity of Virgin Mary Cathedral is located between the Tsaritsa's Chambers of the left and the Palace of Tsar Alexis on the right. The Tsaritsa's Chambers were built in the mid-17th century for the wife of Tsar Alexey - Tsaritsa Maria Ilinichna Miloskavskaya. The design of the building is influenced by the ancient Russian architectural style. Is prettier than the Tsar's chambers opposite, being red in colour with elaborately decorated window frames and entrance.
At present the Tsaritsa's Chambers houses the Zvenigorod Historical, Architectural and Art Museum. Among its displays is an accurate recreation of the interior of a noble lady's chambers including furniture, decorations and a decorated tiled oven, and an exhibition on the history of Zvenigorod and the monastery.
The Palace of Tsar Alexis was built in the 1650s and is now one of the best surviving examples of non-religious architecture of that era. It was built especially for Tsar Alexis who often visited the monastery on religious pilgrimages. Its most striking feature is its pretty row of nine chimney spouts which resemble towers.
Location | approximately 2km west of the city centre |
---|---|
Website | Monastery - http://savvastor.ru Museum - http://zvenmuseum.ru/ |
Ready-to-book tours.
Your holiday in Russia starts here. Choose and book your tour to Russia.
Looking for something unique? Create the trip of your dreams with the help of our experts.
IMAGES
VIDEO
COMMENTS
The Lockpit is a patented locking storage product designed to secure spars, blades and all the gear needed for your Laser sailboat safely inside the cockpit....
1) Yes! There should be plastic flotation bag like things called cubitainers inside the hull. There are 3, 20 Liter bags aft and 3, 10 Liter bags forward. If yours are not there, it is a good idea to replace them. You can purchase them at any local Vanguard dealer for $9 per 20 Liter bag and $6 per 10 liter bag.
The Lockpit is a patented locking storage product designed to secure spars, blades and all the gear needed for your Laser sailboat inside the cockpit. Page · Sports & recreation. Long Beach, CA, United States, California. (562) 843-9866. [email protected].
SOLD BY THE PAIR. (2 IN PER ORDER) 4SP Price: $40.00 Sale price: $35.00. WE SHIP WORLDWIDE! We charge the actual cost of shipping. You may email us for a shipping cost estimate. Send us email. intensitysails (at sign)gmail.com. US$10 MINIMUM ORDER.
The Laser sailboat has had a number of different rig sizes, with the intention of making the boat sailable by a wide range of sailors (and different sailor weights) by simply swapping out the lower mast section and sail while keeping all other components the same. There are currently three different rig sizes and they are commonly referred to ...
Detach the Trailer/Dolly. If the trailer has to be detached from the car when parked, do this 1st. Then slide the dolly/trolley off the trailer, and position it relatively close to where you will launch, with the bow pointing into the wind. Laser dinghy on the dolly and trailer. Laser dinghy on the dolly, but off the trailer.
Hull Design and Construction. The Laser sailboat is known for its simplicity and performance which was designed in 1970 by Ian Bruce and Bruce Kirby. The hull design contributes to its stability and speed in the water.. Its construction uses a lightweight hull, ensuring optimal handling for sailors of various skill levels. This sailboat has been designed with durability and stability in mind.
The Cascais is the ultimate rotomolded multi-purpose sailing dinghy. Its versatility and innovative design brings together exceptional handling, speed and stability allied with its spacious cockpit and 3 rig/ sail versions makes this the ideal platform for all levels of sailors. We believe that rotomolded boats can be fun and the Cascais is the living proof of this.
A good solution is to Brummel (lock) to splice them in the right position in the first place. ... and a good sail having a well-rigged Laser mean that you haven't let that element to chance. Be sure to check out Southeast Sailboats! Resources. Articles and videos to refine your skills and make you a better sailor. Resources. Clinic Dates.
Step 1. Clew Block. The first part of the Outhaul System is going to be the clew block and hook. There are lots of different ways that people rig this. We will do it per the instructions you receive with a new boat. Take one of the 18mm blocks, the clew hook and one length of the 3mm race rope. Tie a stopper knot in one end of the line and ...
1. Get all your parts together. You should have the boat itself (the hull), the dagger board, the rudder and tiller, your mainsheet, both mast pieces, boom, boom bang and sail in one place. 2. Put together both the pieces of your mast. The bottom of the top half just slides into the top of the bottom half.
To properly rig a Laser sailboat, it is important to understand the components involved, including the rigging lines. Here are the steps to follow: 1. Begin by setting up the main halyard. Attach it to the head of the sail and run it through the top of the mast. 2.
Laser Hiking Strap Rooster Pro. Rooster Sailing. $39.95. 1. 2. 3. Next. Parts for your Laser hull and deck including autobailers, laser deck cleats, vang upgrades, gudgeons, drain plugs, grab rails, Laser hiking straps, racing upgrades and more! Free Shipping over $49.
The Laser 2 Sailboat stands out for its versatility and high-performance capabilities in both cruising and racing scenarios. The boat features an innovative design that combines speed and stability like no other. Its two-man configuration allows for collaboration between sailors while maneuvering through varied wind conditions, making it truly ...
ZIDO5330K586. So... sail number 5330, built by Laser International in Hawkesbury, Ontario, in November 1985 Means no spinnaker launcher, and two gudgeons on the transom (instead of a gudgeon and a pintle), among other things. The trapezes are ok except that the elastic should be tied to the block of the ring fitting, instead of the ring itself.
The Laser sailboat has had a number of different rig sizes, with the intention of making the boat sailable by a wide range of sailors (and different sailor weights) by simply swapping out the lower mast section and sail while keeping all other components the same. There are currently three different rig sizes and they are commonly referred to ...
Burial 5 was the most unique, it was found in a coffin made of a larch trunk, with a tightly closed lid. Due to the preservative properties of larch and lack of air access, the coffin contained a well-preserved mummy of a child with an accompanying set of grave goods. The interred individual retained the skin on his face and had a leather ...
Out of the Centre. Savvino-Storozhevsky Monastery and Museum. Zvenigorod's most famous sight is the Savvino-Storozhevsky Monastery, which was founded in 1398 by the monk Savva from the Troitse-Sergieva Lavra, at the invitation and with the support of Prince Yury Dmitrievich of Zvenigorod. Savva was later canonised as St Sabbas (Savva) of Storozhev.
In 1938, it was granted town status. [citation needed]Administrative and municipal status. Within the framework of administrative divisions, it is incorporated as Elektrostal City Under Oblast Jurisdiction—an administrative unit with the status equal to that of the districts. As a municipal division, Elektrostal City Under Oblast Jurisdiction is incorporated as Elektrostal Urban Okrug.
State Housing Inspectorate of the Moscow Region Elektrostal postal code 144009. See Google profile, Hours, Phone, Website and more for this business. 2.0 Cybo Score. Review on Cybo.